Find all types of power losses (the second photo shows the types of power losses)The weight of the car is 800 KgThe weight of each person is 75 KgYou may assume any missing parameters you need in the design appropriately (e.g., the rolling-resistance-power, air-resistance-power, the DC motor's parameters, ....etc) P convP. Tapp mPin = VrLEAA=Tind mMechanicalStraylossesCorelosseslossesR losses(b)Armature losses (1PARA)OField losses (12FRF)Brush losses (VpplA)Every thingelse!FrictionHysteresisEddy currentWindage It is required to design a DC motor to run a small size electric vehicle to beused inside an airport building to help the transportation of needy people.The vehicle is supposed to carry a maximum of 4 persons at the full loadspeed of 60 Km/hour. The engine is driven by a 200 V battery systemcapable to energize the motor for 120 Km before being recharged. Theefficiency of the motor must be between 85 to 90 percent. The motor shaftdiameter is expected to be within (0.2 to 0.4 m). Give the size of thebattery required in AH (Ampere Hour). Choose and estimate all the designcharacteristics of the motor. Finally display all the power flow diagramresults including efficiency and speed regulation of the motor. State allassumptions taken.

v=60 km/hrv=60×10003600v=16.66 m/secV=200VDistance to drive=120 kmTime required to cover the…

Find all types of power losses (the second photo shows the types of power losses) The weight of the car is 800 Kg The weight of each person is 75 Kg You may assume any missing parameters you need in the design appropriately (e.g., the rolling-resistance-power, air-resistance-power, the DC motor's parameters, ....etc)

Find all types of power losses (the second photo shows the types of power losses) The weight of the car is 800 Kg The weight of each person is 75 Kg You may assume any missing parameters you need in the design appropriately (e.g., the rolling-resistance-power, air-resistance-power, the DC motor's parameters, ....etc)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

Explain the prime mover in diesel plant and it's energy conversion
1. Check any DC power sources in most large body aircraft. Choose all the correct answers. 2. These power sources supply 28V in most large body aircraft. Choose all the correct answers.
I need this as fast as 20 minutes max please..
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
0.1 Give a short answer for only Six of the following 1. Explain the construction of turbine meter and mention for what we use it. 2. Mention the Applications of Pyroelectric sensors. 3. Explain briefly Hall effect sensor's application by measuring the fluid level in a container. 4. Explain how could we use potentiometer to measure linear displacement and angular displacement. 5. According to electrical circuits and electric fundamentals what's the evident difference between Eddy current proximity sensor and Inductive proximity sensor? 6. What's the purpose of putting an inner track with only one hole in optical sensor? 7. What's the reason behind using Wheatstone bridge with strain gauge sensor?
A chair transporter is designed to move 900 skiers per hour from base A to summit B. The average weight of a skier is 160 lb and the average speed of the transporter is 250 ft / min. Determine, a) the average power required, b) the required capacity of the motor if the mechanical efficiency is 85 percent and an overload of 300 percent is allowed
5-Synchronous generator ,50 HZ have induced emf of 1.2 pu is connected to an infinite bus of 1 pu voltage .The maximum power that can be transferred if the reactance of generator is 0.2 pu and the rest of the system have a reactance of 0.4 pu is. a) 3pu b) 2pu c) Ipu d) 4pu
For a system if the value of peak overshoot is 22 %, then the value of damping ratio ő is
ii) A 6.5 A, 200 V energy meter on full load unity power factor test makes 80 revolutions in 595 seconds. If the normal disc speed is 483 revolutions per kWh. find a) Actual energy b) True energy c) Error d) Percentage error
The principle of operation of moving coil meter is similar to DC motor. 1)True 2)False
1) In a certain circuit battery is draining out 5 times more quickly than expected for normal operation what could be the possible cause for this and how did you conclude it. 2) Why AC current is preferred over DC current for high power electrical circuits. 3) Initial current across a capacitor connected across a DC source is huge and initial voltage is zero, explain why this is so. 4) Explain the working of AC generator in your own words. 5) In a Wheatstone bridge circuit a student connects a motor in place of galvanometer and is trying to find unknown resistance using formula when he adjusts variable resistor and observes that motor is no more rotating. Do you agree with his technique or not explain with reasoning. 6) What does a negative value of loop current indicates in Mesh Analysis and Method of Branch Currents, and also comment on if there a way to avoid this negative sign appearing for loop current's value.
SHOW COMPLETE SOLUTION An elevator is designed to transport 120 passengers per hour from the 1st floor to the 10th floor. The average mass of a passenger is 75kg and the average speed of the elevator is 130kph. Determine: A. The required capacity of the motor if the mechanical efficiency is 90% and if a 250 percent overload is allowed. B. The average power required