D. A DD mm radius Steel is subjected to tensile test. Determine its yield and ultimate load it can carry in kN when the steel grade is 60 and 40. Determine also its elongation using the stresses if the modulus of elasticity of steel is 2DD GPa. Determine also the weight if the length is DD m and MM m

D. A DD mm radius Steel is subjected to tensile test. Determine its yield and ultimate load it can carry in kN when the steel grade is 60 and 40. Determine also its elongation using the stresses if the modulus of elasticity of steel is 2DD GPa. Determine also the weight if the length is DD m and MM m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A 31 mm radius Steel is subjected to tensile test. Determine its yield and ultimate load it can carry in KN when the steel grade is 60 and 40. Determine also it's elongation using the stresses if the modulus of elasticity of steel is 231 GPa. Determine also the weight if the length is 31 m and 03 m. Need it asap.
A 31 mm radius Steel is subjected to tensile test. Determine its yield and ultimate load it can carry in KN when the steel grade is 60 and 40. Determine also it's elongation using the stresses if the modulus of elasticity of steel is 231 GPa. Determine also the weight if the length is 31 m and 03 m.
A 8 mm radius Steel is subjected to tensile test. Determine its yield and and ultimate load it can carry in kN when the steel grade is 60 and 40. Determine also its elongation using the stresses if the modulus of elasticity of steel 218 GPa. Determine also the weight if the length is 8 m and 18 m.Hint: There are two 8 mm radius Steel.
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
Situation No. 2 A bronze bar is fastened between a steel bar and an aluminum bar as shown below. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Bronze Steel A = 480 mm? Aluminum A = 650 mm A = 320 mm 3P 4P 2P 1.0 m 2.0 m 1.5 m
Problem 2: A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel Bronze 480 mm² 650 mm² 3P 1.0 m 4P 2.0 m Aluminum 320 mm² 1.5 m 2P
A tension stress of 70 ksi was applied on a 12-in. long steel specimen. Determine the resultant elongation assuming that the deformation is entirely elastic. Assume a Young’s modulus of 30 * 106 psi.
5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure 5. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m FIGURE 5 Aluminum A = 320 mm² 1.5 m 2P
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
A steel bar with diameter d1 = 10 mm has upset ends with diameter d2 = 15 mm. The lengths of the bar segments are L1=0.3 m and L2=0.15 m. The radius at the transition R = 1.25 mm and the modulus of elasticity is 90 GPa, the bar product of the load p elongates 0.12 mm normal stress and maximum stress
A specimen of steel 20 mm diameter with a gauge length of 200 mm is tested to destruction. It has an extension of 0.25 mm under a load of 80 kN and the load at elastic limit is 102 kN. The maximum load is 130 kN. The total extension at fracture is 56 mm and diameter at neck is 15 mm. Find . The stress at elastic limit. • Young's modulus. . Percentage elongation. Percentage reduction in area. Ultimate tensile stress. .
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²