For the Zener diode network of figure below, if R = 1 kn, R, = 5 kN, V; = 24 V, Vz = 15 V, PzM = 60 mW;a) determine V,, VR, Iz, and Pz.b) Is the design of the circuit correct, why?RVzPzMVLRL

Zener diode- A Zener diode is a semiconductor diode used to create a stable voltage reference or…

Answered: For the Zener diode network of figure…

For the Zener diode network of figure below, if R = 1 kN, R̟ = 5 kl, V; = 24 V , Vz = 15 V, Pzm = 60 mW; a) determine V,, Vg, Iz, and Pz. b) Is the design of the circuit correct, why? + VR R Vz Pzm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: A Zener diode circuit is shown in Figure Q.1(b). Given Vz = 12 V, (i) Determine I, Vulh and lg…

A: Given Vz = 12 V Izmax = 15 m A. RLmax = Vz/ILmin RLmin = Vz /ILmax

Q: Q3 For the network of figure shown below, determine and Sketch V across the load 120 V resistance R,…

Q: For the given circuit below, compute for the power dissipation of the diode. Si RL 8 k2 Vs 18 V

Q: Q3: Sketch vo for the network of Figure below and determine the de voltage available. Meal 170v…

Q: The circuit below shows a perfect Zener regulator (rz=0), where the diode power rating is not…

Q: The zener diode shown in the circuit below is being used for voltage regulation. Determine the…

A: Redrawing the circuit diagram by marking the current and the voltage as shown below:

Q: From the diode circuit shown below, If E=40 V and RL=800, determine the current supplied from the…

A: Given diode circuit is, Diode is silicon diode with internal resistance of 1 ohm,

Q: Q1/ For the circuit shown below, find Vot, Vo2 and the current through the silicone diode. Ge Vat Si…

Q: Q1/ In the circuit shown below, the zener diode used has the following specifications : Vz= 12 volt,…

Q: Q2- For voltage source Vs=50V, calculate the allowable range of load resistances for the Zener…

A: Given Figure; The power rating for zener diode is given as-…

Q: 3. The Zener diode has Von = 0.7V, Vzo = 5V, and r₂ = 1000. 3 ΚΩ Vs (±10 V 1.5 V + + V₁ W a.…

Q: Q1/ In the circuit shown below, the zener diode used has the following specifications : Vz= 12 volt,…

Q: Assuming that a silicon diode is used in the circuit shown, determine and plot the transfer…

A: From the transfer characteristics

Q: Load-line Analysis a.1 For the series diode configuration employing the diode characteristics given,…

A: as per our guidelines we are supposed to answer?️ only one question. Kindly repost other questions…

Q: 4. For the circuit shown below, a. What is the ac resistance of the emitter diode? b. What is the…

Q: Q3/ Consider the circuit shown below with a transformer of 10:1 transformation ratio and the diodes…

Q: Q2/ (a) Given Pmax = 14 mW for each diode of Fig. , detemine the maximum current rating of each…

A: Given Data: Pmax = 14 mW R1 = 4.7 kohm R2 = 56 kohm

Q: Consider the "Zener diode as a voltage regulator" circuit given below: 1502 D unregulated/ 12 volt…

A: For given Zener diode to operate in a breakdown region is necessary to operate in the reverse-biased…

Q: R QUESTION #1. For the Zener diode network of figure below, if R = 1 k, RL = 5 kN, Vị = 24 V, Vz =…

Q: R1 Vx - Considering the given circuit, Vz = 6.5 V @ 4 mA, R1 = 0.5 kN, V = 12±3 V, and rz 25 N. If…

A: The minimum value of zener diode in breakdown region, if the voltage are given.

Q: Determine range of IL and Ri that will result in VRL being maintained at 10Volts and = 10 mAmperes,…

Q: Let: Vi = 25 V, RS = 250 Ohm, VZ = 12V, PZmax = 450mW A. Determine VL, IL, IZ and IR If RL = 420 Ohm…

Q: Q1/ In the circuit shown below, the zener diode used has the following specifications : Vz= 12 volt,…

A: power P = voltage V * currrent I . at maximum value of current , power will be maximum . generally…

Q: For the circuit shown below, answer the following questions. 2(a + 1)2 I- Plot the load line…

Q: Q1/ In the circuit shown below, the zener diode used has the following specifications : Vz= 12 volt,…

