Estimate the tile work, ceiling and paint of a two storey residential building with the 14.3m x 8.5m total floor area

Q: Chapter 5, Problem 5/049 (video solution to similar problem attached) Determine the x- and…

A:

Q: Derive the Conditions for Ecnomical and Effective Circular Section of having depth of flow above…

A:

Q: Say a W12x45 is not safe against rupture, what other design. considerations should be explored to…

A: A section W12 x 45 , if it is not safe for rupture, it means that there is a net section failure…

Q: 3 -1 m- 'С -3m-

A:

Q: determine the true area of land surveyed

A: This question is from Surveying

Q: Determine the constant a so that the vector V = (x+3y)i + (y-2z)j + (x+az)k is solenoidal.

A: in this question a vector is given V and we are asked to find constant a  it is given that vector is…

Q: Q1: Choose the correct answer 1. Lateral earth pressure (passive or active) is a dependent of A. the…

A:

Q: How does moisture impact tension and compression strength in composites?

A: Composites: A composite is a multiphase material formed from a combination of two or more materials…

Q: an oil refinery is located on the north bank of a straight river that is 2 km wide. a pipeline is to…

A: Given :- 1)Cost of laying pipe over the land to point P =$400000/km  2)Under the river to…

Q: ..s) The beam shown is fixed at A and to be supported by rod BC at B. The beam carries a uniform…

A:

Q: 2. Design the salient dimensions of a syphon well drop for the following particulars : Fall = 3.8 m…

A:

Q: AN ALUMINUM SEGMENTS HAVING A DIAMETER AND LENGTHS SHOWN IN THE FIGURE. IF E = 85 KPa, COMPUTE THE…

A:

Q: What happens when flow enters a long pipeline from a large reservoir.

A:

Q: Vehicles arrive at a single toll booth beginning at 7:00 A.M. at a rate of 8 veh/min. Service also…

A: The given data is: Vehicles arrive at a single toll=7:00 A.M Rate of arrival=8 veh/min Service start…

Q: Knowing that the coefficient of static friction between the tires and the road is 0.80 for the…

A:

Q: TWO SOLID CYLINDRICAL RODS ARE JOINED AT B AND LOADED AS SHOWN. ROD AB IS MADE OF STEEL (E = 210…

A:

Q: A short column has a rectangular cross-section with sides in the ratio 1:2. Determine the minimum…

A: In this question a rectangular cross section is given Load applied is equal to 537 KN Failure stress…

Q: 5. Determine the reactions at A and B for the loaded beams. Beam weight may be neglect 1m 4 m 3m 5 m…

A:

Q: A missile runs freely without of fuel in the location as shown in figure.2, calculate:- 1-…

A:

Q: II. If the beam carries a moving uniform load of FN kN/m and concentrated moving load of SN kN U…

A:

Q: A BRT line operate articulated buses with seating capacity of 200 on 30 km long transit corridor,…

A:

Q: etermine the maximum value of P that can be applied before any slipping takes place. P 80 N μ =…

A:

Q: An outward flow reaction turbine operates under a head of 45 m and discharge of 10 m3/s. The speed…

A: Answer We are given Head H = 45 m Discharge Q = 10 m3/s Speed = 450 rpm speed ratio at inlet = 0.7…

Q: support A 6 m 66 kN 6 m B

A:

Q: Solve for the reactions and draw the shear and moment diagram. Show complete solution.

A: Solve for the reactions and draw the shear and moment diagram.

Q: A reinforced concrete beam is subjected to w=70 kN/m load as shown below. Knowing the modulus of…

A: Using area equivalent method  Modular ratio (m) = Es / Ec  m = 200/25 = 8  Above question is…

Q: A factory discharges waste water to a nearby river. The concentration of dissolved oxygen (DO) a few…

A:

Q: The shorter leg of two 6" x 4" x 1/2 angles are welded to a 12" - 20.7 lb channel. Determine the…

A: This question is related to the Steel Design.

Q: Determine the pressure at the higher end if the pressure at the lower end is 24.525 N/cm^2. 23.924…

A:

Q: AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS…

A: Es = 210GPa  EAl = 65GPa  EB = 80GPa

Q: Determine void ratio n=0.218

A: Introduction : The given question is related with geotechnical engineering . In this question we are…

Q: THE RIGID BEAM IS SUPPORTED BY A PIN AT A AND WIRES BD AND CE. IF THE LOAD P ON THE BEAM CAUSES THE…

A:

Q: Determine the size of a high rate trickling filter for the following data: BOD concentration in the…

A:

Q: Calculate the support reaction forces of the truss as illustrated below and the forces on members…

A:

Q: What are the difference of quantitative and qualitative data in collection procedure?

A: in this question different between quantitative data collection approach and qualitative data…

Q: P Q1: The C-shaped steel bar has cross section of a square of side 1.6 in. If the magnitude of…

A: Find the equivalent moment and axial force acting on the section containing point A. Then using the…

Q: At night, water is pumped from a treatment plant reservoir through distributing piping to an…

A:

Q: The figure below, represents the infiltration characteristics of a catchment developed based on…

A:

Q: The system is released from rest. The 4-kg mass slides on the smooth horizontal surface. By using…

A:

Q: A simply supported W18 x 119 A992 steel beam with 8 meters in length was subjected to a service load…

A: Given : A simply supported W18 x 119 A992 steel beam with 8 meters in length was subjected to a…

Q: 5.41 A nationwide survey of 17,000 college seniors by the University of Michigan revealed that…

A: Given  Total no. Of seniors= 17,000

Q: 4. An aluminum baseball bat, which is 0.8950 m in length when the temperature is 34.7°C, is left…

A: To Determine Bat's new length, L'

Q: show steps At point (A)

A: Given Data:Load=20kNL=4mb=200

Q: ing width of 1.75m .35m. And after the oth of flow is 1.2m. F Discharge per unit v Discharge in the…

A:

Q: Free bely 5. Determine the reactions at A and B for the loaded beams. Beam weight may be neglected.…

A:

Q: Your assigned problem: The channel consists of an unfinished concrete section (n 0.014) and overflow…

A:

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

A:

Q: ● The maximum shearing stress. ● The principal stresses and planes.

A: This question has been taken from solid mechanics

Q: It is observed that the skier leaves the ramp A at an angle 0= 25 with the horizontal. If he strikes…

A:

Q: Answer and show complete solution. Pls don't reject A factory discharges waste water to a nearby…

A: