do both question please ListenCompute the hydraulic radius for the channel shown in if the water depth is 2.50 m,in meters to the nearest 100th.2.5 m20.5 m0.6 m1.0 m GivenA storm drainage channel in a city where heavy sudden rains occur has the shapeshown in the figure below. It is made of unfinished concrete and has a slope of 0.75percent. During normal times, the water remains in the small rectangular section. Theupper section allows large volumes to be carried by the channel.RequiredDetermine the normal discharge for depth of 2.5 m in m3/s, to the nearest 10th.2.5 m20.5 m0.6 m1.0 mYour Answer:

Given:- Water depth=2.5 mSlope, S=0.75 % =0.7510000 =75×10-4Manings…

Answered: Compute the hydraulic radius for the…

Compute the hydraulic radius for the channel shown in if the water depth is 2.50 m, in meters to the nearest 100th. 2.5 m 0.5 m 0.6 m 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4.65. Derive an expression relating the conjugate depths in a hydraulic jump when the slope of the channel is equal to So. [Hint: Assume that the length of the jump is equal to 5y2, and that the shape of the jump between the upstream and downstream depths can be approximated by a trapezoid.]
Water is flowing in a 3m wide rectangular channel at a depth of 360mm. A hydraulic jump occurs and the depth downstream from the jump is 1.3m. determine the discharge in m^3/s. Group of answer choices 7.51.95.9 6.3
*hydraulics *Use handwritten Water Flows uniformly at a steady rate of 0.40 m3/s in a very long triangular flume which has side slopes of 1:1. the bottom of the flume is on a slope of 0.006 and n=0.012. Determine the critical depth of flow Choices: A.) 0.504 m B.) 0.604 m C.) 0.704 m D.) 0.804 m
A concrete lined (n=0.013) trapezoidal channel has a bed slope of 0.00152 and it carries a discharge of 8 m³/s. What is the normal depth based on the most hydraulically efficient section? Select an answer and submit. For keyboard navigation, use the up/down arrow keys to select an answer. a b с d 1.2 m 1.4 m 1.6 m 1.8 m.
A horizontal channel with a trapezoidal cross-section has a bottom width of 5 m, sidewall slope of 1V:2H, and discharge of Q = 10.85 m³/s. The water level was kept constant at the gate to 0.25 m to form a hydraulic jump in the channel. The conjugate depth based on the graphical method (Figure 6-7) is: Select an answer and submit. For keyboard navigation, use the up/down arrow keys to select an answer. a b с d Vapa 1.50 m 1.75 m 2.10 m 2.25 m 14 12 10 60 1 50 S 100 10 150 20 250 300 Q/(my₁²(gy₁)¹/2) Figure 6-7: Prediction of conjugate depth ratio in hydraulic jumps for trapezoidal cross-sections. 200 30 350 B/(my) = 50 400 450 500
A hydraulic jump is formed in a hydraulic laboratory with a 0.6-m wide rectangular flume. The water depth at the gate is one inch and the discharge is 45 L/s. What is the required tailwater depth to stabilize the jump and what is the approximate length of the jump? Select an answer and submit. For keyboard navigation, use the up/down arrow keys to select an answer. a b с d 0.20 m, 1.2 m 0.50m, 3 m 0.15 m, 0.9 m 0.30 m, 1.8 m
*hydraulics *use handwritten A rectangular channel 5.50 m wide and 1.30 m deep is laid on a uniform slope of 0.002. The roughness coefficient of the channel is 0.013. 1.) Which of the following most nearly gives the rate of flow in the channel in m^3/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67 2.) Which of the following most nearly gives the saving’s in lining per meter length of channel that could have been offered by using the most efficient rectangular section but adhering to the same flow capacity and slope in m^2/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67 3.) Which of the following most nearly gives the savings in earth excavation per meter length of channel that could have been offered by using the most efficient rectangular Section but adhering to the same flow capacity and slope in m^3/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67
Calculate for the hydraulic gradient if the pressure at point A is 1587ZN and 13577N for point B. The measured value of distance Lis 3m and height h is 5m. A paedaas. seepage
Plz, solve the parts of this question. Hydraulics. My Reg.No: 5395 Question # 02:a). The flow rate in a long rectangular channel (n = 0.014) is equal to the last three digits of your registration number in cubic feet per second. The channel is 12ft wide and there is an abrupt change in slope from 0.0019 to 0.018. PLOT a figure showing normal depths, critical depths and water surface profiles? b).Using Rayleigh’s procedure, PRODUCE an expression for the discharge over a spillway (Q) which is a function of head above spillway (H), height of spillway (h), velocity of flow (V) and acceleration due to gravity (g)?
it is the depth difference between the waterlevel measured after some time during borehole pumping and the water level measured before pumping started. A. dynamic water level B. static water level OC. recovery water level D. drawdown
Water flows in a 1.5-m wide rectangular channel with a constant bed slope So = 0.144 (see figure below). Calculate the horizontal distance from point 1 with depth of y₁ = 0.68m to point 2 with depth of 0.45m. The bed slope is small and hence you can assume that the distance between points 1 and 2 along the channel bed is equal to the horizontal distance Az The average friction slope is 0.062 and the flow rate is 0.8 m³/s. Ax 2.805 m
Q-2 Water flows through a vertical contraction (venturi) section. Piezometers are attached to the upstream pipe and minimum area section as shown. The velocity in the pipe is 3 m/s. The difference in elevation between the two water levels in the piezometers is 15 cm. What is the velocity at the minimum area? 15 cm 3 mis