Question 3 of 10View PoliciesCurrent Attempt in ProgressAnswer: WoAThe steel beam has the cross section shown. The beam length is L = 5.8 m, and the cross-sectional dimensions are d = 400 mm, bf = 210mm, tf = 14 mm, and tw = 7 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if theallowable bending stress is 160 MPa.A72Save for LaterWoB72CkN/m- / 10 E|||d600Attempts: 0 of 3 used Submit Answer

Given Data:Length L=5.8mCross-sectional dimensions:d=400mmbf=210mmtf=14mmtw=7mmAllowable bearing…

The steel beam has the cross section shown. The beam length is L = 5.8 m, and the cross-sectional dimensions are d = 400 mm, b = 210 mm, tf 14 mm, and tw = 7 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 160 MPa.

The steel beam has the cross section shown. The beam length is L = 5.8 m, and the cross-sectional dimensions are d = 400 mm, b = 210 mm, tf 14 mm, and tw = 7 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 160 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A W18X 97 steel beam will carry the given loads shown in Figure 1. Using ASD with A-36 steel (Fy = 250 MPa). A. If the beam is laterally supported at the two vertical supports only.a) What is the allowable bending stress in the beam in MPa?b) What is the actual bending stress developed in the beam in MPa?c) What is the actual shearing stress developed in the beam in MPa? B. If the beam is laterally supported at the two vertical supports and at its mid-span.a) What is the allowable bending stress in the beam in MPa?b) What is the allowable shearing stress in the beam in MPa?.Neglect the effect of beam weight.
A 210 kN axial compressive load is applied to a W530x101-steel column with the length of 3.20 m and cross sectional area of 12900mm2. The modulus of elasticity of this steel is 203 GPa. a) Find the stress acting on the column. b) Find the length change of the column under this load. For the toolbar, press ALT+F10 (PC) or ALT+FN+F10 (Mac). BIUS Paragraph Arial 14px A v
in 21- ő A steel beam is reinforced by three steel rods. The modulous of elasticity for concrete is 20Gpa and for steel is 200Gpa. Maximum allowable stress for concrete is 9.45Mpa and for steel is 140Mpa. Calculate the largest allowable positive WBT bending moment in the beam. иа mo maod motinu od o boblow need sved Ha bus 400mm aidT (alonnerlo ert to rigiow stongi)/4000E of Trup 200-0 signs or botuesom sWnworla es berloss M bris V zsra erli owob stiW maod sdi to mergeib insm brol bus borlism tuo sallimill nollor 10 nige over on The modulus of elasticity for concrete is 20Gpa and for the steel is 200 Gpa. Allowable stress for concrete is 9Mpa and for steel is 140Mpa. Calculate the maxium allowable bending momemt that can be applied per metal rod of the concrete slab. 150mm 200mm D=16mm 140 mm -22mm Diameter TOPABA t 50mm T 140 mm 140 mm 140 mm
AW14x22 beam is subjected to a moment of 55 ft-kips. What is the bending stress in the beam in psi? Round to the ones place. Type your answer...
6. For the beam and loading shown, calculate (a) the equation of the elastic curve for portion BC of the beam, (b) the deflection at midspan, (c) the slope at B. The beam is W200X46.1 with E-200GPa and load density of 5000N/m with L=6m P = WL 5 A y W familie B 01010 -12-1 C X
An 5355 Class 1 laterally restrained universal beam (UB) does not support a high shear load. What is its Design Bending Resistance Med? Give your answer to the nearest whole kNm. Do not include units in the answer box. Flange thickness t,-34.3 mm Plastic section modulus Wply-3,126 cm³ Plastic section modulus Wez-235 cm³
← Expert Q&A Q6. A simply-supported beam spans 10 m and is made from a 700WB150 steel section. A static vertical concentrated load of 400 KN is applied as shown in Figure. In the event of a fire, the temperature of the steel rises at a constant rate of 15 °C per minute up to a maximum of 750 °C. Assume that, at 20 °C, the steel has a yield stress of 300 MPa and Young's Modulus of 200 GPa. The ambient temperature (before the fire starts) is 20 °C. Determine whether the beam will collapse during the fire, and if so, how long after the start of fire will this occur? 6 m Self weight 400 kN 4 m
1. Calculate the critical buckling load Pcr for the rigid bar AB shown below: P L k B A C D 10 ft 30 ft 10 ft
O O O"lZAIN IQ docs.google.com/forms O 55 MPa التحديد bl 6 Determine the maximum BM occurs for the beam shown below 3 kN/m C 2m 4 m -24 kNm O -48 kNm -12 kNm - 96 kNm no one ద 13 FOR THE RIGID BEAM SHOWN BELOW FIND THE STRESS IN
10-3 Shearing Stress and Deflection in Composite Beams 423 1014. A rectangular section 150 mm wide by 250 mm deep resists a bending moment of 140 kN m. The material of the beam is noniso- tropic with the tensile modulus of elasticity twice the compressive modulus. Determine the maximum tensile and compressive stresses in Ans. 0₁ 108 MPa; oc - H 76.5 MPa the section.
A simply supported beam has a height of 600 mm and a width of 300mm. Determine the maximum safe live load that the beam can carry. The dead load is the beam weight plus a superimposed load of 15 kN/m The stirrup size is 12 mm, the top bars are 2-20 mm and the bottom bars are 5-28 mm. The clear distance between layers of bottom bars is the bar size, 28 mm. Use fc'=30 MPa, Grade 60 (fy=414 MPa) reinforcements and concrete cover of 50 mm.
Ultimate axial load