Determine the value of shunt resistance required to convert a galvanometer into ammeter of reading up to 14 A, when the internal resistance of galvenometer is 27 ohms and the value of current for full scale deflection is 0.5 A.

Determine the value of shunt resistance required to convert a galvanometer into ammeter of reading up to 14 A, when the internal resistance of galvenometer is 27 ohms and the value of current for full scale deflection is 0.5 A.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter12: Batteries And Other Sources Of Electricity

Section: Chapter Questions

Problem 14RQ: 14. A 6-V lead-acid battery has an A-hr rating of 180 A-hr. The battery is to be load-tested. What...

See similar textbooks

Related questions

Q: What is a resistor and what it’s used for

Q: what is the mathematical relationship between voltmeter readings?. 2: what happens to the potential…

A: The mathematical relation ship for the circuit diagram voltmeter is V4 = V1 + V2 + V3 this is due…

Q: (a) A 4.7-kΩ resistor is purchased with a tolerance of 1 percent. What is the possible range of…

A: Given: Rating of the resistance = 4.7 kΩ = 4700 Ω Tolerance = 1% Maximum Resistance…

Q: Calculate the value of the shunt resistor, RA, to give a full-scale current reading of 5 A. Answer…

Q: An undetermined number of feet of wire have been used with a diameter of 1/16 inch and the…

A: Given : D =116 inchinch=0.0254 cm-3

Q: Q1\ An ohmmeter has a moving coil of resistance 25 2 with 5mA full scale deflection current. The…

A: Given,For an ohm-meter,Internal resistance, Rin = 25 ΩFull scale deflection current, IF = 5mABattery…

Q: Calculate the actual tolerance value of a resistor that is 97 ohms with a tolerance of +\ - 20%

A: Here value is given and need to find actual tolerance values

Q: 108, Electric Circuits Study Name omework 7, Measuring Instruments Vocabulary. Define each of the…

A: As per company policy i suppose to answer only 1st 3 subpart reat of the part consider as different…

Q: An ammeter with range 0 to 2 mA has internal resistance of 10 N. What is the value of shunt…

Q: A 39-kΩ resistor has a 10 percent tolerance. What is the range of resistor values corresponding to…

Q: A galvanometer has a current sensitivity of 1 (micro A/ mm) and critical damping resistance of 2…

A: Given values are - Current sensitivity=1μAmmCritical damping resistanceR=2kilo ohm

Q: 3. State the sources of errors which are generally traceable in measuring resistance with Wheatstone…

A: In this question we will write about source of error in measuring resistance with Wheatstone…

Q: What is ammeter reading and value of R. Ammeter is ideal(given).

A: From figure all resistors are in parallel so voltage is same. Using ohms law we will find current in…

Q: equivalent resistance

A: In this question we need to find a equivalent resistance of the given circuit.

Q: A galvanometer coil has a resistance of 12 and the metre shows full scale deflection for a current…

A: Given: Meter resistance, Rm=12 Ω. Meter current, Im=3 mA. Voltage across meter, Vm=ImRm=3×10-3×12=36…

Q: a) Find the value of resistor using colour code (Brown-Orange-Gold-Silver). b) Suppose the measured…

A: a) Given, Resistor color code is Brown-Orange-Gold-Silver

Q: aluminum cable has a resistance of 44 at 30C. calculate the resistance of the cable when the sun…

A: In this question we will find resistance at given temperature..

Q: A linear resistance potentiometer is 50 mm long and is uniformly wound with wire having a resistance…

A: We have an potentiometer with, Length (l) = 50 mm Resistance of potentiometer = 10000 Ω and we have…

Q: 1. Resistance Measurement Choose a 10% (or a 5% tolerance if you don't have a 10%) tolerance…

A: Standard resistance available in market in between 20 and 45 Ohm is 20R 22R 27R 33R 36R 39R 43R 47R

Q: What is the maximum number of different resistance values obtained by using three resistors, if all…

A: Given: Three resistors are given. Required: Maximum number of different resistance values obtained…

Q: Draw the schematic, including values, for an Aryton shunt for a meter movement having a full scale…

Q: It is desired to wind a milliameter shunt using a no. 40 enameled copper wire with a resistance of…

A: To calculate the length of wire required to be used as a shunt

Q: Determine the shunt resistance needed to convert a galvanometer to an ammeter with a full scale…

Q: Which statement is most correct about voltage? It is the same as current flow in every circuit…

A: We need to select correct option for given statement.

Q: Given a 50 Ω resistor with a tolerance of 10%, what is the minimum andmaximum voltage across the…

A: The tolerance of the given resistance of 50 Ω is known, the maximum and the minimum values of the…

Q: how much is the increase of resistance in a wire whose initial resistance is 20 ohms at 30 degree C…

A: According to the question we have to find the value of the resistance at 60 degree.

Q: How much voltage will be dropped across a 40-kΩ resistance whose current is 250 μA?

