Consider one-dimensional transient heat conduction in a plane wall with thickness L and constant properties. The boundary and initial conditions are given in Figure 2, and are constants. There is no heat generation within the wall. Find the temperature, T(x,t), within the wall

Consider one-dimensional transient heat conduction in a plane wall with thickness L and constant properties. The boundary and initial conditions are given in Figure 2, and are constants. There is no heat generation within the wall. Find the temperature, T(x,t), within the wall

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.63P

See similar textbooks

Similar questions

Which formula is used to calculate the heat conduction in the AXIAL direction in a vertically located pipe segment whose inner and outer surfaces are perfectly insulated. Here r, is inner radius, r, outer radius, Tri pipe inner surface temperature, Tro pipe outer surface temperature, L is the length of the pipe, T the temperature on the lower surface, Ty the temperature on upper surface. Tu r; Tro r
A plane wall of thickness 8cm and thermal conductivity k=5W/mK experiences uniform volumetric heat generation, while convection heat transfer occurs at both of its surfaces (x= -L, x= + L), each of which is exposed to a fluid of temperature T∞ = 20˚C. The origin of the x-coordinate is at the midplane of the wall. Under steady-state conditions, the temperature distribution in the wall is of the form T(˚C) = a + bx - cx^2, where x is in meters, a =86˚C, b = -500˚C/m, and c=4459. 1) Heat Flux Entering the wall is ? 2) Temperature at the left face is /
The 1-4-7 surface in the section shown in the figure is insulated. The heat transfer coefficient on the surface 1-2-3 is 28W /m? °C. The thermal conductivity of the solid material is 5.2W / m°C. Calculate the temperatures of the points 1, 2, 4 and 5 using the finite difference method. insulated T = 0°C 30 cm h = 28 W/m?. C+ 30 cm T, = T3 = T, = 38°C T3 = T6 = 10°C 00
4x F2 # 3 E 4, F3 54 $ R F4 Ac = 1m² ▬ H DII x= 1 m (4) Consider a wall (as shown above) of thickness L-1 m and thermal conductivity k-1 W/m-K. The left (x=0) and the right (x=1 m) surfaces of the wall are subject to convection with a convectional heat transfer coefficient h= 1 W/m²K and an ambient temperature T. 1 K. There is no heat generation inside the wall. You may assume 1-D heat transfer, steady state condition, and neglect any thermal contact resistance. Find T(x). % To,1 = 1 K h₁ = 1 W/m²K 5 Q Search F5 T T₁ A 6 x=0 F6 à = 0 W/m³ k= 1W/mK L=1m Y 994 F7 & 7 T₂ U Ton2 = 1 K h₂ = 1 W/m²K1 PrtScn F8 Page of 7 ) 0 PgUp F11 P
A 1-D conduction heat transfer problem with internal energy generation is governed by the following equation: +-= dx2 =0 W where è = 5E5 and k = 32 If you are given the following node diagram with a spacing of Ax = .02m and know that m-K T = 611K and T, = 600K, write the general equation for these internal nodes in finite difference form and determine the temperature at nodes 3 and 4. Insulated Ar , T For the answer window, enter the temperature at node 4 in Kelvin (K). Your Answer: EN SORN Answer units Pri qu) 232 PM 4/27/2022 99+ 66°F Sunny a . 20 ENLARGED oW TEXTURE PRT SCR IOS DEL F8 F10 F12 BACKSPACE num - %3D LOCK HOME PGUP 170
Find the two-dimensional temperature distribution T(x,y) and midplane temperature T(B/2,W/2) under steady state condition. The density, conductivity and specific heat of the material are p=(1200*32)kg/mº, k=400 W/m.K, and cp=2500 J/kg.K, respectively. A uniform heat flux 9" =1000 W/m² is applied to the upper surface. The right and left surfaces are also kept at 0°C. Bottom surface is insulated. 9" (W/m) T=0°C T=0°C W=(10*32)cm B=(30*32)cm
