Complete the table below. STATION BM1 A B C D E F BM2 BS 1.548 1.423 2.522 2.883 2.779 1.272 Highest elev of the line of sight Station with the highest elevation (excluding BM1 & BM2) Lowest rod reading Station with the Highest BS Lowest Elevation HI 354.348 356.134 356.492 357.732 358.148 358.392 FS 1.339 1.065 1.439 2.726 1.028 1.761 ELEV 353.009 355.069 355.053 354.849 355.369 356.631

Complete the table below. STATION BM1 A B C D E F BM2 BS 1.548 1.423 2.522 2.883 2.779 1.272 Highest elev of the line of sight Station with the highest elevation (excluding BM1 & BM2) Lowest rod reading Station with the Highest BS Lowest Elevation HI 354.348 356.134 356.492 357.732 358.148 358.392 FS 1.339 1.065 1.439 2.726 1.028 1.761 ELEV 353.009 355.069 355.053 354.849 355.369 356.631

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

On the drawing below, the virtual condition of the 4 holes is? O .450 .375 O.395 O .020 D O .430 Ø3.000 .020 0 10 45° 4X Ø.395-.430 Ø.500-.510 Ø.020MABMCM +0.010M ADM Ø2.000 .375-.395 4.000MABM C A 0.005MA B
Q3: A: Draw the diagram of traverse classification. B: In closed traverse ABCD. The partial coordinates were known as shown below. Determine its area by DMD method. 04 N Dofland OWODY dienstl it with (nm) dinostim Mem. AB BC CD DA ΔΧ 40 -80 -50 AY 60 100 -70
Determine the force of all members using METHOD OF JOINT. Answer in 3 decimal places only. TRUSS MEMBERS ● FORCE COMPRESSION OR TENSION
h er 6. Calculate the height difference of level surveying and the elevation of point B in Tab. 2-6. Station number Surveying point HA I II a IN BM. A TP₁ TP₁ TP₂ TP₁ TP, TP₁ B TP MSL Σa-2b= II Back rod reading (mm) 1780 1651 1167 b₂ 1726 Level surveying record Front rod reading (mm) TP₂ E 1200 1050 1789 1448 TP, & (height difference) (m) + da TP Tab. 2-6 H(m) 20,000
If the 4 holes in the drawing below are produced at .410" in diameter, what is the total positional tolerance of the holes? O .040 O .020 O .035 D O .410 Ø3.000 .020 45° 4X Ø.395-.430 Ø.500-.510 0.020MABMCM +0.010M ADM -.375-.395 +.000MABM C Ø2.000 A 0.005MA B
Transit is set up at A observeda stadia intercept of 2.2 m at a verticalangle of +1823’. The stadia interval factor ofthe instrument used is 95.5 and stadiaconstant of 0.3 m. If the height of instrumentis 1.62 m, and the rod reading is 1.95 m.Determine the horizontal distance from thetransit set up A to the rod at point B. a. 201.44 m c. 198.45 b. 189.48 m d. 186.56 m
Bearing or Azimuth of Line AB: ____________________ Sta Occ Sta Obs Dist (m) Mean Dist Observed Interior Angle Corr Adjusted Interior Angle Direct Reversed Mean A E 11.55 102°57 B 13.20 B A 13.20 C 17.42 C B 17.42 D 10.00 D C 10.00 E 13.90 E D 13.90 A 11.55
5:18 M LAZ Zoom Leave V ERIALS/1ST%20sem/CE%20PC%20313/Structural%20Analysis%20by%20Aslam%20.. Sign in ... TU IL TO IL El = constant E = 29,000 ksi I = 4,000 in.4 FIG. P6.16, P6.42 64 k t point A C В 9 ft 9 ft- -18 ft El = constant E = 29,000 ksi I = 500 in.4 FIG. P6.17, P6.43 6.18 through 6.22 Determine the smallest moment of inertia I required for the beam shown, so that its maximum deflection does not execed the limit of 1/360 of the span length (i.e., Amax < L/360). Use the moment-area method. C 60 kN 300 kN - m A B. .1 Unmute Start Video Share Participants More II
200kg 12 wedge A 2865 N B) 2685 N 2391 N
Dizr. 36l {,0K/s Asiacell bläi 3 Reciprocal ranging is employed when * both the ends are inaccessible. O the two ends of a line are not intervisible. the ends of the line are not visible even from intermediate points. one end of a line is inaccessible. O bläs 6 Find the horizontal distance AD. If BD and CD were 30m and .80m respectively B 190° 3D
STATIOΝ DIRECT DOUBLE МEAN REMARKS DEFL. DEFL. DEFL. Azimuth 111 - 112 = 121° 21' R (+) R (+) R (+) 111 147° 01' 293° 59' 112 116° 11' 232° 22' 113 157° 5' 314° 02' 114 59° 2' 119° 8' L (-) ΣAngle Check (Closed Traverse Only): Misclosure by sum of deflection angles: Misclosure by azimuth calculation: (show work for azimuth calculations separately) Note: Add the deflection angles algebraically ( R = + Angle, L = - Angle)
Find the equal height of towers at triangulation stations A and C so that line AC will clear theelevated ground between A and C by 6m. with the instrument set at point B, the observedvertical angle to ground station A is 0 0 55’ and the vertical angle to ground station C is 0 0 48’.Elevation of A is 237m. Distance AB is 10km and distance of BC is 8.7km. Yhe instrument set-upat B is 2.7m above the ground. Use hcr= 0.067k ^2