مرهوالها -ما هي قوة الانماء الاسيه واله وما هو اوما عم لين ان كيث في العلم ومنا للعودbe anzed the design according15 عا فوفوA 2.5 m span cantilever beam has a rectangular section and reinforcement as shownin Fig. 3.15. The beam carries a dead load, including its own weight, of 22 KN/m anda live load of 13.5 KN/m. Using, As-3022, fe = 21 MPa and fy-400 MPa, check ifthe beam is safe to carry the above loads.65 mm400mm3472code?---200 mm -2.0 mME =Cه

Answered: Image /qna-images/answer/28e759f3-ddb8-486d-933d-1a1b44fec3fd.jpg

design 15 یا فردو اهام لين ان كيث في العلم ومنا للعود rang to A 2.5 m span cantilever beam has a rectangula in Fig. 3.15. The beam carries a dead load, inc a live load of 13.5 KN/m. Using, As-3022, f the beam is safe to carry the above loads. 65 mm 400mm 34 22 -200 mm

design 15 یا فردو اهام لين ان كيث في العلم ومنا للعود rang to A 2.5 m span cantilever beam has a rectangula in Fig. 3.15. The beam carries a dead load, inc a live load of 13.5 KN/m. Using, As-3022, f the beam is safe to carry the above loads. 65 mm 400mm 34 22 -200 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum monent 04 the beam could cary of 3ismm fc' = 28mPa fc": fy = 375 m pa 45omm 8-28mmø Minimum concrete cover =4rmm 28mm
Design a simply supported rectangular reinforced concrete beam. Note: Neglected the self-weight of the beam. Wu (D.L) PLL Wa (L.L) h b W D.L P LL W LL Fc bar No. of Fy MPа MPa (mm) (mm) (m) kN/m kN kN/m dia. layers 325 500 17 50 20 20 two 28 420
تيليجرام Water resources/second... منذ لحظات الموسوي ، ل یا سوال WATER RESOURCES/ le sI تعليم كمقروءة SECOND PHASE 10 نقاط find the shear stress in bolt in pin A 60 kN 4M. BOLT DIA 20 м. A 50 kN PIN A 636 MPa O 159 MPa O 318 MPa 79 MPa bläi 6 What is the Shear Force at ?support A 3 kN/m B
1. (a) Calculate the tributary area, AT, for column 2A in the 4th floor (i.e. the column supporting the roof) to be used in calculation of total roof live load on column 1A (note that "roof live load" is different than "floor live load"). (b) Calculate the tributary area, AT, for column 1A in the 2nd floor to be used for calculation of floor live load acting on the column. c) Calculate the tributary area, AT, for column 1B in the 1st floor to be used for calculation of floor live load acting on the column. (d) Calculate the influence area, AI, for column 1B in the 1st floor for floor live load. e) For a specified live load of p. = 40 psf, calculate the design floor live load, pz [psf], for column IB in the Ist floor using floor live load reduction from code (if allowed). () Using your answers from (c) through (e), calculate the axial force, P. [kip], acting at the top of column 1B in the Ist floor due to floor live load. (g) If columns are 16 in. x 16 in. in x-sect, typical floor beams…
Ah G Av E 60° 490 30 Bh B x F x D •METHOD OF JOINTS 20 N Tabulation of forces from Method of Joints: FORCE ACTING |МЕMBERS (N) NATURE DC EC DF GD
concrete : C20 steel: S420 h=550 mm b=350mm steel rebars : 5Φ18
Time: 75 minutes Group -B Design a simply supported rectangular reinforced concrete beam. Note: The self-weight of the beam is not included. Wu (L.L) Wu (D.L) h b L b h L Fc WuD.L Wu LL bar No. of Fy MPa MPa Name (mm) (mm) (m) kN/m kN/m dia. layers 300 500 6.3 17 8.5 20 Two 28 420
A built up section consists of S 150 x 26 and two channels C 380 x 74 having an I effective length of 6 m. The section is pin-connected at both ends. Use A 572 Grade 50 steel and NSCP Specifications. Сотриче Compute OLUTION: Inertia Are a CIVIL ENGINEERING-STEEL DESIGN ; DOUBLE CHECK YOUR ANSWERS Properties of One channel C 380 x 74 A=9480 mm² d = 381 mm I=168 x 106 mm Tx = 133 mm Slenderness ratio: ly=4.6 x 106 mm x = 20.3 mm A=9480+3250 A = 12730 mm² of 7 = A = 3250 mm² 1₂= 10.8 x 10 mm Ly=0.952 x 106 mm X and y. -√√A 1₂=168 x 106 (2) +0.952 x 106 L=336.952 x 106 mm 123.54 x 106 12730 Y = 98.51 Properties of One S 150 x 26 Ty=22 mm t=18.2 mm 1,= 10.8 x 10+ [4.6 x 106 +9480(73.9)2] 2 18.2 1,= 123.54 x 106 d = 152 mm Tx=57.7 mm Ty = 17.1 mm C380x74 20.3 -73.9-73.9- (s 150x26 -152- 20.3 18.2
answer 2.8-9 with fbd please
The asymmetric roof truss is of the type used when a near normal angle of incidence of sunlight ontothe south-facing surface ABC is desirable for solar energy purposes. The five vertical loads represent theeffect of the weights of the truss and supported roofing materials. The 400-N load represents the effectof wind pressure. Determine the equivalent force–couple system at A. Also, compute the x-intercept ofthe line of action of the system resultant treated as a single force R.
30 kN 15 kN/m 8 kN 10 kNm 25 kNm Im Im 3m 1m lm draw internal loading diagram.
0000 5 kN B M Identify the ZERO Force members for the truss FG GH KL L D AB BC CD DE ODF НІ OHI ☐UJ JK OLM K J D D BM BL CL ODL E G JF JG JH DK →5 kN 000 { D MA KF EF