For the circuit shown below, calculate: - 1. The input impedance of the circuit 2. The output impedance with load 3. The total voltage gain 4. The total current gain 24 V +Vcc 22 k Ohm 8k Ohm 15 k Ohm 6k Ohm 3.3 M Ohm Darlington ß1=50 B2=50 ß1=100 1 uF B2 =80 3.3 k Ohm 1k Ohm 1.5 k Ohm 1.2 k Ohm 2k Ohm 470 Ohm

For the circuit shown below, calculate: - 1. The input impedance of the circuit 2. The output impedance with load 3. The total voltage gain 4. The total current gain 24 V +Vcc 22 k Ohm 8k Ohm 15 k Ohm 6k Ohm 3.3 M Ohm Darlington ß1=50 B2=50 ß1=100 1 uF B2 =80 3.3 k Ohm 1k Ohm 1.5 k Ohm 1.2 k Ohm 2k Ohm 470 Ohm

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
Q1: Draw the d.c load line for the circuit shown in figure. NO SIGNAL VBB Vcc= 12.5 V www Re=2.5 k2
2. The circuit given below is using a transformer of 230V/30V. The load resistance is 10KS. Find Vin (rms and peak values), Vdiode and VLOAD (Peak and dc values). Draw the input and output voltage waveforms. (Si diode) Vin: Vin rms= Vin peak = VDIODE Vdiode = 4 Vin VLOAD: VLOAD Peak =. Load VLOAD VLOAD DC= 2031 Supply wwwwww
For the following zener clipper draw the output waveform Vz1 = 5V, Vz1 = 7V VK = 0.8v lkn ISV V₁₂ 5V 2, 72. -5V Q2 Determine The Output Waveform And Calculate The current and PIV 1kQ 1kQ 10 V 10 si www www Q. For the circuit shown in Figure below (1),find the maximum and minimum values of zener diod current. Live 5 ΚΩ www I IL 15 80-120 V 10 ΚΩ LIR 101 102 1015 S Ne 1 k0 www Iz 50 V U2 -ot V. Fumal inash
6. The R-C circuit has a resistance of 100 ohms and a capacitive reactance of 150 ohms are connected in series across a A.C. voltage source. If a current of 0.9 A is flowing in the circuit determine (a) Power factor (b) Active power (c) Reactive power.
In the circuit shown in the figure, Rs = 1.88Kohm, R1 = 1201.67Kohm, R2 = 5.72Kohm, R3 = 59.80Kohm, R4 = 15.44Kohm, R5 = 3.15Kohm, R6 = 1.05Kohm, Ry 94.19Kohm, VCC1 = 11.00V, %3D VCC2 = 10.00V, Beta1= 126.00, Beta2= 248.00, VT = 25mV, IVBE| = 0.7V and OPAMP is ideal, calculate the absolute value of the voltage gain (IVO/VS|) of the circuit relative to the source (The %3D result will be positive).
The voltage regulation can be equal to zero when: O The t and current is not too high. OThe p.f. is leading p.f. for any possible current. OThe p.f. is lagging p.f. for rated current.
For the circuit shown in figure. For the circuit shown in Figure IF IB= 40 MA , VBB= 6v, RE= | Ksr, P= 80o FRc Re VeB Re The value of IE is . . mA..* О 3.24 O 4.24 O 5.24 O 6.24 O 1.24 O 2.024 The value of RB is . Kohm.. * O 52.5 O 55.5 O 47.5 O 57.5 O 25.5 O 48.5 The value of Vce is .. volt. NOTE: USE Rc= 3 Kohm, and Vcc= 15 volt. * O 5.04 O 2.04 1.04 O 4.06 O 4.04 O 3.04 O O O O O ООО О о
2. For the circuit shown in the figure below find the following a. Write the name of the circuit....... b. Find the value of IB, IC and VCE c. Draw the DC load line d. Mark the operating point or Q-point [assume ß-100 and VBE=0.7V] 23-202 RB www 270 KQ VBE +Vcc 20V Rc 2.0 K VCE RE=1 KQ
Q2:-Find the output voltage Vo . Ry B2HF 100 kQ + 100 mV rms,
For the FET equivalent circuit in Figure 1, what is the value of the input impedance? Why is it open-circuited? Explain your answer? Go 8mVgs So Figure 1
H.w For the circuit show n figure ca Iculate the expre ss ion of tne assume t he in i tial value of in ductor .initial value of cap acit or is zero o'lf th o'5 F