B) What is the difference between Spaced Sheeting and Close Sheeting

Q: Question Bank - Centroids Using the method of composite curves, locate the centroids of the plane…

A:

Q: What is the relationship between sensitivity and radius?

A: The change in angle or gradient of the level that results in movement of the bubble is known as…

Q: What is the other name for air/cloth ratio?

A: The air to cloth ratio is defined as the total amount of air that is flowing through the filter of…

Q: 46. Which defect occurs if a paint is applied excessively thick?

A: Which defect occurs a paint is applied excessively thick

Q: Typical components of a green roof system include the following details.

A: Answer Green Roof System The Green roofing system fulfills the basic roofing requirement. The green…

Q: Determine external indeterminacy

A: Given data : Number of external support reaction (R)=3+1+2=6

Q: Just draw the figure, if possible

A: Given data in question  Forward bearing  Back bearing Line Closed traverse To find out  Draw diagram…

Q: Where exactly in these designs is there a lack of coherence, and what types of things might be done…

A: Coherence describes the properties of the interrelation between physical quantities of a single wave…

Q: Beam Colume

A:

Q: II. Locate the centroid of the composite area below. Y 50 mm 80 mm R=50mm 250mm R=65mm -- X 50 50 mm…

A: To find centroid of composite area

Q: What are the classes of hardboard?

A: Hardboard has high density and high strength, which is a quality substitute for wood and is commonly…

Q: Define the parts presented in the image

A: Underlying structure parts are particular primary structure items planned, designed and produced…

Q: Show me this drawing Step by step how to draw it. thank you 25 105 30 ø16 60° 40 60 70 it's from…

A: To Determine Steps to be used in drawing the given figure in CADD software.

Q: How are one- and two-point perspective different, and how can the difference be seen in an…

A:

Q: What is Sloped Glazed.

A: Glazing: The installation of glass to the building components or interiors of the structure is…

Q: What is typical grade stamps for structural panels.

A: Grade Stamping is done for structural panels in order to differentiate and manage the panels in a…

Q: 8. The general plane of the construction drawing with background and color is more intuitive and…

A: 8.True   9.True     10.True

Q: Using Centroid by Composite Shapes, determine the x- and y-coordinates of the centroid of the shaded…

A: To find centroid of shaded area

Q: When drawing a plan in AutoCAD, the user will draw the actual dimension of the building. True False

A: When drawing a plan in AutoCAD, the actual dimension of buildings are not drawn but their scaled…

Q: Explain isobar?

A: An isobar is a contour or curve showing all the points below the earth's surface having equal…

Q: What are the Automated 3D truss/steel structure on-site assembly

A: Concept- On-site assembly- The management and completion of all project operations used to deliver…

Q: 30 10 30 10 15 20 15 10

A: Line command of autocad is used  We can use either absolute coordinate method or relative coordinate…

Q: structure clash and boundary clash

A: structure clash and boundary clash

Q: What are the different types of streaking?

A:

Q: llustrate a simple work plan drawing of a bridge.

A: Bridge is a concrete( some parts are of steel) structure that can carry a road, railways across an…

Q: Using Centroid by Composite Shapes, determine the x- and y-coordinates of the centroid of the shaded…

A:

Q: Dimension of the interior ceiling is 9.00m x 2.00m. How many pieces of plywood is ecessary to cover…

A: To find number of plywood required to cover ceiling

Q: Sketch and explain the working principle, constructional details, limitations and factors…

A:

Q: The web thickness of lightest WT shape is?

A: As per the AISC steel construction manual  The web thickness of lightest WT shape is  =  1/10 inch…

Q: Using Centroid by Composite Shapes, determine the x- and y-coordinates of the centroid of the shaded…

A:

Q: ri= 72 mm x r2 = 120 mm

A:

Q: m, hw= 440 mm, bw = 420 mm ds= 10 mm, ct= 30 mm, cb = 35 mm. Steel bar details: compression side m…

A:

Q: what is the distinction between primary textures and secondary textures?

A: Difference between primary and secondary texture are as follows: The primary texture happens before…

Q: Draw half sectional Front View and Top View of the following component

A: The three dimensional projection is the isometric view and the 2 dimensional projection is the…

Q: Discuss Connections with Walls

A: A wall is just a framework and an outer layer that describes a region, conveys a load, improves…

Q: 1. What is the surface texture in microinches is specified for the cylinder surface with a maximum…

A: 1) The surface texture in micro inches is specified for the cylinder surface with a maximum material…

Q: Explain the meaning of the term "striping."

A: The term striping refers to a distress in flexible pavement Which is distinguished by the loss of…

Q: Detail drawing is a multiview representation of a single part with dimensions and notes. Select one:…

A: Detail drawing conveys the information and instructions for manufacturing the part. Hence Detail…

Q: Illustrate various architectural features of Mahabat Khan Mosque, Peshawar.

A: Mahabat Khan Mosque was built during the Mughal period in the 17th century.

Q: Classification of lines in details

A: Answer:-  Line:- A line is a one dimensional figure, which has length but no width. A line is made…

Q: 1. what are methods used for representing points in AutoCAD? 2. What are the differences between…

A: 1. Methods for Points Representation: Absolute Method - The points are represented by exact…

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.