eequu Fign 1: Figure 1.1 shows a rod, AB, 1 m long, and with weight W, which is held in quilibrium by a vertical wall, the horizontal floor and by a cable CB (see figure 1.1 for details). (a) Assume there is no friction, derive all the external forces acting on the rod. dails). (b) Assume there is friction at the wall and at the floor, with coefficient of static friction, us=0.3, and assume that the rod is under impending motion conditions, derive all the external forces acting on the rod. C 15⁰ 30⁰ Figure 1.1

eequu Fign 1: Figure 1.1 shows a rod, AB, 1 m long, and with weight W, which is held in quilibrium by a vertical wall, the horizontal floor and by a cable CB (see figure 1.1 for details). (a) Assume there is no friction, derive all the external forces acting on the rod. dails). (b) Assume there is friction at the wall and at the floor, with coefficient of static friction, us=0.3, and assume that the rod is under impending motion conditions, derive all the external forces acting on the rod. C 15⁰ 30⁰ Figure 1.1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the wall. A 700N man stand 6m up from the bottom of the ladder. Find the horizontal force necessary at the base to keep the ladder from slipping. Draw a FBD
Q2) The ladder as shown in figure (2) has a long 15 ft and weighs 50 Ib. It rests against a vertical wall and horizontal floor as shown in figure (2), what must the coefficient of friction u be for equilibrium?, then discuss your results. Ladder 50° Figure (2):
In an experiment to find the coefficient of static friction, two plates (e) made of the sam material, m, = 200 gm, and m,= 400 gm. Each plate is put on the top of the same inclined plane, and we start to increase the inclination angle (z Jeo Legb). e Select one: a. The coefficient of static friction determined using m, is lower b. The coefficient of static friction determined using m, is lower will slide at lower angle than m, c. m1 d. Both will slide at the same angle
..A mass of 4kg rests on a horizontal plane. The plane is gradually inclined until at an angle e= 15° with the horizontal, the mass just begins to slide. What is the coefficient of static friction between the block and the surface?
A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the wall. A 700N man stand 6m up from the bottom of the ladder. Find the horizontal force necessary to keep the ladder from slipping.
7. A compound lever as shown below. Find the effort P. if the system is used to lift a mass of 800kg. (10) S00 mam 400 mm 350 mm S0mm 800 kg 8. An oil drum 600mm in diameter and length Im is to be rolled over a step 120mm in height. Find the least pull through the centre of the drum required just to turn the drum over the step. Also find the reaction on the step. Assuming all the surfaces to be smooth. Take density of oil as 1 kg/litre and neglecting weight of the drum. (10) 50 mm
Example 1: A 200 Ib block is at rest on a 30° incline. The coefficient of friction between the block and the incline is 0.20. Compute the value of a horizontal force P that will cause motion to impend up the plane. Given: e = 30° W = 200 pounds (motion) 200# Unknowns: N, P, F 300 30 N
A rope is hung over a stationary drum with weights on each end (100N; 400N). The rope is just on the point of slipping. What is the coefficient of friction, and wrapped number. And also, if we take the same rope and making 14 turns around a stationary horizontal drum to support a heavy weight. If the coefficient of friction is Almost the same, what weight can be supported by exerting a 50-lb force at the other end of the rope?
An engineer trying to determine whether her crane will tip over when attempting to lift a 13K load. Her crane has a 15K chassis and 35K counterweight. Assume all other parts of the crane have negligible weight. Answer all questions relative to the rotation point. How much torque is caused by the load? How much torque is caused by the chassis? How much torque is caused by the counterweight? What is the normal force on the rear (right) outriggers? What is the normal force on the front (left) outriggers? *each box in picture = 5 ft
A sled of mass 500kg sits at rest on a rough slope that is inclined at 10* to the horizontal. The coefficient of friction between the slope and the sled is 0.3. The sled is held in place by a wire attached to a winch. The tension in the wire is TN. a) Find the maximum possible value of T. A load of mass mkg is added to the sled, and tension in the wire is increased to 5000N in order to pull the sled and load up the slop. Given that the sled and load are pulled a distance of 100m in 80seconds, b) Work out the value of m
(c) Figure Q2 shown a 100 N force acts on a 300 N block placed on an inclined plane. The coefficients of friction between the block and plane is u-0.25. Test whether the block is in equilibrium and find the value of the friction force. 12 (1
(2) Force P = 100 lb, is applied to a small pulley that rolls freely (no friction) on cable ACB. If the tension in the cable is 100 lb: a) What is the tension in the cable? 30°