Consider the op-amp circuit shown below. You can assume the op-amp is ideal and has an infinite gain. R, R, ovo a. What is the value of ig? A (Give your answer to 3 s.f.) b. What is the value of the inverting input voltage v1? 数字 A (Give your answer to 3 s.f.) c. Using Kirchoffs Current Law (KCL), write an equation for the output voltage vo in terms of only the input voltage v a and the values of the resistances. You are not required to submit this equation as a part of this quiz but you will need the equation in the following questions. d. Given R2 = 10.4 kN, find the value of R¡ to give a gain of -55.5. 数字单位 (Give your answer to 3 s.f.) e. Given R1 = 4 kn and R, = 11.1 ka, find the value of the gain. 数字 (Give your answer to 3 s.f.)

Consider the op-amp circuit shown below. You can assume the op-amp is ideal and has an infinite gain. R, R, ovo a. What is the value of ig? A (Give your answer to 3 s.f.) b. What is the value of the inverting input voltage v1? 数字 A (Give your answer to 3 s.f.) c. Using Kirchoffs Current Law (KCL), write an equation for the output voltage vo in terms of only the input voltage v a and the values of the resistances. You are not required to submit this equation as a part of this quiz but you will need the equation in the following questions. d. Given R2 = 10.4 kN, find the value of R¡ to give a gain of -55.5. 数字单位 (Give your answer to 3 s.f.) e. Given R1 = 4 kn and R, = 11.1 ka, find the value of the gain. 数字 (Give your answer to 3 s.f.)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find an expression for the output voltage v, below. Assume an ideal op-amp. What mathematical operation does the circuit perform? R2 R
By using only two op-amps, design a circuit that can perform the following operation: Vo == Also, evaluate the given circuit equation. Show all the assumptions, calculation and the circuit illustration. Marking Scheme: Circuit Design Assumptions Calculation
The two input terminals of an op-amp are connected to voltage signals of strength 745µV and 740µV repectively. The gain of the op-amp in common mode is 50 and CMMR is 8&IB. Calculate the output voltage and % of error due to common mode.
Can you please explain and answer: Assume the opamp is power by -12V and +15V. What is the range of values for vs that does not saturateand the opamp remains in the linear region of operation?
You are hired as a technical consultant to model, design and analyze an efficient DC-DC buck converter for a solar PV battery charger as shown in the below figure. PV DC-DC Battery system Converter | MPPT algorithm Charge controller Given the following specifications for the design and analysis of a DC-DC Buck Converter: An input voltage of 15V < Vin < 20V and an output of Vout = 10V over a load range of 5w < Pout < 200W. Switching frequency is few = 500kHz. a) Design the inductor (L) and capacitor (C). The current ripple AiL should be below 5% of the average inductor current IL at the maximum load. The steady state ripple AVout is below 0.5 % of the steady-state value of the output voltage. For the designed L, find the value of Iout,crit at the boundary of DCM and CCM and then Plot Iout,crit vs. Vin . b) Design the rated values for switch, diode, and capacitor. Research and determine a manufacturer part number for your switch, diode, and capacitor. Provide data sheets for each. c)…
The triangular waveform in Figure 3(a) is applied to the input of the circuit in Figure 3(b).i) Find the output signal Vo(t) in terms of input signal Vi(t). (Assume op-amp is ideal)ii) Plot the output signal Vo(t).
1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
Operational amplifiers or Op-amps are essentially at the core of every analog device and perform varied functions and operations. Describe what an operational amplifier is and what its major applications are. Also describe what an ideal model for op amp is and some of the main assumptions made for an op amp to be modeled with an ideal model.
a. b. C. There is a dc-dc converter that provides isolation between input and output current. Identify the converter type and describe the operation. Draw the equivalent circuit to support the explanation. Assume the converter operates in continuous-current mode. Explain why a switched -mode dc-dc converter is better that a linear regulator. As an electrical engineer, you are required to design a chopper circuit with an output voltage of 10 V from a 30 V input with switching frequency of 50 kHz. The circuit is operated in continuous current, and output ripple voltage is less than 0.8% with resistance load of 30 Q. Assume the inductor value is 50 % larger than Lmin and assume ideal components for this design. Identify the chopper type and construct the circuit with IGBT as the power switching.
1) Op-amp limiting factors - Current Saturation U2 Vin R1 OUT OPAMP R2 RLoad The saturation output current for the above op-amp is +/- 15mA. For the following input signals, determine if the output appears as would be expected in an ideal circuit. Include sketches of the output voltage. a) R1 = 100, R2 = 900, an open circuit load, and Vin is 2Vpp triangle wave with zero offset voltage (Vmax 1V, Vmin = -1V) and a period of 2ms. b) R1 = 100, R2 = 900, a 1k load, and Vin is 2Vpp triangle wave with a 1V offset voltage (Vmax=2V, Vmin = 0V) and a period of 2ms. c) R1 = 100, R2 = 900, an open circuit load, and Vin is 4Vpp triangle wave with zero offset voltage (Vmax=2V, Vmin = -2V) and a period of 2ms.
Subject : Electronics Engineering Draw circuits for both inverting and non-inverting amplifier using op-amp. Derive the expression for the gain of an inverting amplifier
Subject: Electronics Engineering Draw the circuits of integrator and differentiator using op-amp. Derive the expression for output voltage.