Collars A and B are pin-connected to bar ABD and can slide along fixed rods. Knowing that, at the instant shown, the velocity of A is a constant 1.8 m/s to the right, determine distance between collar A and the instantaneous center of the bar ABD in (m) 300 mm 300 mm 60° 60° Select one: a. 0.6 b. 0.45 O c. 0.3

Collars A and B are pin-connected to bar ABD and can slide along fixed rods. Knowing that, at the instant shown, the velocity of A is a constant 1.8 m/s to the right, determine distance between collar A and the instantaneous center of the bar ABD in (m) 300 mm 300 mm 60° 60° Select one: a. 0.6 b. 0.45 O c. 0.3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. In the figure below, a force F passing through C causes a clockwise moment of 217N-m about A and a clockwise moment of 96N-m about B. Determine the force and its x-intercept ix. A 2 m Fx+c Action Line of F .....I.....-. 3 m F, Fx D в ix IF, 5 m.
Q/ The (200N) block shown in Fig . Has impending motion up the plane .Coused by e isjall dåg le the Horizontal force Lii 5 gå of ( 400N ). Determine the coefficient of static friction between the contact surfaces alial l. 400N 200N 300
Force P with 5.05 kN magnitude acts along the parallelepipeds diagonal CE, pointing towards E 290 mm 290 mm 145 mm Determine the magnitude of the moment of Pabout the following Ines in N-m. (a) Ine OA N-m (b) ine O8 N- m (c) Ine AB N-m (d) Ine BF N-m (e) ine BG N-m (r) Ine DG N-m (a) Ine 0D N-m (h) Ine OC N-m (1) ine EF N-m (1) Ine OF
Homeworks: A steel shaft of two segments AB and BC which are rigidly fastened at B Determine: 1) Reactions at A and C. 2) Maximum angle of rotation. 1000N. mn/mm 4m 100mm S0mm 5mm
Rotation of bar OA is controlled by the lead screw which imparts a horizontal velocity v to collar C and causes pin P to travel along the smooth slot. Determine the values of and dot theta where r= overline OP if h = 160mm x = 120mm and v = 25mm / s at the instant represented.
The rollers attached to rod AB can slide freely along the horizontal floor and the vertical plane. At the instant shown, end A has a downward velocity of 2.5 ft/s. Determine (a) the angular velocity of the rod and (b) the velocity of end B of the rod. A В 12 in 20 in 16 in
3. Collar P is attached to rod AP which rotates at a counterclockwise angular velocity of 4 rad/s and a clockwise angular acceleration of 5 rad/s². Determine at the instant shown (a) the angular acceleration of bar BD and (b) the acceleration of pin P relative to bar BD. B 45° 10 in 10 in D
wo (a) Obtain the total elongation of a steel bar of cross-sectional Area 1250mm² acted 2. by forces indicated in the diagram below. E=205,000N/mm2 15N- SN 20N.. 40N 15N 1.5m 1.5m 3m 1m
The beam is having a fixed support in one end, and 2 roller support 3m and 7m from the fixed support, respectively. Solve the following: 50kN 25kN/m 3m 2m 2m i.What is the reaction at B? a. 43.50kN c. 76.19kN b. 32.69kN d. 66.23kN ii.What is the reaction at C? c. 17.31kN d. 16.12kN a. 14.77KN b. 18.22kN iii.What is the moment reaction at A? a. 12.75kN-m c. 15.12kN-m b. 23.12kN-m d. 8.44kN-m
Example An experimental device imparts a force of magni- tude F 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the 900 mm 700 mm moments of the force F about point O and about point B. Finally, locate, from the base at O, a point C on the ground where the force imparts zero moment. 300 mm 3050 mm Ans. Mb= 166.5 N.m Mo= 123.75 N.m Location C w.r.t O = 687.5 mm to the left O
ASAP
If bar AB has an angular velocity w AB = 4 rad/s, determine the velocity of the slider block C at the instant shown. 30° 200 mm B 150 mm WAB = 4 rad/s 60°