Consider the following instance of the two-machine job shop with themakespan as objective (J2 || Cmax).Job236.7.81.4P1j1234103P2j38736.11RouteMi->M1->M2->M1->M2->M2->M1M2M2М2M1M2M1M11. Apply the shifting bottleneck heuristic to this two-machine job shop.2. Apply the SPT(1)-LPT(2) heuristic to this two-machine job shop.3. Compare the schedules found under (1), (2).2.

Consider the following instance of the two-machine job shop with the makespan as objective (J2 || Cmax). Job 3 Pij P2j Route 1 7 3 M1-> M2 2 2 11 M1-> M2 10 8 M2-> M1 4 3 7 5 12 3 M1-> M2-> M2 М1 6 3 6 M2-> М1 7 4 " M1 00 8 - 2 M2 1. Apply the shifting bottleneck heuristic to this two-machine job shop. 2. Apply the SPT(1)-LPT(2) heuristic to this two-machine job shop. 3. Compare the schedules found under (1), (2).

Consider the following instance of the two-machine job shop with the makespan as objective (J2 || Cmax). Job 3 Pij P2j Route 1 7 3 M1-> M2 2 2 11 M1-> M2 10 8 M2-> M1 4 3 7 5 12 3 M1-> M2-> M2 М1 6 3 6 M2-> М1 7 4 " M1 00 8 - 2 M2 1. Apply the shifting bottleneck heuristic to this two-machine job shop. 2. Apply the SPT(1)-LPT(2) heuristic to this two-machine job shop. 3. Compare the schedules found under (1), (2).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

is my input answer ture ??/ please check for me
2.10. Compute the long-term average throughput, cycle time and x-factors for this factory for fixed WIP levels of 1 through 5 for the four machine serial flow factory model below where the constant processing times are listed on the machines. As- sume that the factory starts with the configuration (N,0,0,0) for fixed WIP level N and no processing has occurred on any of the active jobs. out 2 3 new
8086 Microprocessor lab. | 9 Discussion: Two word - wide unsigned integers are stored at the memory addresses OA00 H and OA02 H respectively, Write an instruction sequence that computes and stores their sum, difference, product, and quotient then Store these results at consecutive memory locations starting at address 0A10 H in memory. To obtain the difference, subtract the integer at OA02 H from the integer at OA00 H. For the division, divide the integer at OA00H by the integer at OA02 H. Use register indirect relative addressing mode to store the various result.
3.Show the step-by-step process. Do not use shortcut methods. Make it as detailed as it can be. MAKE A DIAGRAM AND ENCODE THE ANSWER. DO NOT COPY CHEGG, THEY HAVE DIFFERENT GIVEN. HERE C=4 in
Let there be five jobs of the same type and one machine to get those jobs done. The processing time of the job on the machine and the time allowed for the job to be completed for each job are given in the table below. Job On the machinecompletion time(minute) To be finishedtime allowed(minute) 1 3 4 2 6 8 3 8 12 4 4 15 5 2 11 Apply the branch-and-boundary method step by step to order the jobs in a way that minimizes the total delay time. State the optimal solution clearly. Thank you so much.
Speed reduction, either through gearing or belt-pulley constructs, is an important element in motion system design. Similarly, converting rotary motion to linear motion is an important consideration. Considering a printer system driven by a stepper motor with 200 steps per revolution, construct a table that shows the relationships for: a. Position resolution of the print head vs. angular position of the motor. This translates to addressable print dots per mm vs. step angle. b. Print head speed (mm/S) vs. motor speed (Steps/S with rpm also noted) C. Frictional load at the print head (mN) vs. reflected torque at the motor (mNM) Mass of the print head vs. reflected inertia to the motor d. Use GR for Speed Reduction, r (mm) for the radius of the drive pulley, and m (grams) for print-head mass.. Belt Actuator Load Drive Pulley Secondary Pulley Linear Guide Belt Primary Pulley Motor
Find the solution to Processing 8 Jobs Through 3 Machines Problem. Job 1 2 3 4 5 6 78 7 11 16 11 21 Machine M, 5 6 2 3 492| 6 Machine M 8 10 6 Machine M,| 14 20 30 26 35 9 10 23
Please solve step by step as following the problem instructions
Needs Complete typed solution with 100 % accuracy
Let there be five jobs of the same type and one machine to get those jobs done. The processing time of the job on the machine and the time allowed for the job to be completed for each job are given in the table below. Job On the machinecompletion time(minute) Allowed To be finishedtime (minute) 1 3 4 2 6 8 3 8 12 4 4 15 5 2 11 Apply the branch-and-boundary method step by step to order the jobs in a way that minimizes the total delay time. State the optimal solution clearly. Thank you so much.
= Consider a four aisle AS/RS in which an S/R machine is used for each aisle. The length of the storage aisle 85 m and its height = 14 m. Suppose horizontal and vertical speeds of the S/R machine are 61 m/min and 23 m/min, respectively. The S/R machine requires 20 s to accomplish a P&D operation. The aisles in the AS/RS will be organized to follow a class-based dedicated storage strategy. There will be two classes, according to activity level. The more active stock is stored in the half of the rack system that is located closest to the input/output station, and the less active stock is stored in the other half of the rack system farther away from the input/output station. Within each half of the rack system, random storage is used. The more active stock accounts for 80% of the transactions, and the less active stock accounts for the remaining 20%. Assume that system utilization = 90%, and the number of single-command cycles = the number of dual-command cycles. Determine the throughput…
Solve the Following Problem. JOB SEQUENCE "N" JOBS- "3" MACHINE JOB 1 2 4 A 10 6. 7 11 В 6. 2 3 4 4 9.