Determine the number of blocks needed to build the exterior stacked block wall from the footing to the top of the stacked block wall. Make sure to make calculations that will let you measure the below grade and exposed wall sections. (The stacked block unit is 8-inches x 8-inches x 16-inches; the decorative block has been eliminated and replaced with the stacked block used in the remainder of the structure.) Materials (per 100 s.I. face area Concrete Block Brick Materials 8x 16 8x 18 5x 12 2.67 x 4 x 8 No. of Units 112.5 100 240 675 Mortar (Cu. F.) Face shell bedding 2.3 2.2 3.6 7.2 Mortar (Cu. FR.) Face shell and web bedding 3.2 3.0 2.5 7.2

Determine the number of blocks needed to build the exterior stacked block wall from the footing to the top of the stacked block wall. Make sure to make calculations that will let you measure the below grade and exposed wall sections. (The stacked block unit is 8-inches x 8-inches x 16-inches; the decorative block has been eliminated and replaced with the stacked block used in the remainder of the structure.) Materials (per 100 s.I. face area Concrete Block Brick Materials 8x 16 8x 18 5x 12 2.67 x 4 x 8 No. of Units 112.5 100 240 675 Mortar (Cu. F.) Face shell bedding 2.3 2.2 3.6 7.2 Mortar (Cu. FR.) Face shell and web bedding 3.2 3.0 2.5 7.2

Fundamentals Of Construction Estimating

4th Edition

ISBN:9781337399395

Author:Pratt, David J.

Publisher:Pratt, David J.

Chapter5: Measuring Concrete Work

Section: Chapter Questions

Problem 6RQ

See similar textbooks

Similar questions

Q4/Classify the Bricks According to the Shape?
GIVE 10 DISADVANTAGES OF USING HOLLOW BLCOKS.
The total length of exterior walls of a residential building is 650 lf. The 8-foot long 2x4 studs are spaced 16 in. OC or less. The drawing of the building shows there are 20 corners requiring three studs. Studs are installed on single 2x4 bottom sill plates and capped by double 2x4 top plates for the entire length of the walls. Both bottom and top plates are 16-ftlong each. Prepare a list of materials for the wall studs, corner studs, sill plates, and top plates. For each of the materials, show the nominal dimension, number of pieces of each length, the length ofa lumber, and the total linear feet. Estimate the total direct cost and cost per linear foot of wall for furnishing and installing the studs and plates. Assume $0.75/bf for lumber, $30.00/hour carpenters, and $24.00/hr for laborers. Use the average value in Table 12.10 for the labor-hours
Concrete Hollow Block 200mm H x 400mm Lx 150mm thick per piece and Laying 4 layers x 4 meters excluding the doorway, is reinforced with 10mm diameter steel bars at every 3 layers horizontally and 0.60 meters on center spacing for vertical bars. a) What is the total area of the CHB installed or laid? A=? in square meters b) How many blocks are required? N=? pieces Provide Wastage Factor = 3% in pieces of CHB c) How much mortar or grout is required in CHB laying? In cubic meter d) How many bags of cement is needed if Class B 1:3 Mixture is required? WF-3% No. of 40kg bags e) Find the volume required for the fine aggregate if WF sand = 15%, in cubic meters f) How many pieces of 10mm diameter x 6 meters long rebar must be ordered? In pieces g) What will be the total mass of the reinforcing steel bars, in kilogram? In kilograms Metal anchors to be enbedded in mortar DOOR- FRAMES
Concrete Hollow Block 200mm H x 400mm L x 150mm thick per piece and Laying 4 layers x 4 meters excludingthe doorway, is reinforced with 10mm diameter steel bars at every 3 layers horizontally and 0.60 meters oncenter spacing for vertical bars.a) What is the total area of the CHB installed or laid? A=? in square metersb) How many blocks are required? N=? pieces Provide Wastage Factor = 3% in pieces of CHBc) How much mortar or grout is required in CHB laying? In cubic meterd) How many bags of cement is needed if Class B 1:3 Mixture is required? WF=3% No. of 40kg bagse) Find the volume required for the fine aggregate if WF sand = 15%, in cubic metersf) How many pieces of 10mm diameter x 6 meters long rebar must be ordered? In piecesg) What will be the total mass of the reinforcing steel bars, in kilogram? In kilograms
way to Determine the required thickness of the concrete base ?
To be classified as a tile, a unit must have what percentage voids? а. 60 b. >60 c. 25 >90 d. none of these
Concrete technology Detailed answer
Concrete estimate
Submit your question to our 24/7 subject matter experts with Masters and PhDs and get a solution in as fast as 30 minutes* Provide clear and step by step solution Using LRFD, PL400x350 mm base plate, W12x120 column, 500x500 mm pedestal, PDL = 1200 kN and PLL = 800 kN. Use A-50 steel and concrete fc’ = 30 MPa. Determine the required base plate thickness.
Number of modular bricks required for one cubic metre of brick masonary are
yout dy) I References Font 11 Mailings Review View Paragraph 2 AaBbCcDc AaBbCcDc AaBbC AaBbcc AaB AaBbCc. AaBbCcL 1 Normal 1 No Spaci... Heading 1 Heading 2 Title Subtitle Subtle Em Styles Determine the approximate proportion of the dry cement mortar required for brick work with bricks of nominal size] 19*9*9 cm, with 18% extra for frog filling and wastage is. (assume 1 m^3 wet mortar = 1.3 m^3 of dry mortar)