Calculate the internal axial force in member AB, BE, BF and BC and state whether it is in tension or compression by using: a- The joint method. (refer to the course similar example) b- The section method ? c- Calculate the internal axial force in member CD and CF and state whether it is in tension or compression. Follow the method of your choice. d- Calculate the stress in MPa at the bars CD and CF if their cross section areas equal respectively to 2.0 cm² and 300 mm². E 10KN 4m 4m F G 4m C 10KN 20KN 4m 8m

Calculate the internal axial force in member AB, BE, BF and BC and state whether it is in tension or compression by using: a- The joint method. (refer to the course similar example) b- The section method ? c- Calculate the internal axial force in member CD and CF and state whether it is in tension or compression. Follow the method of your choice. d- Calculate the stress in MPa at the bars CD and CF if their cross section areas equal respectively to 2.0 cm² and 300 mm². E 10KN 4m 4m F G 4m C 10KN 20KN 4m 8m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 1 Please choose the correct answer and also write down your solution. (1) The beam is subjected to the shown loading. What is the correct statement regarding the flexural stress at A and B? P P a. Both og and og are tensile stress. 0.5 m 0.5 m 0.5 m b. Both oa and og are compressive stress. Og is tensile stress and og is compressive stress. с. d. OA is compressive stress and og is tensile stress. A В (2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio of the magnitudes of the maximum tensile and compressive flexural stresses over the a-a cross section? b. 3/7 a. 7/2 d. 2/10 е. 3/10 h. 10/3 c. 7/3 f. 10/2 i. 1/1 g. 2/7 250 mm 20 mm 60 mm 200 mm 2 m 1 m 15 mm 15 mm
1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter aluminum [E = 10,000 ksi] rod. Steel [E = 30,000 ksi] tube AB has an outer diameter of 3.50" and a wall thickness of 0.216 in. Determine (a) the stresses is sections AB, BC and CD, and (b) the deflections of joints B and C. [OAB = 3.40 ksi (C), Osc = 5.863 ksi (T) Oc, = 4.959 ksi (C), 8, = 0,0054"– , d. = 0,02975"→] %3D %3D %3D %3D 13 kips 17 kips A C 13 kips 17 kips 4 ft 5 ft 5 ft
Physics The following truss is subjected to a load of P = 31 kN at joint C. The pin at joint A has a diameter of 25 mm and is subjected to double shear. Determine the average shear stress developed in pin A of the truss. Im PRN Im Pin A a. In your Hard Copy, draw a FBD of the truss. b. What is the Resultant force at A? Aresultant = Number Units (Answer to 3 sig digs) c. What is the shear stress in A? TA = Number Units (Answer to 3 sig digs
The beam is loaded by two point forces P. The beam is assembled according to the cross-sectional view by nailing wooden parts with cross-sections of 50 mm x c = 220 mm and 25 mm x d = 260 mm. How large can the value of the load P be when the distance between the nails in the longitudinal direction of the beam is 100 mm, the cross-sectional area of the nail is 9 mm2 and their permissible shear stress is 110MPa? Then calculate the maximum stresses and shear stresses of the beam at that load when the distance between the articulated supports is L = 1.9 m and the length of the beam projections a = 1.3 m. Permissible shear force of one nail? kN Static torque of the cutting surface? mm^3 Maximum torque change in cantilever? kNm Cutting force of the projection? kN Magnitude of force P? kN Calculated with the obtained force P maximum normal stress? MPa shear stress maximum? MPa
*4-88. If the allowable normal stress for the bar is O allow = 120 MPa, determine the maximum axial force P that can be applied to the bar. %3D 5 mm 40 mm 20 mm P- r = 10 mm 20 mm
Determine the maximum magnitude of load P that can be applied to the truss. The maximum allowable tensile force in the members of the truss is (Ft) max = 5.2 kN, and the maximum allowable compressive force is (Fe) max = 3 kN. Take d = 2 m. (Figure 1) Figure 1 of 1 E d/2 C PV d/2 <
Determine the normal stress in members BD, AC, and BC in the truss shown. The crosssectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value
ANSWER IN FOUR DECIMAL PLACES. For the truss shown, determine the normal stress of member AE, FB and CD. Identify if the stress is compression or tension. A = 1200 mm2.
! Required information Consider the given state of stress. A 16 ksi 10 ksi Determine the normal and shearing stresses after the element shown has been rotated through 15° clockwise, using Mohr's circle. The normal stress Ox'is - |ksi and Oy'is ksi. The shearing stress Tx'y'is ksi.
2. Determine the normal stress in members DF, GH, and GI in the truss shown. The cross- sectional area of each member is 900 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 5 kN A 2 kN B 3 kN C F H K 2 m 2m 2 m
The bar ABC is fixed at A and restricted at C by two 16-mm diameter vertical steel bars, 1500 mm long. A 6000 Nm torque is applied at B. Steel has a modulus of elasticity of 200x109 N/m2 and a shear modulus of 80x109 N/m2. Determine: Maximum shear stress at the horizontal bar ABC Tensile Stress at bar MN Note: Draw the Free Body Diagram, Compute for all of the necessary elements, Include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
8 kN 4 m 15 kN 5 kN 2 m 2 kN 2 m 2 m A B с D E The aluminum rod shown has a diameter of 20 mm and is subject to axial forces acting at A, B, C, and D. Assume the rod has a Young's modulus of E = 70 GPa. a) State the internal axial forces within sections AB, BC, CD, and DE. Remember to indicate whether they are in tension or compression b) What is the displacement of A relative to C? c) What is the displacement of A relative to E?