1 . A long cylindrical shell outer radius R₂ = 2 cm is shown in cylindrical shell is temperature Ti=10 c° and outer wall at Constant temperature T₂ = 20 C° Calculate the temperature at r= 1.5 cm (Consider conduction only) Assumptions: system is Thermal in Given: The of inner and the figure. The radial + The differential The system is: J²T dr² r maintained at steady state conductivity, K = 22.5 w/mc, system follows Fourier's law of heat Heat loss in axial direction is negligible. JT dr radius Ri=1cm Length L=lom inner Wall Constant is maintained = 0 of is Ti RI R₂ constant. conduction. equation representing Tz
3. For two dimension heat conduction in a plate as shown in figure 3, find the temperature distribution T (x,y) by solving the boundary value problem. a2T + ду? Use the steady state heat conduction equation as: Ty=n = 1 Tx=0 = 1 H = T Tx=n = 1 L = TT y Ty=o = 0 Figure 3
The initial temperature distribution of a 5 cm long stick is given by the following function. The circumference of the rod in question is completely insulated, but both ends are kept at a temperature of 0 °C. Obtain the heat conduction along the rod as a function of time and position ? (x = 1.752 cm²/s for the bar in question) 100 A) T(x1) = 1 Sin ().e(-1,752 (³¹)+(sin().e (-1,752 (²) ₁ + 1 3π TC3 .....) 100 t + ··· ....... 13) T(x,t) = 200 Sin ().e(-1,752 (²t) + (sin (3). e (-1,752 (7) ²) t B) 3/3 t + …............) C) T(x.t) = 200 Sin ().e(-1,752 (²t) (sin().e(-1,752 (7) ²) t – D) T(x,t) = 200 Sin ().e(-1,752 (²)-(sin().e (-1,752 (²7) ²) t E) T(x.t)=(Sin().e(-1,752 (²t)-(sin().e(-1,752 (²) t+ t + ··· .........) t +.... t + ··· .........) …..)
The heat flow per unit length of a thick cylindrical pipe is 772 W per meter. The pipe has radii ri = 12 cm, ro = 24 cm, outside surface temperature, To = 95 deg C and k = 0.05 + 0.0008T where T is in deg C and k is in W/(m K). Find the inside surface temperature of the pipe, assuming steady state conditions and accounting for the variation of thermal conductivity with temperature. Also determine the temperature of a point midway to the inside and outside radius.
ähäi 100 Q1: Consider a long resistance wire of radius r1 = 0.3 cm and thermal conductivity kwire = %3D 17 W/m•°C in which heat is generated uniformly as a result of resistance heating at a constant rate of q = 100 W/cm3 (see Figure below). The wire is embedded in a 1-cm- thick layer of ceramic whose thermal conductivity is kceramic =1 W/m.°C. If the center temperature of the resistance wire is measured to be Tc= 705°C, determine the temperatures at the surface of ceramic and the interface of the wire and the ceramic layer under steady conditions.
You are asked to estimate the maximum human body temperature if the metabolic heat produced in your body could escape only by tissue conduction and later on the surface by convection. Simplify the human body as a cylinder of L=1.8 m in height and ro= 0.15 m in radius. Further, simplify the heat transfer process inside the human body as a 1-D situation when the temperature only depends on the radial coordinater from the centerline. The governing dT +q""=0 dr equation is written as 1 d k- r dr r = 0, dT dr =0 dT r=ro -k -=h(T-T) dr (k-0.5 W/m°C), ro is the radius of the cylinder (0.15 m), h is the convection coefficient at the skin surface (15 W/m² °C), Tair is the air temperature (30°C). q" is the average volumetric heat generation rate in the body (W/m³) and is defined as heat generated per unit volume per second. The 1-D (radial) temperature distribution can be derived as: T(r) = q"¹'r² qr qr. + 4k 2h + 4k +T , where k is thermal conductivity of tissue air (A) q" can be calculated…