A: Voltage dropped across a resistance can be found out using ohm’s law. Ohm’s law states that voltage…

Q: DC voltmeter has a resistance of 20,000 ohms per volt. What is the resistance of the meter if the…

Q: Questions: • Do these resistors satisfy Ohm's law? Explain your answer. • Is an ammeter connected in…

Q: Based on how voltmeters are connected to a circuit to measure voltage, should ammeters be of high or…

A: We have given on how voltmeter are connected to a circuit to measure voltage should ammeters be of…

Q: A resistance strain gauge with a gauge factor of 2 is fastened to a steel member which subject to a…

A: We have an strain gauge with, Gauge Factor = 2 Strain (∆LL) = 1 * 10-6 Resistance (R) = 130 ohm We…

Q: A voltmeter with a range of 0 to 100 V reads 2 V when the leads are shorted together. The…

A: Given data: A voltmeter with a range of 0 to 100 V. Calculating the uncertainty of the voltmeter,…

Q: What's the accuracy of the 6½ digit DMM if it measured 1.6V (DC) on the 100V range and 10V range…

A: Sensitivity=resolution*range

Q: A wire of resistivity 2.8 x 10^-8 ohm. m and length 20-m must dissipate electrical energy at a rate…

A: An object's resistance is determined by its shape and the material it is made of. The cylindrical…

Q: The ammeter-voltmeter method is used to measure the resistance. With the voltmeter connected across…

A: In the question, Find the true value of the resistance? If reading of ammeter I= 0.8A Reading of…

Q: What is K Map and how to make table through k map and how to grouping. i) Implement half subtractor…

Q: Design a multirange d.c. milliammeter with a basic meter having a resistance 75 ohm and full scale…

Q: steps in solving problems related to resistivity

A: Resistance R is given as- R=lσAσ=conductivity of the materialρ=1σwhere, ρ=resistivity of the…

Q: Questions Ohm's Law experiment 1- What is the aim from Ohm's Law experiment ? 2- What is the used…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: A voltmeter rated 150 volts has an internal resistance of 10 k?. What resistance should be added in…

Q: What are the relationships of resistance, voltage and current, and the distribution of voltages and…

Q: - If the current to an ammeter (A 20) produces a deflection (90), then how will the deflection be…

Q: How do you connect an ammeter to determine the current in a resistor? How do you connect a voltmeter…

Q: A slide-wire potentiometer has a battery of 4 Volt and negligible internal resistance. The…

A: An sliding wire potentiometer is used to provide current to the sliding wire , the current through…

Q: What is the current flow through an ohmmeter when it indicates zero resistance? A. MAXIMUM B.…

A: The explanation is as follows.

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The convention for voltmeters is to use a black wire for the negative reference terminal and a red wire for the positive reference terminal. Explain why two wires are required to measure a voltage. If the wires into the voltmeter are swapped by accident, what will happen during the next measurement?
How does a voltmeter differ from a potentiometer? What type of meter is the Corning-10 pH meter?
What should be the value of Vbb for Ic = 25mA current?
Voltmeter can measure DC current a. O b. only DC voltage Oc only AC voltage both DC and AC voltage d.
Design a multirange d.c. milliammeter with a basic meter having a resistance 75 ohm and full scale deflection for the current of 2 mA. The required ranges are 0-10 mA, 0-50 mA and 0-100 mA ??
A dc voltmeter has a sensitivity of 1000 92/V. When it measures half full scale in 100 V range, the current through the voltmeter is?
QIA 1mA meter movement having an internal resistance of 100 ohm is used to convert into multirange ammeter having the ranges: 0-10mA, 0-20mA, andO-50mA. Determine the value of the shunt resistance required for each range.
An ammeter with range 0 to 2 mA has internal resistance of 10 Q. What is the value of shunt resistance in order to increase the range of ammeter to 100 A?
explain ohms law in terms of resistance
We want to make a resistivity measurement. How should we connect the probes of the multimeter? Drag the connector images to the correct locations and "Not Connected" images to the rest. SLIDE SWITCH: LEFT- OFF MIDDLE- DC VVOLTS DC mA NUMERICAL VALUE OF VOLTS OR MA OR OHMS DISPLAYED HERE 0.00 OHMS FIGHT - AC VOLTS AC mA OFFOO AC DC-n DM 8010 MOVE ROTARY SWITCH TO THIS AREA TO READ OHMS (SELECT RANGE) 1000 200 20 MOVE ROTARY SWITCH TO THIS AREA TO READ VOLTS (SELECT RANGE) 20 200 2K 20K. 200 200K 2M 20M MOVE ROTARY SWITCH TO THIS AREA TO READ mA (SELECT RANGE) *20u 200u 200m 20m 10A mA COM PROBES Windows'u Etkinleştir Windows'u etkinleştirmek için Ayarlar'a gidin NOT CONNECTED
A (0-250) V voltmeter has a guaranteed accuracy of 2 % of full-scale reading. The voltage measured by this voltmeter is 150 volts. The limiting error in percentage for this instrument is?
A galvenometer has full scale current of 20 (mA) and has a meter resistance of 2000 (ohm). To increase the range of galvanometer we add a shunt resistance of 200(ohm). What is value of multiplying factor?