Derive the labor and equipment cost for a 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture based from the following crew team composition, output and given prices.1. Team and Daily Rates1- Project Engineer (P 2000/day)1 - Construction Foreman (P 1000/day)6 - Mason (P800/day)12 - Laborer (P500/day)2. Output of team is 13.5 cu.m per day.3. Equipment (minor tools) is 10% of the labor cost. Determine the total cost of labor and equipment for a 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture based from the followingcrew team composition, output and given prices.281,296.28280,296.28279,296.28288,296.28 Determine the total number of days the team can complete the installation of the 1,000 sq.m 4" thick masonry wall using 1:5 mortarmixture.078

Step 1: Compute the total desired output in cubic meters by multiplying the wall area by its…

Determine the total cost of labor and equipment for a 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture based from the following crew team composition, output and given prices. 281,296.28 280,296.28 279,296.28 288,296.28 Determine the total number of days the team can complete the installation of the 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture. 07 8

Determine the total cost of labor and equipment for a 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture based from the following crew team composition, output and given prices. 281,296.28 280,296.28 279,296.28 288,296.28 Determine the total number of days the team can complete the installation of the 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture. 07 8

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The results of an experiment to evaluate the effects of a water reducer areshown in Table P6.32.a. Calculate the water–cement ratio in each of the three cases.b. Using water reducer, how can we increase the compressive strength ofconcrete without changing workability? Refer to the appropriate case inthe table.c. Using water reducer, how can we improve workability without changingthe compressive strength? Refer to the appropriate case in the table.d. Using water reducer, how can we reduce cost without changingworkability or strength? (Assume that the cost of the small amountof water reducer added is less than the cost of cement.) Refer to theappropriate case in the table.e. Summarize all possible effects of water reducers on concrete.
Four standard mortar cubes were made using nonpotable water available atthe job site, and four others were made using potable water. The cubes weretested for compressive strength after 7 days of curing and produced the failureloads in kilograms shown in Table P6.24.Also, the Vicat test was conducted on the cement paste made with the ques-tionable water and showed that the set time is 0.5hour less than the set timeof paste made with potable water. Based on these results, would you acceptthat water for mixing concrete according to ASTM standards? Explain why.
What is the purpose of adding alcohol in test method C173? . When is it necessary to consolidate concrete by vibration in test method C231? Discuss the process of vibration when placing and consolidating the sample. When rodding a layer of concrete in method C138, is it okay to hit the bottom of the measure? If not, how is it supposed to be done?
A concrete masonry unit has actual gross dimensions of 190 mm X 190 mm X190 mm. The unit is tested in a compression machine with the followingresults:Failure load = 436 kNNet volume of 224516 mm3a. Is the unit categorized as solid or hollow?b. Calculate the gross area compressive strength.c. Calculate the net area compressive strength
Three standard mortar cubes were made using nonpotable water available at the job site, and three others were made using potable water. The cubes were tested for compressive strength after 7 days of curing and produced the failure loads in kN shown in Table P6.22. The Vicat test was conducted on the cement paste made with the questionable water and showed that the set time was 45 minutes more than the set time of paste made with potable water. Based on these results, would you accept that water for mixing concrete according to ASTM standards? Explain why.
Three standard mortar cubes were made using nonpotable water available at the job site, and three others were made using potable water. The cubes were tested for compressive strength after 7 days of curing and produced the failure loads in kN shown in Table P6.22. The Vicat test was conducted on the cement paste made with the questionable water and showed that the set time was 45 minutes more than the set time of paste made with potable water. Based on these results, would you accept that water for mixing concrete according to ASTM standards? Explain why. TABLE P6.22 Nonpotable Water Potable Water 70.3 75.2 73.0 83.2 73.8 77.4
A concrete masonry unit has actual gross dimensions of 190 mm * 190 mm *190 mm. The unit is tested in a compression machine with the followingresults:Failure load = 436 kNNet volume of 224516 mm3a. Is the unit categorized as solid or hollow?b. Calculate the gross area compressive strength.c. Calculate the net area compressive strength.
6% (Q.9) What are the effects of hot weather on fresh concrete?
A concrete masonry unit has actual gross dimensions of 190 mm X 190 mm X190 mm. The unit is tested in a compression machine with the followingresults:Maximum failure load = 370 kNNet volume = 5125 cm3a. Is the unit categorized as solid or hollow? Why?b. Calculate the gross area compressive strength.c. Calculate the net area compressive strength.
You are a trainee at the building site which had 3000 NFP bricks delivered. You then determined the compressive strength of each bricks as per SANS227 testing regulations. Bricks were ordered with a nominal compressive strength of 3,5 MPa and minimum individual value of 3,0 Mpa. The results from the lab are as follows: Compressive strength Sample 2 3,4 3,7 Sample 1 3,4 Sample 3 3,4 3,7 Brick no 1 3,7 3 3,5 3,5 3,5 3,2 3,7 3,2 3,3 4 3,2 5 3,7 4,1 3,6 4,0 7 3,9 3,4 3,9 8 3,1 3,1 3,1 3,3 3,3 3,3 2,9 3,1 3,6 3,4 10 3,9 11 4,1 3,8 12 3,7 3,7 From the above set of results, state whether these bricks would be accepted or rejected for based on their strength. Support your answers.
The standard acceptable 28-day compressive strength of grout for hollow unit masonry in MPa is? O a. 5.5 O b. 20.7 O c. 21.0 O d. 13.5 O e. 7.0 To be classified as hollow, the unit must have what percentage voids? O a. between 25 and 60 O b. 25 O C. none of these O d. 60 O e. >60
a Why is it important that the concrete masonry units meet certain absorp-tion requirements?b. A portion of a normal-weight concrete masonry unit was tested forabsorption and moisture content and produced the following weights:weight of unit as received = 4.3 lbsaturated weight of unit = 4.7 lboven-dry weight of unit = 4.2 lbimmersed weight of unit = 2.1 lbCalculate the absorption in lb/ft3and the moisture content of the unit as apercent of total absorption. Does the absorption meet the ASTM C90 require-ment for absorption?