Answered: aterial S-400 N/mm² and E21000

Engineering

Mechanical Engineering

aterial S-400 N/mm² and E21000

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.9P: A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in....

See similar textbooks

Related questions

Q: Figure Q2 shows a rigid link supported by a pin at C and two A-36 steel wires. Each wire having an…

Q: Two plates of which (2.5 d) and d as outer and inner diameter respectively and thickness 25 mm each…

Q: N / acting on the structure in Fig. (4) is the horizontal force NKA at the end D. Find the effect of…

Q: H.W 1 The bracket plate is 40 mm thick. b= 272 mm. Load on the bracket, P= 100 kN; spacing, C (…

A: 1. Draw a diagram for the given cross-section. Here, A, B, C, D, E, F indicate the shown rivets, Fp…

Q: Assume the plate shown in Figure has negligible weight. There is a ball and socket joint at A and a…

Q: The assembly is the same as in problem 2. It consists D of two rods AC and BD attached to the 100-lb…

Q: The AB bond must be made of a steel for which the normal stress limit is 450 MPa. Determine the…

Q: the expected answer is for I(1)= 1.43mm snd 12= 2.86mm LLLL LULU 2 -1²/₂- w A rod of negligible mass…

A: To find: The extension in each spring. Given: The weight of load is W=5 N. The spring constant of…

Q: Khowing ) for all surfaces of contacts determ magnitude of the force P required to move the (10 kg)…

A: given:mass of small block m1=10kgmass of big block m2=20kgμ=0.2

Q: 6. Three wires are used to support the 150-lb force. The wires AB and AC are made of steel, and wire…

A: Tension occurred in a cable due to stretch or pulled It is an internal force that acts all along the…

Q: Problem: Using the method of joints, find all forces on each member and indicate if tension or…

Q: A tensile load of 40 kN is acting on a rod of diameter 40 mm and of length 4 m. A bore of diameter…

A: Given: Tensile load P=40 KN Diameter of the rod D=40 mm Area of the road A=π4D2…

Q: For two plates 1 and 2 a riveted system is suggested to connect them. W thickness of plate. 1 is 12…

Q: The bridge construction company Z is facing problems with the mechanism of the crane, which it uses…

Q: how many times is the system

A: For solution refer below images.

Q: The assembly is the same as in problem 2. It consists D of two rods AC and BD attached to the 100-lb…

Q: The 1.5 kN vertical OA pole is supported as shown in the figure and loaded with a horizontal force…

A: Given: The weight of the pole is 1.5 kN. The pole with the supported load is shown below:

Q: A 200-mm lever AB and a 240-mm-diameter pulley are welded to the axle BE, which is supported by…

Q: SAMPLE PROBLEM 2: Assume that AE are equal for each rod Reqd: Internal forces for member AB, CD, EF…

A: Given Data: Length of the beam, L=0.8 m

Q: A uniform, 6.0 m, 1150 kg beam is hinged to a wall and supported by a thin cable attached 2.0 m from…

Q: 1: Pin B can support a load up to 8 kN, roller A can support a load up to 4 kN. Calculate the…

A: ∑MB=04×2×w-NAsin 30°×3sin 30°-NAcos 30°3cos 30°+4=0NA=1.23w∑Fx=0NAsin 30°=BxBx=0.61w∑Fy=0 By+NAcos…

Q: Q3. For two plates 1 and 2 a riveted system is suggested to connect them. Where the thickness of…

A: Given Data The diameter of the rivet is: d=10 mm The pitch of the rivet is: p=50 mm For the plate 1…

Q: | 30/ 20 kN + 200 mm E F $ 200 mm 135° 45° 45° B

A: The force which is offered by the foundation to a block placed over it is termed as reaction force.…

Q: A load that weighs 165kg and has an end to end length of 1.2m has to be lifted by a crane. We have…

Q: An A-992 steel wire is connected at ends B and C With an initial diameter of 15 mm. The weight of…

Q: A safety valve spring having 9 and V2 coils has the ends squared and ground. The outside diameter of…

A: Please find the solution below

Q: Q2: The horizontal force NK 5 at the end D is acting on the structure in Figure (2). Find the effect…

Q: The space truss above is supported by ball-and-socket joint at points A, B, and E. A single force F…

Q: Assuming the pulley system below is weightless and frictionless pulley (see below), if the load of…

A: Solution:

Q: rmine the force in membe for the truss loaded and supported a shown in figure (3). Does the…

Q: A load of F of 3 kN is applied to the pulley shown in the figure. Plate 1 is attached to two plates…

Q: A pin in a knuckle joint carrying a tensile load Fdeflects somewhat on account of this loading,…

Q: For the arrangement shown in figure, find the force F needed to cause impending motion F to 3kN…

Q: Problem 2: A circular rod tapers in diameter from 50 mm from one end to 20 mmon theother end for a…

