Consider a 10-m-long smooth rectangular tube, with a = 50 mm and b = 25 mm, that is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C.

Consider a 10-m-long smooth rectangular tube, with a = 50 mm and b = 25 mm, that is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.43P: 7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s...

See similar textbooks

Similar questions

Consider a pipe with a length of 25 m and diameter of 5 cm. The surface temperature of the pipe is constant at 150°C.Oil at 20°C is passing though this pipe with a mass flow rate of 0.5 kg/s. determine (a) the temperature of the oil at the exit and (b) the total heat transfer rate. Note. Report your solution step by step and clearly.
Liquid glycerin is flowing through a 25-mm-diameter and 10-m-long tube. The liquid glycerin enters the tube at 10°C with a mass flow rate of 0,2 kg/s. If the outlet mean temperature is 60°C and the tube surface temperature is constant, determine the surface temperature of the tube.
Liquid water enters a 10-m-long smooth rectangular tube with a 50 mm and b = 25 mm. The surface temperature is kept constant, and water enters the tube at 20°C with a mass flow rate of 0.25 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C Find the pumping power. Te
Consider a 10-m-long smooth rectangular tube, with a = 50 mm and b = 25 mm, that is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.025 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C. (Nu = 3.39)
Consider a 10-m-long smooth rectangular tube, with a = 50 mm and b= 25 mm, that is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.027 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C. (Nu = 3.39) "C
Liquid water enters a 10-m-long smooth rectangular tube with a 50 mm and b = 25 mm. The surface temperature is kept constant, and water enters the tube at 20°C with a mass flow rate of 0.25 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C Find the pumping power.
One house owner with a pond on his property has decided to use the pond water to cool his house. His idea is to flow air through a thin smooth 10-cm-diameter copper tube that could be submerged into the pond. The water in the pond, at few meters below the surface is typically maintained at a constant temperature of 15°C. If he assumes the air (~1 atm) entering the copper tube at a mean temperature of 30°C with an average velocity of 2.5 m/s, determine the necessary copper tube length that would be needed so that the outlet mean temperature of the air is 20°C. You may consider the convection heat transfer coefficient of 1000 W/m2·K on the outer surface of the copper tube, between the pond water and copper tube. Since the copper tube is thin, the conduction resistance of the tube wall may be neglected.
In a manufacturing plant that produces cosmetic products, glycerin is being heated by flowing through a 25-mm-diameter and 10-m-long tube. With a mass flow rate of 0.5 kg/s, the flow of glycerin enters the tube at 25°C. The tube surface is maintained at a constant surface temperature of 140°C. Determine the outlet mean temperature and the total rate of heat transfer for the tube. Evaluate the properties for glycerin at 30°C.
Water with a mass flow rate of 0.002 kg/s at 18oC flows inside a tube while the flow is already developed hydrodynamically. The inner diameter of the tube is 1.5 cm, and the inner pipe wall temperature is maintained uniformly at 125oC. Calculate the required tube length to increase the water temperature to 82oC.
Consider a 25-mm-diameter and 15-m-long smooth tube that is used for heating fluids. The wall is heated electrically to provide a constant surface heat flux along the entire tube. Fluids enter the tube at 50°C and exit at 150°C. If the mass flow rate is maintained at 0.01 kg/s, determine the convection heat transfer coefficients at the tube outlet for water, engine oil, and liquid mercury.
Liquid water flows in a thin-walled circular tube at a mass flow rate of 11 g/s. The water enters the tube at 60°C, where it is heated at a rate of 3.8 kW. The tube is circular with a length of 2.5 m and an inner diameter of 25 mm. The tube surface is maintained at a constant temperature. At the tube exit, a hydrogenated nitrile rubber (HNBR) o-ring is attached to the tube's outer surface. The maximum temperature permitted for the o-ring is 150°C. Is the HNBR o-ring suitable for this operation? The fluid properties at 100°C are cp= 4217 J/kg-K, k= 0.679 W/m-K, µ = 0.282 × 103 kg/m.s, and Pr = 1.75. Is this a reasonable temperature at which to evaluate the fluid properties?
Consider a 50-mm-diameter and 25-m-long smooth tube that is maintained at a constant surface temperature. Fluids enter the tube at 30oC with a mass flow rate of 0.02 kg/s. Determine the tube surface temperatures necessary to heat water, engine oil, and liquid mercury to the desired outlet tem-perature of 170o