At time = 0, a constant heating power of 100 kW is applied to a boiler that intends to raise the temperature of the fluid inside to 100 °C. The initial temperature of the fluid is 25 °C. Temperature is taken every 2 minutes, starting at t = 0. The log after 1 hour is shown below. The x-axis is time (in minutes) while the y-axis is the temperature T. The system may be assumed to be of first order. 110.00 100.00 90.00 80.00 70.00 60.00 50.00 40.00 30.00 20.00

At time = 0, a constant heating power of 100 kW is applied to a boiler that intends to raise the temperature of the fluid inside to 100 °C. The initial temperature of the fluid is 25 °C. Temperature is taken every 2 minutes, starting at t = 0. The log after 1 hour is shown below. The x-axis is time (in minutes) while the y-axis is the temperature T. The system may be assumed to be of first order. 110.00 100.00 90.00 80.00 70.00 60.00 50.00 40.00 30.00 20.00

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

QUESTION 11 An inductor is connected in parallel with a 6540 resistor and a function generator. The applied voltage is 42V RMS and the total current is 67mA RMS. Find the magnitude of the current through the inductor. Enter your answer in the space provided. Round your answer to one decimal place. Your answer should be in mA but do not enter the unit.
a. What is the instantaneous current when switch is closed at t=0 b. After t=0.3s, what is the current?
Electrical Engineering Question 1 Is the FSM a Mealy or Moore machine? Choose '0' for Mealy and '1'for Moore. Reset So 0100 Format: 0/000 X/Y,Y;Y, 1/000 0/010 1/010 1/001 Answer : • Do not enter space before and after the answer • Do not press Enter after the answer
The Value of R1 is 39.4Ohms. explain
A wind turbine gives maximum output power of 1MW at a wind speed of 15m/s. Choose the correct statement for this wind turbine. a. The input wind power is 2.5MW b. The input wind power is 1.69MW c. The input wind power is 1.25MW d. The input wind power is 2.1MW
Exercise: What will be the o/p of the following meters? F.W.R H.W.R D'Arsonval Dynamo. meter PMMC PMMC meter meter meter E=10V 1) 2) 3
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
There is 50 mA of current through a coil with 250 turns. The flux is 150 µWb. What is the mmf? What is the reluctance of the circuit? A. Fm = 1.25 At - R=4.3x10-3 At/Wb B. Fm = 2.25 At - R=8.3x10-3 At/Wb C. Fm = 1.25 At - R=8.3x10-3 At/Wb D. Fm = 1.25 At - R=8.3x10-2 At/Wb
An electron synchrotron of 6 x 109eV, electrons march through the machine in a roughly circular path 240 meters long. It is normal to have around 1011 electrons circulating in this path during an acceleration cycle. The speed of electrons is practically that of light. What is the current?
With the aid of diagrams, discuss the procedure to detect zero error and cyclic error in fieldwork.
0.1 Give a short answer for only Six of the following 1. Explain the construction of turbine meter and mention for what we use it. 2. Mention the Applications of Pyroelectric sensors. 3. Explain briefly Hall effect sensor's application by measuring the fluid level in a container. 4. Explain how could we use potentiometer to measure linear displacement and angular displacement. 5. According to electrical circuits and electric fundamentals what's the evident difference between Eddy current proximity sensor and Inductive proximity sensor? 6. What's the purpose of putting an inner track with only one hole in optical sensor? 7. What's the reason behind using Wheatstone bridge with strain gauge sensor?
sistance of the resistor is 100 Ohm. urce is 100 W. what is the rms voltao