A: According to KVL , voltages in closed loop is zero . let current from source is I , then KVL in…

Q: 2. Calculate the maximum-rated zener current, IZM, for the following -W zener diodes: a. Vz = 5.6 V.…

A: As per guidelines given to us we can only provide the solution of one question in multiple type of…

Q: Determined the range of values for Vin that will maintain the Zener diode in ON state and power…

A: Zener diode are special purpose diodes. It is used as a voltage regulator. Zener diode when…

Q: Q4: A IN4738 zener diode has a knee current of (0.5mA). By using the information from data sheet…

A: solution: 1N 4738 Zener diode Izk=0.5mA I=40 mA

Q: 1) For a diode connected transistor find the AC equivalent resistance.

A: find the Ac Equivalent Resistance

Q: a, DESIGN THE NETWORK IN THE FIGURE, TO KEEP, "VL" at 12 V for a variation in load (IL) from 0 to…

A: According to question: a) As the load voltage has to kept at 12V, so to maintain this value of load…

Q: 2) In the circuit given in the figure, R = 6kN, Zener diode breakdown voltage VZ = 3.6V and www. w…

A: The given circuit is: Here, R=6 kΩVZ=3.6 VPZ=6.5 mW

Q: Q2- For voltage source Vs=50V, calculate the allowable range of load resistances for the Zener…

A: Zener Break down The concept of breaking the covalent bond by creating a strong a strong non-uniform…

Q: For the given circuit: if V, = 15, I,= 17 mA, IK = 0.25 mA, Z, = 14 2, Po(max) = 1 W, answer the…

Q: For the circuit below, determine the diode voltages VD1 and Vp2, diode currents Ip1 and Ip2, and…

A: We need to find out voltage and current in the given circuit .

Q: a) To what value R must be adjusted in the following circuit to make IZ = 70 mA. Assume VZ =20 V at…

A: The diodes are made of semiconductor materials. Silicon and germanium are common semiconductors for…

Q: Figure 1 shows a circuit for energizing inductor L and removing the stored energy without damaging…

A: Voltage across inductor is, VL=LdiLdt Power across inductor, P=VLIL Power across inductor, P=VZIZ…

Q: 2. Sketch the output V and determine the DC level of the output signal for the given network below.…

A: The given circuit is full wave rectifier which means for both positive and negative half cycle of…

Q: Using the second approximation with VT=0.7V for both diodes, what are the states of D1 and D2…

A: When power supply 1 of 7 V is on and power supply 2 is off then no current flows flows through the…

Q: IRL RL In the circuit using a Zener diode above, given that V, = 10 V, R 3.7 KQ, R = 6.8 KQ, and the…

A: Given circuit: Vi=10 VR=3.7 kΩRL=6.8 kΩVZ=5 V

Q: Consider the diode circuit shown in the figure, where R, = R2 = 1 kN. R1 o V. Vs(t) Ip R2 VB /hen VB…

Q: diode whose internal resistance is 20 ohms is to supply power to a 1000-ohm load from a 110V(rms)…

Q: SAS 3, ACTI VITY 3: ad For the Zener diode network shown in deter mine VL, UR, Iz, and Pz. VR | 1…

A: Note : Input voltage is not i am considering input voltage as 16 V and solving the question. -

Q: Design the network of below to maintain V L at 12 V for a load variation (I L) from 0 mA to 200 mA.…

Q: . Consider the diode circuit shown in the figure, where R1 = R2 = 1 kN. v. v.(t) When V3 = 4 V and…

Q: Q2- For voltage source Vs = 50V, calculate the allowable range of load resistances for the Zener…

A: Given data, VS=50 VVZ=14 VPZ=5 Wrz=0 In the given figure, Calculating current in the zener diode,…

Q: Q2) Explain the working of zener diode on both forward and reverse bias. From the circuit in the…

A: Zener diode- Zener diode is highly doped diode 1:10^5. It is always fabricated with Si. Because…

Q: Example3: The forward voltage drop of a power diode is VD= 1,2 V at Ip = 300 A. Assuming that n = 2…

A: Need to find reverse saturation current

Q: The Zener diode shown below, is specified to have Vz-20V at Izr, IZK = 0.1 mA, IzT =17 mA, and r, =…

Q: Q2. An ideal single phase source 240V, 50HZ, supplies power to resistive load R=10 Q via a single…

A: In this question we need to find the average ,RMS current and power rating of diode.

