Figure 1 shows a differential amplifier. Assume that all transistors are identical. = 180, V₁=0.026 V and VBE = 0.7 V. ВЕ a) b) Show that the d.c. bias current to the differential pairs is Iccs = 0.6 mA. Calculate the d.c. voltages at the output terminals V₁ and Vo2. 5kQ 9.6kΩ +12 V 오 Vil 6kQ O 0|1₁ 20-411 Figure 1 Vo2 1 ccs 12kQ2 6kQ Vi2 옿

Figure 1 shows a differential amplifier. Assume that all transistors are identical. = 180, V₁=0.026 V and VBE = 0.7 V. ВЕ a) b) Show that the d.c. bias current to the differential pairs is Iccs = 0.6 mA. Calculate the d.c. voltages at the output terminals V₁ and Vo2. 5kQ 9.6kΩ +12 V 오 Vil 6kQ O 0|1₁ 20-411 Figure 1 Vo2 1 ccs 12kQ2 6kQ Vi2 옿

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine VB, VE, VC, VCE, IB, IE, and IC in Figure. The 2N3904 is a general purpose transistor with a typical BDC 200 Vcc +30 V WWII VCE VB R₁ • 22 ΚΩ IC(mA) Chọn... * Chọn... * IB(UA) Chọn... * IE(MA) Chọn... ◆ Chọn... * Chọn... * Chọn... * VE VC R₂ ´ 10 ΚΩ www Rc 1.0 ΚΩ 2N3904 PDC=200 RE 1.0 ΚΩ
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
The Pinch off voltage for N- Channel JFET is -3V, maximum saturated drain current 8mA and the value of VGS is -1.5 V. Calculate drain current, a. 18 mA b. 2 mA c. 2.5 mA d. 4 mA
The Pinch off voltage for N-Channel JFET is -3V, maximum saturated drain current 8mA and the value of VGS is -1.5 V. Calculate drain current, a. 4 mA b. 2.5 mA c. 2 mA d. 18 mA
H. W. of Lecture L(7-2)C 1. Determine whether or not the transistor in figure above is saturated for the following values: Boc = 125, VBB = 1.5 v, Re = 6.8 kO, Rc = 150 Q and Vcc = 12 V. Rc1.0 kll R Vcc 10 V Bpc=50 10 ks2 VBB 3 V 2. What value of Rc in the figure above will it take to have a voltage gain of 50? Rc 1.0 kn RB Gut Vcc- V, 100 mV
Questiona. In an experiment the voltage required for the device is 9V dc but unfortunately the transformer available is of 220-6 Vdc. Design a circuit which can power the device (use only methods that we have studied excluding Zener diode)b. Explain the behavior of the following circuits if the input signal is triangular wave of peak voltage 5V and the biasing battery of 3V
EHide bla This course Determine Vx and the mode of operation of the PNP transistor shown in the figure below. Assume Is = 2.5x106 A,B- 50, VA =, and Rc = 0.1 KO. Vec 2 V EX 1.2 V- Re幸 Select one: O a.1.153 V. Active Mode O60577V. Active Mode Oc 023 V. Active Mode d. None of these Oe 2306 V Saturation Mode For the circuit shewn in the figure below. assume l = 3 107A V= 26mv. B= 100, and V = The value of r-5
c. For the circuit shown in Figure, determine lc and VCB. Assume the transistor to be made of Silicon. Ic RE=1.6 kn Rc=1.1 kn EE=8 V Vcc= 20 v
To a measurement range of -4 to 6 V, apply a 4-bit analog-to-digital converter. a- Identify the assigned voltages to each of the bins. b- Determine the voltage that will be assigned to a measurement reading -3.25 V. Calculate the percentage ADC error. c- Determine the voltage that will be assigned to a measurement reading 4.11 V. Calculate the percentage ADC error.
As a maintenance engineer in a semiconductor company, you are given a task to replace the current version of dc-biasing circuit for a faulty tester machine. This dc-biasing circuit used an n-channel JFET as shown in Figure 2. Re-design a new dc-biasing circuit using an n-channel D-MOSFET that can produce a similar output current, IDQ as the previous circuit. Your tasks are: (i) Calculate the operating point (IDQ and VGSQ) of the dc-biasing circuit in Figure 2. Then sketch the JFET network transfer curve (ID and VGS). (ii) Without changing the circuit configuration, calculate the values of source resistor, RS and RB to achieve this objective. Determine the commercial value of the new RS and RB.  For cost reduction reason, the values of RD, RA and VDD should be maintained.  The chosen D-MOSFET has a maximum drain current of 8 mA and gate-source cutoff voltage of – 15V.  The new RS value should be 3 times larger than the old RS used in the JFET network to compensate for the high…
A resistor Ra is in series with a voltage source Va. Draw the circuit. Label the voltage across the combination as v and the current as i. Draw and label the volt–ampere characteristic (i versus v).
4) Consider the clamping circuit below, assume Vref=3 V and Vin=5sin(wt) ..Draw the output voltage waveform. Clearly mark the max and min of the voltage.. Vref