Example 4. Flow between two reservoirs. Water at 10°C flow from a large reservoir to a small one through a 5-cm-diameter cast iron piping system shown in figure (6). Determine the elevation 2₁ for the flow rate of 61/s. Z₁ = ? @ Sharp-edged entrance, K₂ = 0.5 Standard elbow, flanged, K₂ = 0.2 = 4 m Gate valve fully open K₁ = 0.3- -Exit, K₂ = 1 (Answer. 27,9 m) 20 D = 5 cm -System boundary 9 m 80 m Figure 6:

Example 4. Flow between two reservoirs. Water at 10°C flow from a large reservoir to a small one through a 5-cm-diameter cast iron piping system shown in figure (6). Determine the elevation 2₁ for the flow rate of 61/s. Z₁ = ? @ Sharp-edged entrance, K₂ = 0.5 Standard elbow, flanged, K₂ = 0.2 = 4 m Gate valve fully open K₁ = 0.3- -Exit, K₂ = 1 (Answer. 27,9 m) 20 D = 5 cm -System boundary 9 m 80 m Figure 6:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A water siphon having a constant inside diame of 3 in. is arranged as shown in the figure below the friction loss between A and B is 0.8V²/2 wh is the velocity of flow in the siphon, determine flowrate involved. Assume a = 4 ft, h = 12 ft. D-- B a h
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the tank is 0.028 m^3/ sec. Determine the minimum height, h, of the water tank under the assumption that (a) minor losses are negligible, (b) minor losses are not negligible. 3 m Figure No.3 Kentrance = 0.5 h The pipe is plastic of 15 cm diameter and (e/D=D0) 1.8 m (2) Main line 450 m with 15 elbows of 90 degree
4.80 Water (p = 62.4 lbm/ft³) flows from the large orifice at the bottom of the tank as shown. Assume that the flow is irrotational. Point B is at zero elevation, and point A is at 1 ft elevation. If VA = 4 ft/s at an angle of 45° with the horizontal and if VB = 12 ft/s vertically downward, what is the value of PA - PB? Answer B Vertical Problem 4.80 45°
Show the necessary figures (if applicable) 2.3) A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
2. Consider the piping network shown. The pressure heads at points A and B are 80m and 52m, respectively. If the Hazen- Williams Coefficient for all pipes is 110, calculate the flowrate in each pipe. 1 A B 3 2 L₁ = 3000m L2 = 2600m L3 1300m D₁ = 300mm D₂ = 250mm D3 = 200mm
Water in the reservoir is used to control the water pressure in the pipe at A. Take pHg = 13550 kg/m³ and p = 1000 kg/m³ Neglect the diameter of the pipe. (Eigure 1) Figure AQ B E h 400 mm C 150 mm 100 mm 200 mm Mercury pe he Y Part A If h= 140 mm, determine the gage pressure in the pipe at A when the mercury is at the elevation shown. Express your answer to three significant figures and include the appropriate units. PA 76.8 Submit 4 Provide Feedback kPa CINC Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining
Three reservoirs are connected.by a pipe system as shown in the a) figure and all the length and diameter of each pipe are as indicated. Find the discharge through the each pipe and the piezometric head at the junctioni. Take f= 0.02. L1=800m- D1=0.3m A L2=1000m D2=0.2m В 60m 40n L3=800m D3=0.15m C 3m
A pump draws water from reservoir A and lifts it to reservoir B as shown. The loss of head from A to 1 is 3 times the velocity head in the 150mm pipe and the loss of head from 2 to B is 20 times the velocity head in the 100mm pipe. When the discharge is 20 liters/sec. Compute the pressure head at point 1 and 2. B EL240m ELO 150 mm EL-20m • ura 001
A/ In the pipe systems show, find the distribution of flow, with a friction factor of 0.0165. Assume that minor losses can be neglected. (use Darcy-Wiesbach) B/ If the pressure at first point (Qin) =580 KPa, then find the pressure at point E. Pipe Đia.-m Length-m 04 ms m3's A 0.658544 1 AB 0.305 500 G 2 BC 0.205 300 3 AC 0.505 400 CF 0.305 350 Loop 2 FG 0.305 300 1026M5 mas 6 GA 0,405 300 7. 05 mas 8. CD 0.405 400 Loop 1 DE 0.405 300 9 EF 0.205 500 B. 10.4 m3s 04 ms Loop 3 0.31598 m3s D E 0.3 m3s
3. Obtain the gage pressure at the center A of the pipe shown. Ignore surface tension effects. Given: Liquid 1 S.G. = 1.5 Liquid 2 S.G. = 3.2 hi = 15 cm h2 = 30 cm h3 = 75 cm a. 589 Pa с. 452 Ра d. -452 Pa b. -589 Рa Liquid 1 Liquid 2 X1 h,
2. A 20mm diameter commercial steel pipe, 30m long is used to drain an oil tank. Determine the discharge when the oil level in the tank is 3m above the exit of the pipe. Neglect minor losses and assume f = 0.12. D=20mm, L=30 m, f-0.12 3 m