Design an Amstrong wideband FM(WBFM) generator for the given criteria below. The carrier frequency of wideband FM (WBFM) fe = 90 MHz and the frequency deviation Af = 65.536 klHz. The carrier frequency of narrowband FM (NBFM) generator f. = [hi] kitz and frequency deviation Af = 0.5 itz. The frequency of the local oscillator is between I MHz-2 MHz. In the frequency multipliers only frequency doublers will be used.

Design an Amstrong wideband FM(WBFM) generator for the given criteria below. The carrier frequency of wideband FM (WBFM) fe = 90 MHz and the frequency deviation Af = 65.536 klHz. The carrier frequency of narrowband FM (NBFM) generator f. = [hi] kitz and frequency deviation Af = 0.5 itz. The frequency of the local oscillator is between I MHz-2 MHz. In the frequency multipliers only frequency doublers will be used.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

12- A DVM measure... a- peak value. b- RMS value. Average value. d- peak to peak value. 13 The study of energy distribution across the frequency spectrum of a given electrical signal is done by a Distortion meter b-wave analyzer.
What is Frequency Modulation? Draw the waveforms.
The carrier frequency is 600 Hz, and the modulating signal is a single-tone sinusoidal signal. The x-axis is in time while the y- axis is the amplitude of the AM signal. If the peak voltage level of modulating and 1v and signal respectively, determine the modulating index. the carrier are 2V 2 1.5 1 0.5 -0.5 -1 -1.5 -2 0.005 0.01 0.015 0.02 0.025 0.03 0.035 0.04 0.045 0.05 Time (s)
One input to a conventional AM modulator is a 600 kHz carrier with amplitude of 22 V. The second input is a 20 kHz modulating signal that is of sufficient amplitude to cause a change in the output wave of +9 V. Determine: a. Upper and lower side frequencies. b. Percent modulation. c. Peak amplitude of the modulated carrier and the upper and lower side frequency voltages. d. Maximum and minimum amplitudes of the envelope. e. Expression for the modulated wave. Then, f. Draw the output spectrum. g. Sketch the output envelope.
How to calculate the efficiency in frequency modulation and what is the highest value for efficiency in frequency modulation
Find the resonance point and the half-width of the speed versus frequency curve for the damped harmonic oscillator, under the action of a sinusoidal driving force. *It is all the data
Obtaining broadband FM signal from narrowband frequency modulated (FM) signal is shown below. The narrowband FM signal has a maximum frequency deviation of 100 Hz. The frequency of the local oscillator is f0=100 kHz. Obtaining broadband FM signal from narrowband frequency modulated (FM) signal is shown below. The narrowband FM signal has a maximum frequency deviation of 100 Hz. The frequency of the local oscillator is f0=100 kHz.Since the broadband FM signal has a carrier frequency of fc=80 MHz, find the N value.
a carrier frequency 10⁶ and amplitude 3V frequency modulated by a sinusoidal wave of frequency is 500 HZ and the peak amplitude 1 Volt as a consequence , the frequency deviation is 1 KHz. The level of the modulating waveform is changed to 5 Volt peak and the modulating frequency is changed to 2KHz. Write an expression for the new modulated waveform.
2. Write an OCTAVE program to plot the signal given below. P- Pmax Sin(21Ift); where Pmax= 10 MW, -60 Hz. %3D Find out time period and verify it with graph. Assume necessary data.
How the phase modulation can generate frequency modulation?
Draw a block diagram of a PM demodulator using frequency discriminator method.
What is the graph of the FM and PM magnitude spectrum with sine modulation?