Determine the horizontal displacement of joint B. You can assume that joint B displaces to the left.    The length of the truss AB, BC, AC, L, is 1,760 mm. The applied force at point C, P, is 60 kN. The diameter of the trusses, D, is 16 mm. The elastic modulus of the three trusses , E, is 200 GPa.

Q: A test well is to be constructed for dewatering purpose in a planned excavation for foundation. The…

A: To draw the spring and decide the boundaries, we first need to comprehend the idea of drawdown,…

Q: Let having all the expenditure, Rs 100 be the cost/hr of a shovel with volume 10 m³ which will be…

A:

Q: A drain pipe is to be laid between two points. One point is 13'0" higher in elevation than the other…

A:

Q: 2) The basin area is 138 km² and the limit soil moisture is 111 mm. Using the PET values that you…

A: Catchment area = 138 km2 Moisture limit = 111 mm Month T oC k p PET April 18.82 0.6 0.07 0.0692…

Q: For the conditions in Figure P4.15, select a. W12, A36 steel b. a pipe c. a square structural tube…

A: from LFRD approch,         Pu = 1.2D + 1.6L               = 1.2×90 + 1.6×260             = 524 kips…

Q: A municipal wastewater flow of 1,000 m³/d contains 400 mg/L BOD5 and is treated to be in a trickling…

A: municipal waste water - 1000 m3/d BOD5 - 400 mg/L Specific surface area - 200 m3 / m2  Recirculation…

Q: Draw the moment diagram for the beam and two columns. also make sure to show that the moment are on…

A: ### FOR Bending Moment Diagram for Frame by cutting frame into 3 parts###

Q: A tanker carrying tolueneis unloaded to an onshore storage tank using the ship’s pumps. The pipeline…

A: D = 225 mm or 0.225 m  L = 900 m  ρ = 874 kg/m3 μ = 0.62 cp or 0.00062 Pa-s   NOTE : As per…

Q: Concrete has a coefficient of linear expansion of 12x10-6 /0 C and considering a large concrete…

A: Coefficient of linear expansion of 12x10-6 /0 C, A large concrete structure is considered

Q: A prismatic bar has a cross-section of 25 mm by 50 mm and a length of 2000 mm. Under an axial load…

A: →Cross section Area of prismatic bar A= Breadth×Depth=25×50mm→Length L=2000mm→Axial load…

Q: 1. Design a one-way slab having a simple span of 3.5 m. The slab is to carry a uniform live load of…

A:

Q: Draw the V and M diagram of the beam. The cross section of the beam is a triangle with base 18 and…

A:

Q: low permeability. The water table is 6m below the surface of the sand. For the give unit weight of…

A:

Q: When the compactive effort is increased in a compaction test, the optimum moisture content: (a)…

A:

Q: Problem 11 For a normally consolidated soils, a consolidated-undrained triaxial test was conducted…

A:

Q: Compute full-station elevations for an unequal-tangent vertical curve to fit the requirements below.…

A: Grade, g1=+2.25% Grade, g2=+3.75% Station at VPI, 62+00 Elevation at VPI, EVPI=838 ft L1=700 ft,…

Q: The results of a consolidation test on an undisturbed soil, sampled at a depth of 10 m below the…

A: Consolidation test on an undisturbed soil- Saturated unit weight- γsat=16 KkN/m3, Pre-consolidation…

Q: Hydrological Cycle Determine the optimum number of rain gauge stations in the catchment for an…

A: Admissible error e=10% 4 rain gauge stations Coefficient of variation Cv=30%   It is needed to find…

Q: For the beam shown below, given that L = 7 m, and w=6 kN/m, draw the FBD, shear & momment diagram,…

A: Length of beam(L)=7m w=6kN/m

Q: One side of a traverse has a length of 50 metres and a whole circle bearing of 200°. Calculate the…

A:

Q: A metal bar of 10 mm diameter when subjected to a pull of 23.5 kN gave an elongation of 0.3 mm on a…

A: Diameter d=10 mm Force F=23.5 kN Elongation=0.3 mm Gauge length l=200 mm It is needed to find the…

Q: Note: Use sketch wherever necessary! (Q1) Compute the coordinate of point P in the below figure, if…

A: An open traverse ABCP is given. The azimuth of AB is αAB= 240°10'05'' The horizontal distance line…

Q: Undrained triaxial tests are to be carried out on soil samples which have property as c = 0.28…

A:

Q: A line measures on the ground 137.28m. Using a ruler, the length of this line is 13.55cm on the map.…

A: Length of the line on the ground (L) = 137.28 m  Length of the line on the map (l) = 13.55 cm…

