D 2 ft -2 ft

Q: Determine the shape factor for the member having the tubular cross section.

A:

Q: v0-52. Locate the centroid y of the cross-sectional area of the concrete beam. 12 in, 12 in. 3 m.:…

A:

Q: The rod BD is made of material with G1= 33 GPa has a diameter 46 mm is bonded to the tube CA at…

A: Given: Rod diameter is 46 mm.  G1= 33 GPa. Tube outer diameter is 97 mm and thickness is 8 mm.…

Q: Two basic methods for calculating deflections of bending members are the formula method and the…

A:

Q: Determine the vertical displacement of point C. EI is constant. Use the method of virtual work.…

A: Deflection at point C is determined by virtual work as given

Q: Determine the second moments with respect to x- (hori- zontal) and y- (vertical) axes through the…

A: Given data: Thickness of flange, tf = 1 in. Length of the flange, lf = 10 in. Length of the web, lw…

Q: l-length steel with a diameter at the wide end twice the diameter at the narrow end determine the x…

A: Given data, Diameter at narrow end = D Diameter at bigger end = 2D To determine, the center of mass…

Q: The curved rod AD of radius r has a weight per length of w. If it lies in the horizontal plane,…

A: Given Data: The weight per length of the rod is: w The length OC is: OC=0.9745r

Q: Determine the shape factor for the wide-lange beam.

A: The shape factor is dimensionless and depends upon the shape and is used to enhance the efficiency…

Q: INA 4.1 (A). Determine the second moments of area about the axes XX for the sections shown in Fig.…

A: Now for determine the second moment of area by using the parallel axis theorem Ix-x=INA+Ar2 Now…

Q: The relay switch consists of a thin metal strip or armature AB that is made of red brass C83400 and…

A: Given data: Armature length, L = 100 mm Moment of inertia, I = 0.18 x 10-12 m4 = 0.18 mm4   Let,…

Q: The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at…

A: Write the given data with suitable variables. dBD=34 mmdo=73 mmt=10 mmT1=579 NmT2=1042 Nm

Q: Determine the vertical reaction at A in kN for the beam shown below, where L7m L22 m 0 20 degrees…

A:

Q: The cross-sectional area of a wide-flange l-beam has the dimensions shown. Obtain a close…

A:

Q: Find the maximum moment of the beam loaded as shown. Express your final answer in N.m to the nearest…

A:

Q: N C 1 in. A -1 in. M-200 kip.in 13 in 8 in in. 8 in 1 in.

A: given: M=200 kip.in Solution: The neutral axis is given as :…

Q: Determine the vertical reaction at Ain kN for the beam shown below, where: L1=3 m L2=2 m Lg-2 m 91-2…

A:

Q: Cantilever beam has fixed support at the point A as shown in Fig. 4. Determine the component of the…

A: Drawing the free body diagram

Q: explain how to find the resultant internal loading acting on the cross section at point A. Draw all…

A: The free body diagram is shown below, Taking moment about point B, ∑MB=0RC×a-Psinθ×2a=0RC=2Psinθ…

Q: Determine the moment ofinertia of the T-section with respect to itscentroidal xo axis. T 100 mm 400…

A:

Q: The framework consists of one cantilevered beam CB and a simply supported beam AB. If each beam is…

A: To find: The deflection at point D at the centre of beam AB. Given: The moment of inertia of beam…

Q: *R8-4. The wires each have a diameter of 12 mm, length of 0.6 m, and are made from 304 stainless…

A:

Q: 10-136* For the shaded composite area shown in Fig. P10- 136, determine The mixed second moment Iy…

A: Given: To find the mixed section moment Ixy for the above section

Q: thin-walled tube is subjected to torsion as shown. Determine the Area bounded by the median lin =30

A: Givenr=300mmθ=80°L=6m

Q: Determine the member end moments at b, Mba and Mbc, in the following structure. EI constant 300kN 2m…

A: Given dataP=300kNRoller support at C which exhibit only vertial force

Q: Determine the bending moment of point D. The supports at A and B are journal bearings. Supply the…

A:

Q: The beam is subjected to the distributed load and the couple shown. If Mis slowly increased starting…

A: Answer: Mo = 5030.67 lb•ft.

Q: uss consists of three members, each made from A-36 steel and having a cross-sectional area of 0.75…

A: given three member truss each member made of A-36 steel length of each member L=16ft=192inand having…

Q: Cantilever beam has fixed support at the point A as shown in Fig. 4. Determine the component of the…

A:

Q: Determine the net area of the given section below. Diameter of bolts is 7/8-in and the thickness of…

A: A screw is a sort of latch, generally produced using metal, that usually includes ahead toward one…

Q: 3) Locate the centroid y of the concrete beam having the tapered cross section as shown. (Ans:…

A:

Q: The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at…

A:

Q: The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close…

A:

Q: The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close…

A: Given: The approximated value of moment of inertia about x-axis, Ix = 654 in^4

Q: Total upward force of 100 lbs is applied. Determine the forces at D and F on the ADF tong. Where is…

A: Total upward force is 100 Lbs. Since, the tong is symmetric about the vertical axis, the total load…

Q: Questions 21, and 22 For the figure shown answer the following: 21. The location of x-coordinate (X)…

A: X = 1.79 m Y = 1.30 m

Q: 15.Form the Fig (2) The second moment of area I, is then given by: 50mm Imm 120mm 2mm Fig. (2) 2mm…

A: Given Data: Width of the top flange, w=50 mm

Q: The beam is made of Douglas fir having an allowable bending stress of sallow = 1.1 ksi and an…

A: The free body diagram of the beam is as follows: Calculate the forces in the vertical direction as…

Q: The L-shaped frame is made from two fixed-connected segments. Determine the horizontal displacement…

A: From the given description:

Q: Find the maximum moment of the beam loaded as shown. Express your final answer in Ib.ft to the…

A: Draw the shear force and the bending moment diagram for the following beam

Q: Determine the vertical displacement of the cantilever beam at point C. 3EI El C

A: At AC length there is no load condition: Load is only acting at the point B of the beam. There exist…

Q: Determine the maximum deflection of the solid circular shaft. The shaft is made of steel having E =…

A: Given data as per the question Diameter of shaft =100 mm Value of E =200 Gpa

Q: 75 kN rod in shape A AAB= 600 mm² ve ABc=AcD= 1200 mm2'lik 20 kN 20 kN It is made of two stages.…

A:

Q: 120 mm 3) Determine the location y for the beam having the tapered cross-sectional area shown…

A: ȳ = 135 mm

Q: Determine the vertical displacement of joint C. Assume the supports at A and E are pins and joint C…

A: Given data as per the question The load applied at point C =8 K Calculating vertical reactions at A…

Q: Using any Geometric Methods only: (Double Integration, Conjugate Beam, Area Moment) Determine the…

A: Answer is given below

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.