Flow occurs over the spillway of constant section as shown in Figure 1. Given that y1 = 4.2+(Reg.No/100) m and y2 = 0.7+(Reg.No/100) m. Determine the resultant horizontal force on the spillway per meter of spillway width (perpendicular to the spillway section). Assume ideal flow.

Q: The both sides of a rectangular sluice gate are partly submerged in water as shown in Figure 3.4. If…

A: h1=3m h2=6m

Q: A vertical rectangular sluice gate of 5m width is held by supports on its both sides and lowered…

A: A vertical sluice gate is given, and it has been asked in the question to determine the total…

Q: Q1-10: There is a sluice gate at upstream section of 3.5 m wide rectangular channel (see below…

A:

Q: water flows at a rate of 0.5m/sec round a 50 contracting pipe bend which lies in a horizontal plane.…

A:

Q: 2)Pipe A,600mm in diameter and 3000m long draws water from reservoir "A" with water surface…

A: As per the given information we have to calculate the required unknown.  The discharge through pipe…

Q: For downward real flow in offset water pipe shown, find: The required pressure at D 1. 2. Determine…

A: Given, PA = 50 kPa L = 8 m  D = 20 mm or 0.02 m  Q = 0.2 L/s or 0.0002 m3/s

Q: The chute has a cross-sectional area of 0.03 m² at A and B. If the flow is 0.4 m³/s at B and the…

A:

Q: The inclined circular (D = 3,57 m.) gate shown below retains a liquid with SG = 3.64 on one side.…

A: Calculate the depth of centre of pressure from the free water surface. Then calculate the pressure…

Q: Question 4. The flowrate of the flow is 0,2c m³/s in a pipe placed on a horizontal plane. The pipe…

A: Given Q= 0.2 m3/s D1=0.4m D2=0.8m P1=80 kN/m2   Fx=force component in x direction Fy=force component…

Q: The flowrate of the flow is 0,20 m³/s in a pipe placed on a horizontal plane. The pipe diameters are…

A: When water flows through pipe, a force is exerted on the pipe by water. To calculate force on pipe…

Q: Air Question 5. 1,2 m wide AB gate is articulated from point A shown in the figure. The heights of…

A: The given figure is shown below:

Q: Water flowing in a horizontal 20-cm-diameter pipe at 8 m/s and 300 kPa gage enters a 90° bend…

A: Given Data: The diameter of the pipe at section 1 is, d1=20 cm The velocity of water at section 1…

Q: Water ilt in 150 ft e Tunnel 30 ft-

A:

Q: A steady, two dimensional, incompressible flow field is represented by u = x + 3y + 3 and v = 2x - y…

A: Given- flow fields-u=x+3y+3v=2x-y-8

Q: ) For the overflow of ogee spillway as shown in fig. (1), determine the dynamic force on the curved…

A:

Q: Q.4.A..A (3m) high, (5m) wide rectangular gate is hinged at the top edge at (A), and is restrained…

A:

Q: Water flows in a wide channel at Fr=4.5 and y1 = 2.40 m. If the flow undergoes a hydraulic jump,…

A:

Q: Determine the total hydrostatic force (kN) in an inclined, rectangular gate 1.68 m width with oil on…

A:

Q: Problem 6. The 1.2 m - diameter log with specific gravity of 0.8 is 3.0 m long into the paper. The…

A:

Q: Water flows through a pipe AB 1.2 m diameter at 3 m/s and then passes through a pipe BC 1.5 m…

A: Given: The diameter of the pipe AB is 1.2 m. The velocity of flow in pipe AB is 3 m/s. The diameter…

Q: Problem 2. In reference to the figure, gate XY is 1.20m wide and 1.40m long., If the liquid in the…

A: To determine total hydrostatic force "F" acting on the gate its line of action "h₂" vertically from…

Q: Determine the total hydrostatic force (N) in an inclined, rectangular gate 0.14 m width with oil on…

A:

Q: Problem 6. The 1.2 m - diameter log with specific gravity of 0.8 is 3.0 m long into the paper. The…

A:

Q: horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5…

A:

