The load on a 120V, 60 Hz supply is 5 kW (resistive), 8 kVAR (inductive), and 2 kVAR (capacitive).Calculate the following Calculate the current power factorpf =lagging, leading, or unityCalculate the total current before power factor correctionTbefore=unitsIf its desired for the power factor to be improved to 0.90 lagging, how much capcitive reactive power needs to be supplied to the network?Qneed=unitsCalculate the total current after power factor correctionunitsTafter

Asked to find the following,Note: “Since you have posted question with multiple sub parts, we will…

Calculate the current power factor pf= lagging, leading, or unity Calculate the total current before power factor correction ITbefore = units If its desired for the power factor to be improved to 0.90 lagging, how much capcitive reactive power needs to be supplied to the network? Qneed= units Calculate the total current after power factor correction Tatter units

Calculate the current power factor pf= lagging, leading, or unity Calculate the total current before power factor correction ITbefore = units If its desired for the power factor to be improved to 0.90 lagging, how much capcitive reactive power needs to be supplied to the network? Qneed= units Calculate the total current after power factor correction Tatter units

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Which one of the following statements is true: The purpose of the power-factor correction is to add inductive elements to keep real power at a minimum level. The purpose of the power-factor correction is to add resistive elements (typically resistances) to improve the total reactive power. The purpose of the power-factor correction is to add reactive components (typically capacitive) to establish a system power factor closer to unity. The purpose of the power-factor correction is to add resistive elements (typically resistances) to establish a system power factor closer to zero.
Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
For maximum average power transfer in the circuit shown in the figure, set the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
A 3500 ?? load with a power factor of 0.70 leading is fed from a source at 50 ?? with an RMS voltage of 230 ?. A) Determine the load (type and value) to be installed in parallel to correct the power factor to 0.9 lagging. Indicate which is the apparent power value after correction and draw the corresponding power diagrams B) Determine the load (type and value) to be installed in parallel to correct the power factor to 0.9 leading. Draw the corresponding power diagrams.
Find the complex power and power factor for the indicated element(s).( need only handwritten solution .otherwise downvote.)
1. Write down a formula for the three-phase power factor, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements. 2. Write down a formula that relates three-phase apparent power to active and reactive power. 3. Draw a graph that depict single-phase waveforms for a purely sinusoidal 50 Hz voltage and a lagging current.
Calculate the rms values of load voltage and current for the circuit shown below. Please show work
One side of a transformer has What is the voltage (in V rms) at the secondary? 1,800 turns while the other side has 450 turns. The high voltage side is connected to a 240 Vrms source. The low What is the current (in A rms) at the secondary? What is the current (in A rms) out of the source? What is the value of the load impedance when referred to the primary? • Referred impedance = voltage side (secondary) is connected to an impedance ZL = 20 + j10 Q. Provide at least 4 digits after the decimal point. +j_ N What is the value of the source voltage (in V rms) when referred to the secondary?
Discuss the concept of reactive power and its role in grid stability.
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
Two impedances Z₁ and Z2 are connected in series to a voltage source with voltage Vs volts. Let V₁ be the voltage across Z₁ and V₂ be the voltage across Z2. Then, the total voltage Vs is divided between V₁ and V2 in proportion to impedance values Z₁ and Z2. O a. True O b. False