Determine (a) the magnitude and (b) direction of the anchoring force needed to hold the horizontal elbow and nozzle combination shown in the figure below in place. Atmospheric pressure is 94.8 kPa. The gage pressure at section (1) is 104 kPa. At section (2), the water exits to the atmosphere. Assume p₁ = 104 kPa, V₁ = 2 m/s. V₂ 160 mm Section (2) 300 mm Water

Determine (a) the magnitude and (b) direction of the anchoring force needed to hold the horizontal elbow and nozzle combination shown in the figure below in place. Atmospheric pressure is 94.8 kPa. The gage pressure at section (1) is 104 kPa. At section (2), the water exits to the atmosphere. Assume p₁ = 104 kPa, V₁ = 2 m/s. V₂ 160 mm Section (2) 300 mm Water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the horizontal and vertical forces to hold stationary the nozzle shown in the figure below. The fluid flowing through it is 10 °C liquid water; A₁ = 1.2 m², A₂ = 0.300 m², V₁ = 15 m/s, p2 = Patm and p₁ = Patm + 75 kPa. Neglect effects of gravity. Fx= i Fy= i A1 P1 KN kN Fy ZA A2, P2 = Patm Fx 45° Patm
A piston moves with constant velocity U0 in a cylinder having radius R. A liquid having density leaves the open end with conical velocity proÖle V~ = V0(1-r/R)^k.Figure for problem 1.(a) If the exhaust port is closed, find the value of V0 in terms of U0. Be sure to define an appropriate control volume for solving this problem.(b) If V0 = U0, find the volume áow rate leaving through the exhaust port (in terms of U0 and R)
Pump BC shown brings oil (SG = 0.72) to reservoir D at 170 L/sec. The energy lost from A to B is 1.1 J/N and from C to D is 4.7 J/N. How many hp is needed for the pump to function if its efficiency is just 80%?
Water in a vertical (i.e., gravitational force of the fluid in the nozzle plays a role, and the elevation change in the Bernoulli's Equation, if needed, should be considered) pipe is charging from an attached bend nozzle into the atmosphere as shown in Fig. 5. The nozzle's weight is 20 kg. The pipe and the nozzle are connected by a flange. The gage pressure of the flow at the flange is 35 kPa when the discharge rate is 0.1 m³/s. The volume of the bending nozzle is 0.012 m³. Calculate the vertical component of the anchoring forcing required to hold the nozzle in place and determine its direction. G= 9.81 m/s². The density of water is 1000 kg/m³. ChatGPT solution: Nozzle 1 Area -0.01 m² P-35 kPa Area -0.025 m² 0.10 ms Figure 5: Q5 35 degree
H.W.2/: The bottom quarter of a vertical cylindrical tank of total height 0.4 m and diameter 0.3 m is filled with a liquid (SG > 1, like glycerin) and the rest with water, as shown in the figure below. The tank is now rotated about its vertical axis at a constant angular speed of v. Determine (a) the value of the angular speed when the point P on the axis at the liquid-liquid interface touches the bottom of the tank and (b) the amount of water that would be spilled out at this angular speed? 3h h = 0.1 m D = 0.3 m
The density of the liquid striking the "splitter" of Figure 6.15 is 830 Kg/m. Dėtermine the force components of the force on the splittèr. Assume a smooth entry / sliding of the stream of liquid. (10) 2 số° Fy 2 Fx cs 30 Q,-0.03 cms Vo = 10 m/s cs 45° Qo= 0.10 cms FIGURE 6.15
Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 12 in. The atmospheric pressure is 14.7 Ibf/in?, the specific volume of water is 0.01604 ft/lb, and the acceleration of gravity is g = 32.0 ft/s?. Patm = 14.7 Ibr/in.? g = 32.0 ft/s² Water v = 0.01604 ft/lb Determine the difference in pressure between points a and b, in Ibf/in2?. Does the pressure increase or decrease from point a to point b? Sten 1
Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 12 in. The atmospheric pressure is 14.7 Ibf/in?, the specific volume of water is 0.01604 ft3/lb, and the acceleration of gravity is g = 32.0 ft/s?. Patm = 14.7 Ibf/in.? g = 32.0 ft/s² Water v = 0.01604 ft³/lb Determine the difference in pressure between points a and b, in Ibf/in?. Does the pressure increase or decrease from point a to point b?
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.3.1 Find the maximum allowable speed to operate the pump3.2 What power is expected in overcoming friction at this speed, take ƒ = 0.01
2. Oil (sg=0.90) is flowing at 150 L/min through a turbine. The pressure before the turbine is 750 kPa and after the turbine 150 kPa with an elevation between these two points of 2.3 m [ fluid entrance is on the high side ]. If the friction loss in the system is 5.10 N.m/N find (a) the power delivered to the turbine by the fluid and (b) If the mechanical efficiency of the turbine is 80 % find the power output from the turbine.
A pressurized tank of water is used to create a fountain, as illustrated. Assume that the water's free surface area in the tank is very large relative to the pipe's cross-sectional area, which is circu- lar with diameter d 1.0 cm. The small pipe bend has height = 10.0 cm. At the instant when 0.75 m, H = 2.5 m, and the gauge measures a pressure of Pgauge 20.0 kPa, the water spray reaches a height L above the pipe exit. h = = = Neglecting viscous effects, determine the height of the spray, L.
3. A 0.8-lbm object travelling at 200 ft/sec enters a viscous liquid and is essentially brought to rest before it strikes the bottom. What is the increase in internal energy, taking the object and the liquid as the system? Neglect the potential energy change. Derive with the formula below, show the cancellation, explain the step by step and draw a free body diagram/figure. refer with this: PE1 + KE1 + U1 + WF1 + Q1 + W1 = PE2 + KE2 + U2 + WF2 + Q2 + W2 + E losses.