Four 3x3x1/2 equal leg angles are laced together as shown in Figure 3 to form a column section. Determine the Euler (elastic) stress and the critical buckling load (kN) for the pin-connected column. E = 200,000 MPa. Proportional limit is 250 MPa. Assume simple span and maximum permissible L/r = 200. a) L = 11.50 m b) L = 9.75 m P ↑ Properties of one 3 X 3 X 1/2 angle A = 1774 mm² Ix = 0.92 x106 mm4 rx = 22.81 mm L y = 23.67 mm k 300 mm 300 mm ly = 0.92 x106 mm4 ry = 22.81 mm x = 23.67 mm

Four 3x3x1/2 equal leg angles are laced together as shown in Figure 3 to form a column section. Determine the Euler (elastic) stress and the critical buckling load (kN) for the pin-connected column. E = 200,000 MPa. Proportional limit is 250 MPa. Assume simple span and maximum permissible L/r = 200. a) L = 11.50 m b) L = 9.75 m P ↑ Properties of one 3 X 3 X 1/2 angle A = 1774 mm² Ix = 0.92 x106 mm4 rx = 22.81 mm L y = 23.67 mm k 300 mm 300 mm ly = 0.92 x106 mm4 ry = 22.81 mm x = 23.67 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compute for the maximum allowable distributed load o that can be applied to the simply supported beam as shown in Figure M-Va. The beam's cross section is detailed in Figure M-Vb. @(N/m) Allowable Stresses: Fiber Stress = +13.5 MPa / -12 MPa Transverse Shear Stress at NA = 900 kPa Transverse Shear Stress at Junction 800 2 m Figure M-Va 2 m Draw the flexural and shear stress distributions of the cross section. T 40 40 40 Figure M-Vb 40 120 mm
Consider the truss shown in (Figure 1). Suppose that F = 30 kN Figure A 3m 3m < 1 of 1 ▼ Determine the force in the member CD of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case tension. FCD- Value Submit Part B HA Part C Request Answer Determine the force in the member CB of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCB- Value Submit Request Answer HÀ Submit Part D FDA- Value HA Determine the force in the member DA of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive…
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the loadP = 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa C. Aluminum L=2m A=500mm2 2m 2m E-72Mра P=20KN
Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1600 mm?. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 т 10 m 10 m K 6 т G H 6 m 15° 15° 40 kN 50 kN E F 6 т б т А B
A beam having the cross section shown is subjected to a couple M0 acting in a vertical plane. Determine the largest permissible value of the moment M0 of the couple if the maximum stress is not to exceed 103 MPa. Given: Iy = Iz = b4/36 Iyz = b4/72
2. Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 m 10 m 10 m K 6 т H 6 т 15° 15° 50 kN 40 kN E F 6 т C D б т A B
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial load acting on bar Bị in kN. 35KN В1 B2 ВЗ ... 10KN 15KN 30KN Determine the axial load acting on bar B2 in kN. Determine the axial load acting on bar B3 in kN. Determine the axial stress of bar B1 in MPa. Determine the axial stress of bar B2 in MPa. Determine the axial stress of bar B3 in MPa. Determine the total deformation of the bars B1, B2 and B3 in mm. Determine the deformation of the bar B in mm. Determine the deformation of the bar B2 in mm. Determine the deformation of the bar Bz in mm. 35 А 35 B 20 10
Problem 2: The structure consists of a solid rod of length 2L. On the left it is fixed to the wall. An outer sleeve has been securely bonded to the right half of the solid bar so that no slippage occurs between them, and both the bar and the sleeve are fixed to the wall on the right. The cross section is shown below. For your convenience, let: GR=2G, G₁ = G RR=R, R₁ = 2R Calculate the maximum shear stress induced in each of the sections D, , and due to the torque To acting as shown. Rg R₂ Sleeve: G, Solid rod: G ////////////// //////////TITT
Q1) Three bars AB, CD and ED are used to support ACE beam. The three bares have modulus of elasticity E=200 GPa, cross sectional area A=500 mm2. Determine the ww normal stress in each bar due to load P. a a=280mm b=70mm C=1177mm L=1075mm P=775mm L E B D F
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 ВЗ ... 10KN 15KN 30KN A 218.75 B 125 C 62.5 D 31.25
A simple pin-connected truss is loaded and supported as shown. The load P is 240 kN. All members of the truss are aluminum pipes that have an outside diameter of 135 mm and a wall thickness of 9 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 6 m, b = 3.75 m, and c = 3 m. Tensile stress is positive, while compressive stress is negative. b D A B Answer: OAB i JAC = i OBC= i OBD i OCD i || a MPa MPa MPa MPa MPa
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm