Figure below shows a steam jet refrigeration system that produces chilled water in a flash chamber. The chamber is maintained at a pressure by the steam ejector, which removes the vapor generated by entraining it in the low-pressure jet and discharging into the condenser. The vacuum pump removes air and other non-condensable gases from the condenser shell. For the conditions shown on the figure, determine the make-up water and cooling water flow rates in kg/hr.

Figure below shows a steam jet refrigeration system that produces chilled water in a flash chamber. The chamber is maintained at a pressure by the steam ejector, which removes the vapor generated by entraining it in the low-pressure jet and discharging into the condenser. The vacuum pump removes air and other non-condensable gases from the condenser shell. For the conditions shown on the figure, determine the make-up water and cooling water flow rates in kg/hr.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

28. A centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specifie volume is 12.6 and final specific volume is 3.25 If the inlet suction lirfe is 4" I.D. and the discharge line is 2.5" I.D. Determine ft-lb (a.) The change in flow energy between the boundaries in- min Ib (b.) the mass flow rate in and min (c.) the change in velocity in fps.
identifuy the limitations that exist within different types of water turbine
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Ideal turbine work (KW). Ans.____________________________ Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.____________________________ Pump work in KW. Ans.___________________________
A process in a plant is to he revised such that the airflow rate through Si system will increase from 8000 cfm to 10,000 cfm, The existing fan runs at 1600 rpm and provides 6,0 in, H2O SP. Estimate the new speed required for this fan and the new SP.
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Combined work (KW) . Ans.____________________________ Combined steam rate in kg/KW-hr. Ans.___________________________ Actual heat rate( KJ/KW-hr). Ans.____________________________
1) A singe acting, twin cylinder, ammonia compressor with bore equal to stroke is driven by an engine at 250 rpm. The machine is installed in a chilling plant to generate 700 kW of refrigeration at -18C evaporating temperature. At this temperature, the cooling effect per kg mass is 1160 kJ. The sp volume of vapor entering the compressor is 0.592 m³/kg. Assume 85% volumetric efficiency. Calculate the bore in mm.
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Pump work in KW. Ans. Ideal heat rate in KJ/KW-hr. Ans. Rankine engine efficiency (%). Ans. Cycle thermal efficiency ( %). Ans
Condenser 30 c „Flash Chamber Pi Evaporator OC & 50 kW For a 2-stage ammonia compression system, determine: 1. Draw the PH diagram showing the condenser, evaporator, & compressor discharge temps, intercooler pressure, all enthalpies & compressor suction specific volumes, m/kg 2. Compute the intercooler pressure in Bars & equivalent Ti in °C 3. Compressor discharge temps T: & T4 4. Mass of refrigerants m:, ms & m: in kg/sec 5. Compressor power Wi, W & total W- in kW & HP 6. Compressors PD with equal volumetric efficiency 80%; m/s 7. Condenser capacity, kW 8. Using a single stage compression, calculate & compare the power of the compressor/s in kW & HP
i need some one explian the TS digram Rankine Cycle
20 4) 1300- T=-40°C -30 1400 -20 1350 OL- 2. 09- 1250 1200 1150 <- -50 1450 1100 09 08 06 00, PRESSURE, MPa 006 2 కికి కి work of the compressor if the compressor efficiency is,70%. as saturated liquid. Calculate the actual volumetric efficiency and the brake pinbn pejemes 2, 0.1. and condensing temperature is 50°C. The refrigerant leaves the cond the capacity to be 8 tons when the suction conditions are 0.1 MPa and -20°C 20 0.70 F0 = x Catalogue data for R-134A compressor with a displacement of 75 L/s show 0.3 10 0.80: -06'0 Problem: - 00'L CO 0.5 0.6- 4, 1.10 - PLEASE.. the full solution of this problem and needs it to be clear solution needed). I need to see the enthalpy graph in the chart below. I need 8-1.30 - 1.40 1.20 0.7 0.8- 2. 0.9- Instruction: I want the t-s diagram , p-v diagram and (schematic if Saturated Vapor 09 08 06 1.60- 100 110 1.70 - 1.80 T = 160°C +170 - 180 06 140 150 = 2.30 kJ/(kg-K) enser 001 350 R-134a 00s (1,1,1,2-totrafluoroethane) Reference state: h= 200.0…
The air outside is 40 C and 60% r.h. I want torun an air conditioner to cool it to 15 C. The deliver rate should be 1000 m^3/min. What is Q and the rate at which water condenses (if any)?
Q. Mention the main reguirements of a steam condensing plant.