Q: If a fluid jet discharging from a 50 mm diameter orifice has a 40 mm diameter at its vena-contracta…

A: Orifice diameter D=50 mm, Diameter at vena-contracta d=40 mm   It is needed to find the coefficient…

Q: Q.4) A wet soil sample having a volume of 75 cm³ is brought to the laboratory. When this soil sample…

A:

Q: We know that P=Q=480 N, calculate (a) the distance a for which the absolute value of the bending…

A: P= 480 N Q = 480 N

Q: The area of the cross section of an airplane wing has the following properties about the and y axes…

A: Ix=450 in4Iy=1730 in4Ixy=138 in4To determine- Mohr circle

Q: The data for an agricultural field for a specific month are given below: Pan Evaporation = 100 mm…

A: Crop Coefficient = 0.4 Irrigation Efficiency = 0.5 Pan Evaporation = 100 mm Effective Rainfall = 20…

Q: A coarse-grained soil has a voids ratio 0.75 and specific gravity as 2.75. The critical gradient at…

A: A coarse-grained soil- Void ratio e = 0.75 Specific gravity G =2.75 To Find- The value of the…

Q: With velocity of 7 m/s in the 330 mm diameter pipe in the figure shown, determine the discharge in…

A:

Q: Draw a moment diagram and determine the largest moment at support and field in the statically…

A: A statically indeterminate beam is given which is loaded with UDL of q kN/m throughout the beam. The…

Q: A flownet below a dam consists of 24 equipotential drops and 7 flow channels. The difference between…

A: Equipotential drops ,Nd  =24, no.of flow channels, Nf = 7, Specific gravity, G =2.70, Void ratio, e…

Q: WW 4m B 3m C 28 KN/m 6m D 4m

A:

Q: for a sand sample the values of the m mum (emin) and maximum void ratio (emax) are 0.42 and 0.67,…

A: emin=0.42emax=0.67Dr=87%To find:-a) Corresponding range in dry unit weightsb) Corresponding range in…

Q: shear force and bending moment

A: Draw shear force and bending moment diagram.

Q: Question In fully developed laminar flow in a circular pipe, if the velocity at midway between the…

A: A fully developed laminar flow in a circular pipe- Velocity at midway between wall surface and…

Q: A new water supply main is being planned for a new city of 2 million population and average per…

A:

Q: A double-angle tension member is attached to a 7/8-inch gusset plate, which in turn is connected to…

A: The thickness of the gusset plate = 7/8 in The service load consist of 25% dead load The service…

Q: Remote sensing is used to obtain information about objects, areas phenomenon by collecting data…

A: This question is related to the Surveying Engineering from Civil Engineering.  In this question ask…

Q: a column which must support a compressive axial load of 10,000 pounds. Assume that the load is…

A:

Q: For a homogeneous earth dam 52 m high and 2 m free board, a flow net was constructed and number of…

A: A homogeneous earth dam- Height = 52 m and 2m freeboard, Head H=52-2m,H=50 m.Coefficient of…

Q: Determine the head causing the flow of a flat topped and broad - crested weir of 10.3m length has a…

A: Length of broad crested weir = 10.3 mHead = 50 cm=0.5mCd=0.62

Q: A steel wire (E= 200 GPa) of diameter d= 1.25 mm is bent around a pulley of radius Ro= 500 mm. What…

A:

Q: A right circular cylindrical tank container, 2m in diameter and 4m high is 1/2 full of water. When…

A:

Q: 7) 115kN + a) Compute the reaction at A. b) Reaction at B Moment at A. c) 3m- Ism AL

A:

Q: 1) Rainfall data of 4 stations in the same region are given in Table. a) Estimate the missing data…

A: By weighted arithmetic mean as no weightage is given assign same weight for all three station now…

Q: Given the column shown and considering bending about the strong axis, calculate the following. Use…

A:

Q: Determine the weight of the gate per eter of (in/out plane of paper) so that it is about to open up…

A: The below figure is shown;

Q: A reinforced concrete pile weighing 30 kN is driven by a drop hammer weighing 40 kN and having an…

A: Ultimate bearing capacity : The maximum gross pressure strength at the foundation's base at which…

Frames

The trusses and frames are the two most important structural members of civil engineering. Trusses are the interconnection of links and other structural members. The interconnection with other members makes the system behave as a single member that supports and transfers loads. Trusses are generally two types, plane truss, and space truss. Frames on the other hand form the skeleton of any building construction. Frames are structures formed by the connection of beams, columns, slabs, and joists. These members provide the building with the required structural support.