Calculate the nominal and reduced moment capacities for the indicated concrete sections. Given: f'c-280 kg/ cm² and fy=4,200 kg/cm². 30.5 cm 6.35 cm 8.9 cm 2 #9 T 4 #9 h = 92 cm 6 #9 6 #9 82.55 cm 6 #9

Calculate the nominal and reduced moment capacities for the indicated concrete sections. Given: f'c-280 kg/ cm² and fy=4,200 kg/cm². 30.5 cm 6.35 cm 8.9 cm 2 #9 T 4 #9 h = 92 cm 6 #9 6 #9 82.55 cm 6 #9

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the truss and loading shown below, determine the stress at member AB if Pu = 18.375 Kips and its area is 23 in². Assume that the truss are simply supported at joint M and E. Express your answer in ksi. Use three decimal places. RM Pu Pu 0 Pu Pu 8@10' 80' Pu B Pu L K J I H G 8@10' 80' Pu D LL F E RE
Given the truss and loading shown below, determine the stress at member Al if Pµ = 18.375 Kips and its area is 16 in². Assume that the truss are simply supported at joint M and E. Express your answer in ksi. Use three decimal places. L RM Pu N Pu LK Pu Pu 8@10' = 80' Pu B Pu Pu D J I H G F 8@10' 80' RE
twork Analyze the truss shown using method of joints. The following are the values of the forces: P = 10KN Q = 20 kN R = 30 kN %3D centives Determine the following: CAR a. AE [Select] ements ents b. ČE [ Select] ons C. CD [Select] 40 kN 3 m F F 20 kN + 20 kN E 2 m rations C 5 m Drive A 65 2 5 5 m m m TI Pro P.
A reinforce d rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1layer at the tension side. The beam has a stirrup with diameter of 10 mm. Use f c'= 28 M Pa and fy = 420 M Pa. Given: b=532.5mm d=877.5mm Fy = 420 MPa F'c = 28 MPa L= 6.35 m Wp=36KN/m WL=47.5kN/m 1.Calculate the nominal moment capacity of the beam. 2. Calculate the strain of the tension bars. 3. Calculate the strength reduction factor of the beam. Activ Go to
Situation #3: Given is a rectangular beam having the following parameters; d = 490 mm d' = 60 mm b = 300 mm fc' = 27.6 MPa fy = 276 MPa Mu = 620 kN.m %3D 10 نقاط Compute for the required steel 3.1 area in the compression side إجابتك ibäi 12 Compute for the required steel 3.2 * area in the tension side
The reinforcement steel consists of 5 bars with each having a diameter of 13.75 mm. Take pb-0.425. a) Determine the failure type of RC rectangular beam b) Calculate the ultimate moment capacity (Mr) 429.27 mm A$₁ aaaa 202.52 mm 33.50 mm C16/S420 Yme = 1.5 Yms = 1.15 Q2. The beam given in Q1 is subjected to 23.05 kN dead load distributed over the 4.72 meter span of the beam. Live load is 7.20 times the dead load. Determine if this beam can safely resist the moments created by the given loads.
A reinforced concrete beam is 250 mm wide with an effective depth of 400 mm. Use f'c= 21 MPa and fy = 275 MPa. The section is reinforced with 4 - $25mm bars. U = 1.2D + 1.6L. a. Compute for the nominal flexural strength. b. Calculate the design flexural strength of the section. c. Calculate the safe service live load moment if the service moment from total dead load is 96 kN-m. d. If the beam is 5m long with a moment from total dead load of 96 kN-m, find the maximum moving concentrated service live load that can be supported by the beam.
Refer to the figure shown. 1450 300 Given are the following: fc' = 35 MPa fpu = 1,500 MPa Aps = 1,800 mm? fpy = 1,320 MPa Use bonded tendons as prestressed reinforcement. Determine the nominal moment strength. (kN-m) 650 120
SITUATION 1 Determine (approximately) the force in each member of the truss. Assume the diagonals can support either a tensile or a compressíve force and assuming that the díagonals cannot support a compressíve force. A. Use Method 2 7 k 14 k 14 k 7 k Н F E oo 2 k 380 6 ft A D В C 8 ft 8 ft 8 ft B. Use Method 1 50 kN 40 kN 20 kN E D 3 m B 3 m 3 m
1. Illustrate the loading along BEHK subjected to service dead load of 5 KPa (including its selfweight) and service live load of 2.4 KPa. Use S = 3m and L=4m. 2. Calculate the maximum positive and negative moments using Approximate Method provided by NSCP. 3. Design the reinforcement and provide beam illustration. S S S A D G L B E H L C F L
A 90mm concrete slab is supported by a beam 7.50m clear span and 1.20m on center. Web dimension and effective depth are 300mm and 500mm respectively. If the factored moment is 730kN-m, fy=420MPA and fc'= 21MPA. Use a reduction factor of 0.90. Determine the maximum steel area in mm2. What is the balanced steel area in mm2? Determine the design strength, kN-m.
An angle bar 100x100x11 mm tension member is connected with 20-mm-diameter bolts as shown in the figure. Both legs of the angles are connected. Use F, = 248 MPa and F, = 400 MPa. 0 o o o 1. Determine the nominal strength for tensile yielding in the gross section. B. 429.67 KN D.390.10 KN A. 515.59 kN C. 545.60 kN Determine the effective net area of member. A. 1,573 mm C. 1,605 mm Determine the nominal strength for tensile rupture in the net area. A. 642 kN C. 554 kN 2. B. 1,632 mm D.1815 mm 3. B. 730 kN D.650 kN