Dron Acompound steel [G=80 GPa) shaft consists of a solid 110-mm-diameter segment (1) and a solid 56-mm-diameter segment (2). The allowable shear stress of the steel is 96 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to 54°. Determine the magnitude of the largest torque that may be applied at C. (1) 120 (2) 18 Te

Dron Acompound steel [G=80 GPa) shaft consists of a solid 110-mm-diameter segment (1) and a solid 56-mm-diameter segment (2). The allowable shear stress of the steel is 96 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to 54°. Determine the magnitude of the largest torque that may be applied at C. (1) 120 (2) 18 Te

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T = 10 °C, determine the average normal stress in each member when T2 = 45 °C. Also, how far will the collar be displaced? The cross-sectional area of each member is 1130 mm?. B. -1 m - -0.6 m-
A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of diameter 50 mm. 2GB) Both shafts are firmly (Gs jointed. The combined assembly is subjected to a torque of 1000 Nm. calculate maximum shear stress = developed in steel in N/mm2 (up to 2 decimals)
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 25 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 60 MPa. If a torque of Tc = 8,500 N-m is applied at C, determine the minimum required diameter of the brass shaft (1). (2) B O 89.9 mm O 112.3 mm O 165.4 mm O 138.1 mm O 120.1 mm
Determine the following: a.) the tensile steel ration for positive bending. b.) the depth of the uniform rectangular stress block on the beam section at the ultimate stage when subject to positive bending. c.) the design moment capacity in kN-m of the beam in positive bending.
The rotation is prevented at the lower end of each shaft. The torque of 50 Nm is appliead at end A of shaft AB. The shaft are made os the same A36 steel. r= 40 mm The part ist fix at both ends Determine: Torque of shaft AB Torque of shaft CD c. r = 60 mm а. 15 mm - 12 mm b. Maximum shear stress shaft AB and CD 200 mm A36 steel 304: E= 210 GPa; G=77 GPa; oy=240 MPa; ou=400 MPa B D
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m Sm A B L= 6m 9o kN L-4m A= 0.04 m A = 0.0 6m² E=200 GAa E=80 GPa
The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P if the working stresses are 240 MPa for steel and 120 MPa for aluminum, and the total elongation of the bar is not to exceed 6 mm. 1.5 m 2 m 2P P Steel Aluminum A = 18 mm2 E = 70 GPa A = 12 mm2 E = 200 GPa %3D
The rigid bar abcd supports point loads At A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point B. (In mm)
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E, = 10000 ksi] alloy. The length of segment (1) is L, = 70 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 98 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of 8z = 2100 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 Aluminum B Сорer Answer: in. AL = i
Q1: A torque T = 4 kN.m G of steel core 77 GPa and G of aluminum 27 GPa. Determine: (a) maximum shearing stress in the in the steel core. (b) the maximum shearing stress in the aluminum jacket. (c) the angle of twist at A. 172 mm 54 mm- A Steel core- 25 m Aluminum Q2: aluminum rod AB (G=27GPa) brass rod BD (G= 39GPa). portion CD of the brass rod is hollow and has an inner diameter of 40 mm, Determine: a) the angle of twist at A. b) maximum shear stress of rod AD c) torque diagram d) angle of twist diagram 60 mm TB 1600 Nm 36 mm T₁ = 800 Nm. 400 mm q+ 375 mm 250 mm
Situation 2| The compound shaft as shown is attached to rigid supports. It is subjected to a concentrated torque at the junction. The length of the steel segment is 1m. 3. Determine the ratio of the length of the steel segment to that of the bronze such that the materials will be stressed to their limits. 4. Determine the torsional reaction, in N-m, at the right supports if the applied torque at the junction is maximized. 5. Determine the angle of twist, in ° degrees, at the junction. Bronze = 75 mm G = 35 GPa T= 60 MPa Steel = 50 mm G = 83 GPa = 80 MPa %D Tll IA a b.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L1 = 55 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.35 in., a wall thickness of 0.07 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.3 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.