Each of the Mohr's strain circles below represent the state of strain on the blue squares shown in the distortion images. The edges of the squares are aligned with the directions of the principal strains. The red rectangle represents the shape that the square will be when the strain is applied. Match each distortion image to the Mohr's circle which best represents the strain which will generate the distortion shown. 1. 3. 2. 3. 3. 3. 3. 7/2

Each of the Mohr's strain circles below represent the state of strain on the blue squares shown in the distortion images. The edges of the squares are aligned with the directions of the principal strains. The red rectangle represents the shape that the square will be when the strain is applied. Match each distortion image to the Mohr's circle which best represents the strain which will generate the distortion shown. 1. 3. 2. 3. 3. 3. 3. 7/2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The strain components, ex= 940 micro strain, ey= -360 micro strain and yxy=830micro strain are given for a point in body subjected to plane strain. Determine; a. Magnitude of the principal strains b. The direction of the principal strain axes c. The maximum in-plane shear strain. Confirm your answer by means of Mohr's circle of strain and determine the linear strain on an axis inclined at 20 degrees clockwise to the direction of ey
The strain rosette shown in figure was used to obtain strain data at a point on the surface of a machine part. If the readings from gages a, b, c were 650, -450, -585 (all in microns) respectively; which of the following is the shear strain on the surface? 45° a Lutfen birini seçin a1370 micron b. 1570 micron c1400 micron d7600 micron
5. Please calculate the strain and stress in the following two prompts a. A 1 cm long section of tendon stretches to 1.011 cm when it is subjected to a tensile force of 40,000 N. What is the strain in this segment of tendon? @? 17 b. The section of the patellar ligament in the previous question is 0.02 m² in the cross section. What is the stress in this section of ligament as a result of 50,000 N tensile force? E = Δι 19 0 = A 1.011 cm 50000 0,02 Scoco 40000 1.25 = T % 2500000 strain N/m² on trito flox your wrist, you may notice that your
QB3 TWO DIMENTIONAL STRAINThree strain gauges were arranged in the form of a rectangular rosette and positioned on atest surface. The measured strains were as follows: 1 = 200x 10-6 2 = 100 x 10-6 3 = 50 x 10-6Determinea) the principal strains and the principle stressesb) the direction of the greater principal strain relative to gauge 1 and sketch the Mohrstrain circle. Take the Young Modulus of Elasticity value to be E = 200 GN/m2 andPoisson’s ratio  = 0.28.
A bar is compressed to half of its original length. The magnitude of true strain produced in the deformed bar is (correct to two decimal places).
The ratio, when a sample object is stretched, of the contraction or transverse strain (normal to the applied load) to the extension or axial strain (in the direction of the applied load) is referred to as O Answer not in the choices O Transverse-to-axial strain ratio O Puzon's ratio O Poisson's ratio O Dilatation ratio
3.56. Check whether or not the following distribution of the state of strain satisfies the compatibility conditions: where k = 10-4. XX+XX₁X3 0 [E]=k|x² + x3 Kinematics of a Continuum 169 X₁ X1Xx3 X₁ X²
2.25 Closely spaced lines are etched into a silicon wafer, and an optical scanner is used to count the lines. When the wafer is unloaded, the scanner measures 9512 lines within a 1 mm length. While the same wafer is subject to an axial loading acting perpendicular to the lines, the scanner measures 9525 lines within a 1 mm length. Determine the magnitude of the strain and whether it is tensile or compressive. Prob. 2.25
A loading causes the block to deform into the dashed shape. Explain how to determine the strains (gA)xy, (gB)xy. The angles and distances between all lettered points are known.
In a forming process the diameter of the specimen is 1 cm and its length changes from 50 mm to 60 mm. Show the maximum force value on the graph of Force vs. True Strain plotted in Excel Program or any plotting program not by hand using the flow stress equation given below. σ= Kεn and σ=F/A Where the parameters are σ : True Stress in MPa K: Strength Coefficient, K=210 in MPa ε : True Strain, ε=ln (l/l0) n: Strain Hardening Exponent, n=0.27 F: Force in 10 A : Area in mm2 Take at least 3 digits after the decimal point. Specify the units. You can use Excel or any plotting program not by hand then paste your graph into the solution section.
Material A has a modulus of elasticity between Materials B and C, where the value of Material B is the highest and Material D is the lowest. Materials A and B do not undergo plastic deformation with the same strain value. Material B has the same strength as Material C, but higher than Material A. The strength of Material A is the same as that of Material D. Materials C and D experience the same strain with considerable plastic deformation. a. Draw the stress strain curves of the 4 Materials in one axisb. If you are asked to select a material according to the following criteria (state and explain why): i. Highest toughness: ii. Highest stiffness Supreme power iv. Highest tenacity If an application requires a material with low stiffness and high ductility, which material will you choose? NEED IN RUSH THANKS
If the cylinder has the following strain gages readings under internal pressure of 3000 MPa, the Lateral strain reading is obtained from Strain Gauge 1 Strain Gauge 2 Strain Gauge 6 556.1 -188.8 542.7 Select one: a. 1 and 6 b. 6 С. 2 d. 1