Q: Calculate the magnitude and direction of the force exerted by the T-junction shown if discharges are…

A: The formula to calculate the velocity in the pipe is given by, v=QA Here, v is the velocity, Q is…

Q: Water flows in the bend shown in figure at a rate of 5 m3/s, and the pressure at the inlet is 650…

A: To solve this problem, we will use Bernoulli equation. Therefore, we will calculate all the terms…

Q: Determine the elevation head, pressure head, total head and head loss at points A, B and C.…

A: Given Diagram:-

Q: Liquid 1 Liquid 2 h3 h1 h2

A: To find the pressure at the center of pipe using a manometer , we need to take a datum about which…

Q: Try making the flow net for the following diagram. Given: H1= 6m H2= 1.5 m D= 8m D1= 4m Draw a flow…

A:

Q: A 30° 2.5m Water hinge B L = 2m In the figure shown, a quarter circle gate AOB is hinged at point B.…

A:

Q: 6. Fluid speed before the hydraulic jump is a) Critical b) Supercritical c) Subcritical d) Dynamic

A: Answer is (b) super critical

Q: An open horizontal tank 2 m high, 2 m wide and 4m. long is full of water. a) How much water is…

A:

Q: Assuming unit wt. of water = 9.79 kN/m³ O Compute the horizontal component of the hydrostatic force…

A:

Q: 3.a. Define the hydraulic jump with the flow conditions before and after it. Show that the energy…

A: Hydraulic jump- when the flow condition changes from supercritical (Fr>1) to subcritical…

Q: A 3-ft-diameter welded steel pipe (f = 0.0135) is carrying 15 cfs of water at 60°F. At this…

A:

Q: Question 4. The flowrate of the flow is 0,20 m²/s in a pipe placed on a horizontal plane. The pipe…

A: Solution Given Data Flow Rate Q=0.20 m3/s Pipe Diameter D1= 0.41 m Pipe Diameter D2=0.28 m Gauge…

Q: 2- A semicircular 30-ft-diameter tunnel is to be built under a 150-ft-deep, 800-ft-long lake, as…

A: Solution Given data The depth of the lake hd=150 ft The length of the lake l=800 ft The dia of…

Q: 6.32. Flow occurs over the spillway shown. De magnitude and direction of the horizontal force ex…

A: Y = 4’y = 0.6’ From continuity equation w = width Q = YwV = ywv4V = 0.6vV = 0.15v As we know that…

Q: Figure shows that the pipe flow of 1200 m^3/day, is driven by pressurized air in the tank. 20m T…

A:

Q: Three pipes are in parallel. The total volumetric flowrate through the network is 2.15 cumecs. If…

A:

Q: Q.3. Water flows in a (1.2 ft) diameter pipe at a flow of 13 ft'/sec. The pipe bend changes the…

A: Given:- pipe diameter =1.2 ft flow =13 ft3/sec Pressure at point 1 = 88 psi Q=13 ft3/sec angle alpha…

Q: The channel is subjected to a shear of V = 20 kip. (a) Determine the shear flow at point A. 1.5 in…

A:

Q: Underground water is pumped through a 10,ab (cm) diameter pipe that consists of a 2,ab (m) long…

A: Given Data: a=7 b=2 w=12kg

Q: A vertical triangular gate with a horizontal top base that is 3m wide is 6m high. It is submerged in…

A:

Q: If the friction headloss is significantly changing in a pipe flow, which of the following is most…

A: Given data in question  Pipe flow Friction head loss To be discussed  Friction headloss…

Q: A vertical pipe 3 ft in diameter and 30 ft long has a pressure head at the upper end of 22 ft. of…

A:

Q: A tank 13 ft deep and 5 ft wide is layered with 6 ft of oil (y = 50.0 lbf/ft3 ), 5 ft of water, and…

A: Given "

Spillway design

A spillway is the overflow portion of the dam that carries the surplus discharge flow from the reservoir to the downstream, that is, it carries the flood water safely downstream, which is enough to be stored in that reservoir. Therefore, it acts as a safety valve for the dam because many failures of the dam arise due to the incorrect design of the spillway.