Drive an expression for heat transfer and temperature distribution for steady state one dimensional heat conduction in a plan wall. The temperature is maintained at a temperature Ti at x=0, while the other face X-L is maintained at temperature T2, the thickness of the wall may be taken as L and the energy equation is given by: d²T/dx² = 0.

Drive an expression for heat transfer and temperature distribution for steady state one dimensional heat conduction in a plan wall. The temperature is maintained at a temperature Ti at x=0, while the other face X-L is maintained at temperature T2, the thickness of the wall may be taken as L and the energy equation is given by: d²T/dx² = 0.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.3P

See similar textbooks

Similar questions

A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where T is in kelvin. If one surface of this wall is maintained at 150C and the other at 50C, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.
A plane wall of thickness 2L has internal heat sources whose strength varies according to qG=qocos(ax) Where qo is the heat generated per unit volume at the center of the wall (x=0) and a is a constant. If both sides of the wall are maintained at a constant temperature of Tw, derive an expression for the total heat loss from the wall per unit surface area.
2.15 Suppose that a pipe carrying a hot fluid with an external temperature of and outer radius is to be insulated with an insulation material of thermal conductivity k and outer radius . Show that if the convection heat transfer coefficient on the outside of the insulation is and the environmental temperature is , the addition of insulation actually increases the rate of heat loss if , and the maximum heat loss occurs when . This radius, is often called the critical radius.
1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
Drive an expression for heat transfer and temperature distribution for steady state one dimensional heat conduction in a plan wall. The temperature is maintained at a temperature Ti at x=0, while the other face X-L is maintained at temperature T2, the thickness of the wall may be taken as L and the energy equation is given by: d²T/dx² = 0. : Sketch a simple diagram for the temperature distribution in plane wall for a steady state one dimensional heat conduction, with heat generation. The surface temperature of the walls Ti and T2, for the cases Ti>T2, T1-T2, and T2>T1. The thickness of the wall may be taken as 2L
1 . A long cylindrical shell outer radius R₂ = 2 cm is shown in cylindrical shell is temperature Ti=10 c° and outer wall at Constant temperature T₂ = 20 C° Calculate the temperature at r= 1.5 cm (Consider conduction only) Assumptions: system is Thermal in Given: The of inner and the figure. The radial + The differential The system is: J²T dr² r maintained at steady state conductivity, K = 22.5 w/mc, system follows Fourier's law of heat Heat loss in axial direction is negligible. JT dr radius Ri=1cm Length L=lom inner Wall Constant is maintained = 0 of is Ti RI R₂ constant. conduction. equation representing Tz
The heat flow per unit length of a thick cylindrical pipe is 772 W per meter. The pipe has radii ri = 12 cm, ro = 24 cm, outside surface temperature, To = 95 deg C and k = 0.05 + 0.0008T where T is in deg C and k is in W/(m K). Find the inside surface temperature of the pipe, assuming steady state conditions and accounting for the variation of thermal conductivity with temperature. Also determine the temperature of a point midway to the inside and outside radius.
Heat flows through the wall in the following figure from the warm inside T, to the cooler The outside T, . In the center of the wall is a glass block of thickness t and thermal resistance R, . 2 thermal resistance of the wood and brick are R ,R, respectively. (a) wall, qw· The remainder of the wall is composed of two layers (wood and brick) each of thickness Find an expression for the steady state heat flow through the wood layer of the Determine the total resistance. (b) brick wood Rb Rw L glass Rg To TA
Inner diameter 30 cm, outer diameter 40 cm and heat conduction coefficient 20 W / m ∙ a cylindrical pipe with oC Take it. 25 W / m3 uniformly on the pipe wall There is a constant rate of heat generation. Tube inner surface temperature 75 oC and outer surface temperature is 95oC. a) Obtain a general correlation for the temperature distribution in the pipe (steady state). b) Calculate the temperature at the midpoint of the pipe wall.
1-D, steady-state conduction with uniform internal energy generation occurs in a plane wall with a thickness of 50 mm and a constant thermal conductivity of 5 W/m/K. The temperature distribution has the form T = a + bx + cx² °C. The surface at x=0 has a temperature of To = 120 °C and experiences convection with a fluid for which T.. surface at x= 50 mm is well insulated (no heat transfer). Find: (a) The volumetric energy generation rate q. (15) (b) Determine the coefficients a, b, and c. 20 °C and h 500 W/m² K. The To: = 120°C T = 20°C h = 500 W/m².K 111 Fluid T(x)- = q, k = 5 W/m.K L = 50 mm
3- A large plane wall has a thickness L=50 cm and thermal conductivity k=25 W/m.K. On the left surface (x=0), it is subjected to a uniform heat flux go, while the surface temperature To is constant. On the right surface, it experiences convection and radiation heat transfer while the surface temperature is TL = 225°C and surrounding temperature is 25°C. The emissivity and the convection heat transfer coefficient on the right surface are 0.7 and 15 W/m²K, respectively. (a) Derive the temperature distribution equation for the wall parametrically (based on x, T₁, qo, L, and k). Plane wall Tsurr = 25°C T% = 25°C k = 25 W/m.K h = 15 W/m²K 90 ε = 0.7 T₁ = 225°C (b) Determine the temperature of the left surface of the wall at x=0? L x