Q: A bolt of major diameter 12mm is required to clamp 2 steel plates. Cross sectional area of the…

Q: Calculate the internal member force of BC using method of joint and state if the member is in…

A: From the given figure let the reaction force at A and B as RA , RB acting in vertical direction.…

Q: For the arrangement shown in figure, find the force F needed to cause impending motion F to 3kN…

Q: 600 N 4 m 900 N 4 m B 6 m Calculate the force in each truss member using the method of joints, and…

A: Data given-

Q: 1. Determine the maximum weight of A that will permit the 400 lh block B to slide without tipping…

A: 1: Given: The weight of block B, WB = 400 lb The weight of the wheel, W = 644 lb The radius of…

Q: QI) A man is pulling a spring of stiffness coefficient 8 Ib/in by his hand with the entire arm held…

A: Draw a labeled free-body diagram of the given system. Calculate the force due to spring, Fs=k×x=8…

Q: A load of W=5 kN is attached to end B of arm AB with the help of a wire wound on a frictionless…

Q: The bell-crank mechanism shown below is supported by a single-shear pin connection at B and a roller…

A: Find the maximum load

Q: The bars AB, AC, and AD are pinned together as shown in the Horizontal movement of the pin at A is…

Q: oad of 12 kN is raised by means of a screw jack. The mean diameter of the square threaded screw is…

A: Given: Load to be raise, W=12 KN Mean diameter,Dm=48 mm Pitch, P=12 mm Force applied, F=180 N μ=0.12

Q: Shear strength value τ = 200 MPa The plate connection made with bolts is given in the figure. P =…

A: Given data: Shear strength (τ) = 200 MPa P = 70kN Need to determine the minimum bolt diameter.

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

Two plates of which (2.5 d) and d as outer and inner diameter respectively and thickness 25 mm each are held together by means of a bolt. The bolt material S-400 N/mm² and E210000 N/mm² while plate material E= 72000 N/mm². The initial preload in the bold is 6.0 KN and force on the joint is 12 kN. Find out size of bolt assuming factor of safety 2.0.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in. passes through each davit and supports two pulleys. are on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a =15° with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that can be carried in the lifeboat?
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
find the tensile of the bolt with diameter 38mm,80kN
The length AB for the lug wrench shown below is 12 inches. What is the maximum force (F) that one can apply on the handles without yielding the material (Steel: Sy = 45 ksi). The diameter of the wrench is 0.625 inch. (Do not make any mistakes)
An M 14 x 2 hex-head bolt with a nut and a 14R washer under each of bolt head and the nut is used to clamp together two 18-mm steel plates. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the bolt stiffness. The bolt stiffness kb is 592.69 MN/m.
Agui - 4550/2 =2276 two plates each with thickness t - 16 mm are bolted together with 6-222 mndia. bolts firming alap Joint Bolt spacing are follows St- $40mm S2 - 80mm, S3=150mm effective bolt hole dia. is 25mm A36 is used. Compute the allowable tensile Strength P t = 16 mm &t 52 747₁ 0 O O 40 60 80 40 +=16mm S-400 $3-100 S2-40 7 @ 4umm P
Find the Axial Forces in members 1 - 5. Find the Displacement Displacement of joint A (mm, positive right and up) for both Horizontal and Vertical
Two plates are clamped by a 3/4-10 UNC SAE Grade 5 bolt and regular nut with a 3/4-W plain washer as shown in figure. Top plate is made of grey cast iron and bottom plate is steel. An axial force of 12kN is acted upon the joint. Round off the length of the bolt to nearest 1/4in. Assume bolts are preloaded to 75% of proof load. 1. Determine the bolt stiffness kb. 2. Determine the member stiffness km. 3. Determine the yielding factor of safety of the bolt. 4. Determine the load factor for the bolt. 5. Determine the load factor guarding against joint separation. 1.25 in 1.00 in
A leafs spring contains 4 full-length and 8 graduated leafs. The eyebolts at the support are 20 inches apart and the system should carry a load of 400 lbs. If the thickness of the available bronze plate is 1“ and Sy = 80 ksi, what leaf width is required at FOS = 8?
The figure gives the cross-section of a grade 25 cast-iron pressure vessel. A total of N bolts are to be used to resist a separating force of 150 kN. (a) Determine kb, km, and C. (b) Find the number of bolts required for a load factor of 2 where the bolts may be reused when the joint is taken apart. (c) With the number of bolts obtained in part (b), determine the realized load factor for overload, the yielding factor of safety, and the load factor for joint separation. Use (SI) units as it applies
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
For the joint shown below, an SAE Grade 5 7/8-9 screw connects two plates. The joint stiffness constant (C) has already been calculated to be 0.2012. The pre-load (F;) in the screw is 34500 lb. If an external axial load (P) of 6300 lb is applied to the connection, what is the magnitude of the (compressive) load in the material (in units of kip)? P P red 29.4673 (with margin: 0.5893) wers