At a certain point in a pipe, air flows steadily with a velocity of 150 m/s and has a static pressure of 50 kPa and a static temperature of 4°C. The flow is adiabatic and frictionless. Calculate the maximum possible reduction in area and the following quantities for that minimum area: stagnation pressure, stagnation temperature, static pressure, static temperature, velocity, and Mach number. maximum reduction= % Po2 = To= T₂ = V₂ = kPa K kPa K m/s

At a certain point in a pipe, air flows steadily with a velocity of 150 m/s and has a static pressure of 50 kPa and a static temperature of 4°C. The flow is adiabatic and frictionless. Calculate the maximum possible reduction in area and the following quantities for that minimum area: stagnation pressure, stagnation temperature, static pressure, static temperature, velocity, and Mach number. maximum reduction= % Po2 = To= T₂ = V₂ = kPa K kPa K m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Gas flowing through a diverging nozzle has at inlet section a temperature of 20 °C, pressure 120 kN/m? and velocity 300 m/s. At the outlet of the nozzle the velocity has fallen to 100 m/s. Assuming an adiabatic flow, what is the values of outlet pressure, temperature, internal energy and specific enthalpy at outlet section. Take y = 1.333 and Cv= 0.86 kJ/kg K.
Air flows steadily at a pressure of 105 kPa at a speed of 0.1m / s and a temperature of 300K in a duct with a diameter of 10 cm. After a deformation in the duct, the flow is uniformly out of the gap with dimensions of 3cm × 6cm out of the possible state. Act like a complete gas, you can make R = 287J / kg.k Assuming an incompressible flow, calculate the velocity of air out of the gap.
In a wind tunnel air enters with a velocity of 200kmph. The static pressure and temperature of the air at the inlet of the tunnel is 110kPa and 27°C respectively. Determine Mach number, stagnation temperature, stagnation pressure and the stagnation density on a test model installed in the wind tunnel. The size of the tunnel is given as 1m x1m square cross-section. Determine the mass flow rate of the air. For air assume R=287J/kgK ; γ=1.4.
The Mach number of air flowing in a constant area duct has increased from 2 to 6 because of friction. Calculate the pressure and velocity at the exit of the pipe, if the pressure and temperature at the inlet of the pipe are p=0.14 MPa and T=21 °C.
Air enters a rectangular duct at T1 = 285 K, P1 = 390 kPa, and Ma1 = 2. Heat is transferred to the air in the amount of 55 kJ/kg as it flows through the duct. Disregarding frictional losses, determine the temperature and Mach number at the duct exit.
Carbon dioxide flows steadily through a varying cross- sectional-area duct such as a nozzle at a mass flow rate of 3 kg/s. The carbon dioxide enters the duct at a pressure of 1400 kPa and 200°C with a low velocity, and it expands in the nozzle to a pressure of 200 kPa. The duct is designed so that the flow can be approximated as isentropic. Determine the following parameters at each location along the duct that corresponds to a pressure drop of 200 kPa: (i) density; (ii) velocity: (iii) flow area; (iv) mach number. You may assume: • Carbon dioxide is an ideal gas with constant specific heats at room temperature; • Flow through the duct is steady, one-dimensional and isentropic. Use c, 0 846 kJ/kgk andk = 1.289 throughout the calculations, which are the constant-pressure specific heat and specific heat ratio values of carbon dioxide at room temperature. The gas constant of carbon dioxide is R = 0.1889 kJ/kg K.
Q4//B/ Heat is removed from airflow in a constant-area duct, if flow enters at Mach 2.20, T1= 310 K, and p1= 120 kPa. Determine exit Mach number and the amount of heat removing from the duct if the static temperature at exit section is 255 K. justify your solution for M2
Outside air at a temperature of 25°C is drawn into the duct and then heated along the duct at 234 kJ/kg. At section 1 the temperature is T = 15°C and the absolute pressure is 98 kPa. Neglect friction. (Figure 1) Figure 50 mm -2 m- 1 of 1 Determine the Mach number at section 2. Express your answer using three significant figures. M₂ = 0.915 Submit Part B Correct Determine the temperature at section 2. Express your answer using three significant figures. T2₂ = 455 K Submit Part C P₂ Previous Answers Correct Determine the pressure at section 2. Express your answer to three significant figures and include the appropriate units. Submit Previous Answers Value Provide Feedback Units Previous Answers Request Answer ? * Incorrect; Try Again; 5 attempts remaining
Air moves at 0.85 of the speed of sound when it is 120°C and 1.2 atm. Air has a specific heat of 0.25 cal/g-C and a ratio of 1.4 between its specific heat under constant pressure and constant volume. Compute the velocity of air under this situation and the stagnation temperature.
2. Carbon dioxide gas (CO2) flows adiabatically along a duct. At station 1 the static pressure P₁=120 kPa and the static temperature T1= 120 oC. At station 2 further along the duct the static pressurep2=75 kPa and the velocity C 2= 150 m/s.Determine (1) the Mach number M 2 (2) the stagnation pressure poz (3) stagnationtemperature Toz (4) the Mach number M 1 For CO 2 take R = 188 J/(kg K) and K = 1.30.
The converging-diverging nozzle(as shown in the figure given below) expands and accelerates dry air to supersonic speeds at the exit where p2 = 8 kPa and T₂ = 240 K. At the throat, p₁ = 284 kPa, T₁= 665 K, and V₁ = 495 m/s. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air- D₁ = 1 cm Kg/s D₂ = 2.5 cm Determine the mass flow for a steady compressible flow of an ideal gas.
Q.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate for a back pressure of 0 kPa. q = 250 kJ/kg Pr = 500 kPa Tr = 500°C Po = 0 kPa D= 0.02m