B) Answer by True or False for the following statements: 1-Paint shops have extra hazard. 2-The nozzle of hose reels of firefighting system of buildings must reach a height of 10 m. 3-Gutters are usually used with horizontal surfaces. 4-The direct method of water supply of buildings is usually reduced the water pressure of the adjacent buildings. 5-Surface water doesn't get easily pollution.

B) Answer by True or False for the following statements: 1-Paint shops have extra hazard. 2-The nozzle of hose reels of firefighting system of buildings must reach a height of 10 m. 3-Gutters are usually used with horizontal surfaces. 4-The direct method of water supply of buildings is usually reduced the water pressure of the adjacent buildings. 5-Surface water doesn't get easily pollution.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Coming home after the end of the winter semester, you find that your family’s swimming pool has not be maintained well. In particular, it has no chlorine residual at all, and it is full of tree leaves. You buy a concentrated chlorine solution (1% as Cl2) and begin to meter it into the pool at a rate of 100 mL/hour. The pool has a volume of 200 m3. You also add new water, and remove in-pool water, at a rate of 3.785 L/minute. The chlorine reacts with the organic matter in the with a rate of 0.5/hour. How long will it take to get the Cl2 residual up to 1 mg/L if you add Cl2 continously.
Question - There is a small spill of a toxic material on a paved surface of a chemical plant. This spill has width 0.8 ft and a length of 2.5 ft. The wind is a 10 miles per hour in the direction parallel to the length of the spill. Estimate the rate of evaporation in grams per hour. There is no toxin in the air at time 0 and at infinite distance from the spill. Assume air to behave as an ideal gas. Assume the toxic material can be considered an ideal solution with psat = 22 mmHg. MWtoxin = 164.4 g/mol, Ptoxin =1.69 g/cm³, Pair = .001225 g/cm³, Hair= 0.0187 CP, MWair = 28.9 g/mol, Dtoxin,air = 0.0888 cm²/s.
5 4 Choose the correct letter, A, B, C or D. Estimate the number of filters required for water treatment if the flow rate=1.4 m/s, the design loading rate to the filter is 200 m³/d.m², and the surface area of each filter= 80 m². One of the following media has the lowest specific gravity in the filter body: What is representing the total alkalinity of water sample, if the pH of water <=10.33 In the sedimentation tank, the over flow velocity depends on: What is the tip speed of an impeller in slow-mixing tank that has a diameter of 1.1 m and rotational speed of 0.6 rps? A 7 Garnet HCOS The flow rate 1.06 m/s B 10 Anthracite CO The surface area of the tank 2.39 m/s C 5 Sand D 12 2.07 m/s Gravel H₂CO3 A+B The detention A+B time 1.54 m/s
5. You are asked to design a single media filtration system for a drinking water facility. The design flow rate is 20 mgd (million gallons per day). The ideal filter velocity for your system is 8 m/hr. You design a set of filters to be used in parallel. Each filter box has a surface area of 50 m². a. How many filters do you need to construct? b. Estimate the (clean-filter) head loss in kPa? c. What mass removal (filter efficiency) would you expect for an influent stream that contains equal parts (by mass) of 1, 10 and 100 um particles? You can assume an adhesion efficiency a = 0.7. Sand Effective Size (mm) 0.8 Uniformity Coefficient 1.2 Grain Porosity Density (g/cm³) 2.6 0.4 Layer Thickness (m) 1.5
Calculate dimensions and power requirements for Flocculator to treat 30000 m3/d wastewater flow. Flocculator should be 4 m deep and maximum 10 m wide.Use following information:μ = 1.003*10-3 Ns/m2 ρ = 999.1 kg/ m3 CD = 1.8 G*t = 3.5*104 Vp = 0.67 m/s 4paddle,4board configurations
1.Determine how much water is required to dilute 20 liters of a solution that is 15% dye so that a 5% dye solution is obtained. 2. 2. A pipe can fill a swimming pool in 15 hrs. If a second pipe is open, the two pipes together can fill the pool in 5 hrs. How long would it take the second pipe alone to fill the pool?
Contaminant X is detected in a drink- ing water supply (4000 m³/day), and 94.99 percent of contaminant X must be re- moved to comply with federal water quality standards. If contaminant X has a "dimen- sionless" Henry's law constant, H, value of 0.25, then what is the design air-to-water flow ratio for an air stripping packed tower, assum- ing 3.5 times the minimum?
You have 4 acre of watermelons that you irrigate. The irrigation system you use under standard pressure of 35 psi has a flow rate of 105 gpm. The nozzle sprays a circular area with a radius of 24 feet. a. How many square feet are in the water- melon patch? b. What is the area covered by one nozzle? c. How many nozzles are needed? d. What is the flow rate when all the nozzles are used?
Situation 2: Water drops from a fáucet at the rate of 5 drops per second. h2 hi
As the project engineer for your consulting firm, you are in charge of designing a flocculation tank to treat municipal drinking water. The design flow for the plant is 0.050 m3/s. The average water temperature is 10oC. The following design assumptions for the flocculation basin have been made:Number of tanks = 1Number of compartments in tank: 3Tapered G in 3 compartments: 60, 50, and 20 s-1Detention time = 30 min for entire flocculation basinDepth = 3 mTanks will have a square compartment plan (overhead) view1 Horizontal shaft paddle wheel per axis will be usedPaddle wheels will have 4 arms and 2 blades/armPaddle blades are 3 m long by 0.6 m wide. Assume blade spacing (diameter) of 1 and 2 m. Design the flocculation tank by providing the following for the first two compartments only:a) Tank and compartment dimensions in mb) Water power input in kWc) Rotational speed of the paddle wheel shaft in rpm
Q#5. a) Explain the term “Atmospheric pressure”. b) Explain the basic components of air pollution problem Subject: environmental engineering ii
a) Draw a neat sketch of a Trickling Filter unit and discuss how it can remove impurity from wastewater.