which is correct?23.1% , 76.2 %, 45.2% , 33.4% , 49.0% Consider the binary alloy phase diagram shown schematically below. The left-hand side denotes phasea, and the right-hand side the phase ß. The intermediate region is a coexistence regime with both aand 3 phases. The points 1 in the coexistence region is at 24 wt% A. If the points on the phaseboundaries L- and R- are at 19 wt% A and 40 wt % A, respectively, what is the fraction of a phase atA-B binary alloy1?T(°C)14001100αL20%Coexistence regionR40 %Weight % AB

Given that: For the isotherm L-1-R, L is 19% of A 1 is 24% of A R is 40% of A Phase α exists on left…

Consider the binary alloy phase diagram shown schematically below. The left-hand side denotes phase a, and the right-hand side the phase ß. The intermediate region is a coexistence regime with both a and ß phases. The points 1 in the coexistence region is at 24 wt% A. If the points on the phase boundaries L- and R- are at 19 wt% A and 40 wt% A, respectively, what is the fraction of a phase at 1? T(°C) 1400 1100 α A-B binary alloy L 20 % Coexistence region Weight % A R 40 % В

Consider the binary alloy phase diagram shown schematically below. The left-hand side denotes phase a, and the right-hand side the phase ß. The intermediate region is a coexistence regime with both a and ß phases. The points 1 in the coexistence region is at 24 wt% A. If the points on the phase boundaries L- and R- are at 19 wt% A and 40 wt% A, respectively, what is the fraction of a phase at 1? T(°C) 1400 1100 α A-B binary alloy L 20 % Coexistence region Weight % A R 40 % В

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1/ The figure below shows the phase equilibrium diagram for copper and silver Answer the following paragraphs? Conpostin a% 39 o = « & o Tepertue (F) @ Composttan (w5 ) 0 1- define pointe E? 2- define pointe B? 3- define the line AE? 4- define the line BG? 5- define the line FG?
An alloy system consists of two metals A&B which are soluble in each other in all proportions in the liquid state, but completely insoluble in the solid state. The melting point of metal A is 425°C and B is 375°C. The lowest melting point (Eutectic) is 230°C at 40%B. For a 30 wt% A alloy at 300°C, the phases weight are O 0.4 kg B and 0.6 kg Liquid O 0.21 kg A and 0.789 kg Liquid 0.35 kg B and 0.65 kg Liquid 0.82 kg A and 0.18 kg Liquid
An alloy system consists of two metals A&B which are soluble in each other in all proportions in the liquid state, but completely insoluble in the solid state. The melting point of metal A is 425°C and B is 375°C. The lowest melting point (Eutectic) is 230°C at 40%B. For a 40 wt% B alloy at 450°C, the phases weight are 0 kg A, 0 kg B and 1 kg Liquid 0 kg Liquid and 1 kg A 0.5 kg B& 0.5 kg A O 0.35 kg A and 0.65 kg B
Referring to Figure 1, please answer the following [NOTE: SHOW YOUR WORK on Figure 1]:a. provide the specific name for the phase boundary lines denoted by A and B. b. identify the phases present at equilibrium in the phase fields denoted by C, D, and E. c. identify the specific name for the point denoted by F. d. What is the maximum solid solubility of Mg in Al? At what temperature does it occur? e. An Al-Mg alloy (10 wt% Mg, 90 wt% Al) is heated slowly (to insure equilibrium) from a temperature of 200 C: i. At what temperature does the first liquid phase form? ii. What is the composition of the liquid phase at the temperature in part i.? iii. At what temperature does complete melting (no solid phase remaining) occur? iv. What is the composition of the last solid remaining prior to complete melting? f. Using the equilibrium phase diagram of Figure 1, identify the phases present, their compositions, and their relative mass fractions at equilibrium for a 70 wt% Mg – 30 wt% Al…
A 45 wt% Pb-55 wt% Mg alloy is rapidly quenched to room temperature from an elevated temperature in such a way that the high- temperature microstructure is preserved. This microstructure is found to consist of the a phase and Mg2Pb, having respective mass fractions of 0.65 and 0.35. Determine the approximate temperature from which the alloy was quenched. Use Animated Figure. °℃
Consider the phase diagram below. The three points A, B, and C are at concentrations of 26.4, 31.3, and 34 wt% Ni respectively. The ends of the tie line are at C1 = 25% wt% Ni and C2 = 35 wt% Ni. What are the weight fractions of the alpha phase at A and the L phase at B, as well as the alpha phase/L phase ratio at C? T(°C) 1300 L (liquid) 1200 20 A B C L + a C1 S liquidus L + a solidus a (solid) 50 wt% Ni a. Walpha=0.21; WL=0.33; Walpha/WL = 13.17 b. Walpha=0.09; WL=0.32; Walpha/WL = 15.00 c. Walpha=0.07; WL=0.46; Walpha/WL = 11.17 d. Walpha=0.14; WL=0.37; Walpha/WL = 9.00
Using the Ti-Cu phase diagram, if you start with 100 kg of a Ti-Cu mixture at 3000C and 10 wt. % Cu and cool down very slowly to points A (1400 C), B (950 C), C (800 C), and D (500 C), determine what phases are present at each letter, determine the compositions for each phase, and determine the weight in each phase. Point A): Phase(s) present Weight % of Cu in each phaseWeight of each phase Point B): Phase(s) present Weight % of Cu in each phaseWeight of each phase Point C): Phase(s) present Weight % of Cu in each phaseWeight of each phase Point D): Phase(s) present Weight % of Cu in each phaseWeight of each phase
ASAP
3. G T A A ४ L+d Liquid L L+α! d+d' al в Sotid G Liquid d B A For the eutectic phase diagram shown above at the temperature given by the dotted line, the two Gibbs free energy diagrams are equally valid. Explain the difference between the two and why they are both valid. ✓ B
Using the Ti-Cu phase diagram, if you start with 100 kg of a Ti-Cu mixture at 3000C and 10 wt. % Cu and cool down very slowly to point D (500 C), determine what phases are present at each letter, determine the compositions for each phase, and determine theweight in each phase. Point D): Phase(s) present Weight % of Cu in each phaseWeight of each phase
2. a) How many kilograms of nickel must be added to 1.75 kg of copper to yield a liquidus temperature of 1300 °C? b) How many kilograms of nickel must be added to 5.43 kg of copper to yield a solidus temperature of 1200 °C? c) The solidus and liquidus temperatures for the copper-gold system are given here. Construct the phase diagram for this system and label each region. Composition (wt.% Au) Solidus Temperature (C) Liquidus Temperature (C) 1085 1085 1019 972 20 1042 996 946 40 60 934 80 911 911 90 928 942 95 974 984 100 1064 1064
1. Calculate the mass fraction fα of α of Fe-0.45% C at 750 °C by the lever rule. Draw the schematic of microstructure of Fe-0.45% C at 20°C which was gradually cooled from 750°C, and describe the name of each phase.