Question

For the Zener diode network of figure below, if R = 1 kn, R, = 5 kN, V; = 24 V, Vz = 15 V, PzM = 60 mW;
a) determine V,, VR, Iz, and Pz.
b) Is the design of the circuit correct, why?
R
Vz
PzM
VL
RL

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the circuit shown in Figure, consider Ideal diodes. If Vs = 19sin wt, Vb = 4 V, the minimum value of output voltage is: Vout at of estion Vs Vb Oa. -4 V Ob. -15 V Oc. -19 V Od. 4 V
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
A simple voltage regulator is shown in the figure below. The source voltage Vs varies from 8 to 12 V, and the load current i, varies from 50 to 150 mA. Assume that the Zener diode is ideal. Determine the largest value allowed for the resistance Rs so that the load voltage v, remains constant with variations in load current and source voltage. Determine the maximum power dissipation in Rs. Rs Vs = 5 V VL
In the circuit shown in the figure, diode voltages are given as 0.6V and rD = 100 ohms. When point B is open circuit AIf + 5V is applied to the point of application, drawing the shape of the circuit formed and calculating the currents passing through the resistors.calculate.
Derive the current equations for the circuit shown below, using the labels as shown.Note that rz here is a model of the parasitic imperfection of the Zener diode.a) IL = ?b) II = ?c) IZ = ?d) What impact does rz have on VL?
An ac voltage of peak value 20v is connected in series with a silicon diode and load resistance of 5002. if the forward resistance of diode is 102 find: i- Peak current through diode. ii- Peak output voltage. ii- What will be these values if the diode is assumed to be ideal (Vdiode =0)?
A diode whose internal resistance is 20 ohms is to supply power to a 1000-ohm load from a 110V(rms) source of supply. Calculate the peak load current, dc load current. and determine the percent regulation from no load to the given load. a.) Peak Load Current= 120.8mA; DC load current=25.5mA b.) Peak Load Current= 133.3mA; DC load current=29.4mA c.) Peak Load Current= 144.3mA; DC load current=34.7mA d.) Peak Load Current= 152.5mA; DC load current= 48.5mA
In the circuit given in the figure, since Vi is a square wave with a frequency of 1 kHz and an amplitude varying between +5V and -5V; Vi and Vo voltages one after the other and in scale; a) Draw with Zener diode is not active ? b) Draw with the Zener diode on? (Assume the diodes in the circuit are ideal)
A shunt regulator employs a zener diode for which VZ = 10.1 V at IZ = 10 mA while VZ = 10.2 Vat IZ = 20 mA. The available supply voltage (VS) is 15.0 V, R = 300 ohm, and the load resistance(RL) =1.0 kohma) Find VZ0 and rz.b) Calculate the output voltage (VO).c) Determine the line regulation (ΔVO/ΔVS).d) Using the line regulation obtained in (c), determine the values of the output voltage (VO) if thesupply voltage (VS) is increased from 15 V to 15.1 V.
The Zener diode shown below, is specified to have Vz=20V at IzT, IZK = 0.1mA, IzT = 17 mA, and r, = 14 N. Vcc = 30V. 1) Replace the Zener diode with its Model. 2) Find the current I with no Load. 3) Find Vo with no Load when VCC = 30V. 4) Find RL Min. AV* 30V R 2000 Vz = 20V 6.8-V Vo RL zener
a. Using standard resistor values, what value of R1 is needed to achieve 1.18V ±0.01V at Vout? b. Using the R1 value chosen in (a) part, what happens to the voltage Vout when a load resistance of 10K is added (between Vout and ground). c. What is the minimum value of load resistance required for correct operation Zener diode is used in place of si diode. Or you can assume zener current according to requirement Answer it i will rate
Zener voltage, VZ = 6.1V and incremental resistance, rz = 0 a) Determine the value of Ri such that the Zener diode remains in breakdown if the load current varies from IL = 20 to 200 mA and if the input voltage varies from VI = 8.6 to 10V. Assume IZ(min) = 0.1IZ(max). b) Determine the power rating required for the Zener diode and the load resistor. c) If the position of Zener diode were changed to be in forward bias region, will the voltage regulator still work properly? Justify your answer