Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal assembly. Each traffic signal has a mass of 44 kg, while the masses of members OC and AC are 56 kg and 50 kg, respectively. Positive answers are to the right, up, and counterclockwise. A 44 kg Answers: Mo-i 6.4 m 44 kg B G 1.0 m 2 KN KN kN-m 50 kg 5.4 m 56 kg 6.5 m

Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal assembly. Each traffic signal has a mass of 44 kg, while the masses of members OC and AC are 56 kg and 50 kg, respectively. Positive answers are to the right, up, and counterclockwise. A 44 kg Answers: Mo-i 6.4 m 44 kg B G 1.0 m 2 KN KN kN-m 50 kg 5.4 m 56 kg 6.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. (a). Obtain the total elongation of a steel bar of cross-sectional Area 1250mm2 acted upon by forces indicated in the diagram below. E-205,000N/mm2 15N- 5N 20N 40N 15N 1.5m 1.5m 3m Im TAt man Im 12. 5omx
Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal assembly. Each traffic signal has a mass of 40 kg, while the masses of members OC and AC are 60 kg and 51 kg, respectively. Positive answers are to the right, up, and counterclockwise. 40 kg Answers: Ox= i Oy= Mo= i 5.9 m 40 kg B G 1.0 m KN kN kN.m 51 kg 4.9 m 60 kg C 7.3 m 0
PROBLEM 2 This force-couple system is to be replaced by an equivalent system consisting of the following: a couple moment Mx, and a single force, Rc acting at C. Draw the diagram for the equivalent system and determine Mx and Rc. В A 100N 80N Thislis not your 110N-m 50N 150N do not use ir in tradoraeto 50N were your Wn. 130 N D C 180N-m 12° 30N this is hor voter own property so da not use i any way as if it wele Tour own. 1m
6 Which of the following gives the reaction at C in the given beam? 300N 210 N/m A 100 Nm TITT 5m B O 1238.5 N 1693.5 N 1700.0 N O 1771.5 N int. hinge D 5m CT 3m 12m 2m+ 120 N/m ETT 3m F
Deflection of Beams Use Conjugate Beam Method Given: X - 274 у-74 а-8 b - 4 C- 9 Y kN/m 10 m 9. What is the reaction at A? (kN) 10. What is the deflection at a point 2 m from A? (N/m³)/EI 11. What is the deflection at a point 2 m from B? (N/m³)/EI 12. What is the slope at a point 2 m from A? (N/m²)/EI 13. What is the slope at a point 2 m from B? (N/m²)/EI 14. At what distance from A will the maximum deflection of the beam occur? (m) 15. What is the maximum deflection on the beam? (N/m³)/EI
3. Find the value of Ely at the position midway between the supports and at the overhanging end for the beam shown and also determine the location of maximum deflection. 400N/m boON 1m 3m 2m 2m Det the mid support deflectuon + the deflection if E = 200 G Pa M2 HWT I: 1350 x 10° mm4 12:00 T0on - FRI 12 noom 5ON 100 N /m b) EI 8 mid span = ? El 8 over hang
Homeworks: A steel shaft of two segments AB and BC which are rigidly fastened at B Determine: 1) Reactions at A and C. 2) Maximum angle of rotation. 1000N. mn/mm 4m 100mm S0mm 5mm
Appendix A, Problem A/048 Determine the moments of inertia of the Z-section about its centroidal xo- and yo-axes. 24 mm Answers: Ixo 145 mm Iyo 11 11 = 120 mm Yo 24 mm 120 mm 24 mm (106) mm4 (106) mm4
Q2: Four people are attempting to move a stage plat- form across the floor. If they exert the horisontal forces shown, determine (a) the equivalent force- couple system at O and (b) the points on the x and y-axna through which the line of action of the single resultant foroe R passes. 20 N 300 N- 1680 mm 320 N 200 mm 140 N
Replace the two forces which act on the pneumatic-hose reel by an equivalent force-couple system at O. The 20-N force which results from the weight of excess hose being wound up lies in the plan parallel to the y-z plane and loses contact with the hose reel at a radius of 160 mm. 350. 110 130 30 130 N B 75 30° 15° 20° 20 N Dimensions in millimeters
Determine the value of 6A2b2/L2 to be used in your 3 Moment Equation for Continuous Beams. 200 lb/ft а. -1250 b. 36667 C. 3750 d. 13333 10 ft 10 ft R1 R2 R3
In Figure 11, three forces are applied to a triangular plastic board. The board is pinned at Point A. Determine the magnitude of the moment and the direction of the rotation of the board. F1 is applied at the midpoint of the hypotenuse. RESULTANT NO 1 2 3 FORCE THETA Fy U/D 500 100 300 Fx R/L 33.13 -273.27 D 418.72 R 73 -95.63 D -29.24 L -154.51 L 59 257.15 U Ry= -111.75 Rx = 234.97 R = 260.19 KN 0 25.44 DEG DIR: DOWNWARD TO THE RIGHT Moment +440.82 KN-m Direction: Clockwise F1 = 500 KN 70° 100 KN = F2 A 4.00 all dimensions are in "meters" 73° 3.00 59° F3 = 300 KN