Create a bucket by rotating around the y axis the curve y = 2ln(z - 6) from y-0 to y = 8. If this bucket contains a liquid with density 840 kg/m³ filled to a height of 7 meters, find the work required to pump the liquid out of this bucket (over the top edge). Use 9.8 m/s2 for gravity. Work - Joules

Create a bucket by rotating around the y axis the curve y = 2ln(z - 6) from y-0 to y = 8. If this bucket contains a liquid with density 840 kg/m³ filled to a height of 7 meters, find the work required to pump the liquid out of this bucket (over the top edge). Use 9.8 m/s2 for gravity. Work - Joules

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A conical container of radius 5 ft and height 20 ft isfiled to a height of 17 ft with a liquid weighing 51.8 lb/A2 . How much work will take to pump the liquid to a level of 3 ft above the cone's rim?
Steel ball with radius of 0.09 m lays on a bottom of the lake 5 m deep. What work is needed to lift the ball to the surface of the lake? Density of steel is 7860kg/m3. The volume of a sphere is Use g = 9.8 m/s2 Calculate answer to two decimals.
For a given cylindrical tank, the radius is 2 m and the height is 12 m. The tank is filled to a depth of 5 m. How much work is required to pump all of the water over the top edge of the tank? Acceleration due to gravity is 9.8 m/sec² and the density of water is 1000 kg/m³. Round your answer to the nearest kilojoule. Sorry, that's incorrect. Try again? W = kJ
A tank has the shape of an inverted circular cone with height 7 m and base radius 3 m. It filled w water. Set up the integral form, don't evaluate it, for the work required to empty the tank by pumping all of the water to the top of a tank. (The density of water is 1000 kg/m³ and the acceleration due to gravity is 9.8 m/s²). 9800 7 S 9800 9800 49 9 - 49 * (7 — x)² dx 9 (7-2)²dx 49 (7 — x)² dx 7 9 [²3/10 S 49 -(7 — x)³ dx 7 9 √2/2 49 -(7 — x)² dx
A conical container of radius 8 ft and height 32 ft is filled to a height of 29 ft with a liquid weighing 64.4 lb/ft³. How much work will it take to pump the liquid to a level of 3 ft above the cone's rim? The amount of work required to pump the liquid to a level 3 ft above the rim of the tank is ft. lb. (Simplify your answer. Do not round until the final answer. Then round to the nearest tenth as needed.)
A soap bubble has diameter 2 cm. Calculate the work done to increase its diameter to 6 cm. surface tension of soap is 35 dynes/cm.
A cylindrical tank of radius 15 ft and height 6 ft is two-thirds filled with water. Find the work required to pump all the water over the upper rim. Enter the exact answer. Work = ? Edit ft · lb
A tank has the shape of an inverted circular cone with height 11 m and base radius 8 m. The tank is filled with water to a height of 9 m. Find the work required to empty the tank by pumping all of the water over the top of the tank. Use the fact that acceleration due to gravity is 9.8 m/sec² and the density of water is 1000 kg/m³. Round your answer to the nearest kilojoule. Provide your answer below: WUJ
3. For the hydraulic lift shown; A, Az The small piston area is 5 cm? and the large piston area is 50 cm?. The system is used to lift up a block of mass m = 300 Kg. Find the magnitude of the force F sufficient to do the work and find the work done on the block when it is lifted 120 cm.
Calculate the work (in Joules) required to pump all the water out of an inverted conical tank that has a radius of the base of 2 m, and a height of 4 m and is HALF FULL. The density of water is 3 1000 / kg m. Assume the tip of the conical tank is on the ground. HINT: Place the origin at the tip of the cone. Leave the answer in terms of ρ, g, and possibly π.
The vat shown in the accompanying figure contains water to a depth of xo 1.3 m. Find the work required to pump all the water to the top of the vat. Use 9810 N/m³ as the weight density of water. NOTE: Enter the exact answer. GIRIMARI. Work Mon 3 m 6 m 4 m
JA fuel oil tank is an upright cylinder, buried so that its circular top is 8 feet beneath ground level. The tank has a radius of 5 feet and is 15 feet high, although the current oil level is only 11 feet deep. Calculate the work required to pump all of the oil to the surface. Oil weighs 50 lb/ft. Work =