As shown in the Figure , an external load resistor, R, is connected across the terminal a-b of the DC circuit. Based on Norton’s Theorem, calculate and analyse the circuit shown in the figure ( given V1=60V, V2=20V, R1 = 22ohm, R2 = 34ohm, R3 = 35ohm, R4 = 42ohm,) to determine the current, i, when R = 200 Ω

As shown in the Figure , an external load resistor, R, is connected across the terminal a-b of the DC circuit. Based on Norton’s Theorem, calculate and analyse the circuit shown in the figure ( given V1=60V, V2=20V, R1 = 22ohm, R2 = 34ohm, R3 = 35ohm, R4 = 42ohm,) to determine the current, i, when R = 200 Ω

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
Shown in the figure is an RL series circuit in which R= 10 ohms and L= 0.1 Henry. This is energized by a 24 volt DC source. If the switch is closed at t=o. Find the time when Power across R = Power across L.
Given the circuit below and that R1=1.7ohm,R2=3.5ohm,Emf1=2.1V and Emf2=6.3V. What is the current through the section ac?
Consider the series-parallel circuit shown in the figure below with various multimeters connected in the circuit. Assum that XMM1 has been configured in ammeter mode, and XMM2 has been configured in voltmeter mode. XMM1 R1 1kQ XMM2 R2 R3 V1 1kQ 1kQ 12V 3.1: Redraw the circuit replacing XMM1 and XMM2 by their equivalent circuit models 3.2: Assume that XMM2 was incorrectly configured in ammeter mode. Redraw the equivalent circuit from 3.1 and compute the current that would be measured by the ammeter in this scenario. Hil-
Shown in the figure is an RL series circuit in which R= 10 ohms and L= 0.1 Henry. This is energized by a 24 volt DC source. If the switch is closed at t=o. Find the time when PR = PL.
An electric circuit with two DC power supplies is shown in Figure A (E1 and E2). Assume that E1 = 200 V, E2 = 120 V, and that all resistors have similar value of R = 20. Using the Superposition theory and the Current Divider Rule, simplify the circuit and determine the current (IR6) across resistor R6.
A dc generator and a battery are connected to a resistive load RL in the figure below. For each, determine the value of RL for maximum power transfer to RL. Next is to determine RL to 75% efficiency
Q1) For the circuits shown in figure below, obtain the equivalent resistance at terminals a-b. sa 200 ww- 20
Shown in the figure is an RL series circuit in which R= 10 ohms and L= 0.1 Henry. This is energized by a 24 volt DC source. If the switch is closed at t=o. Find the power absorbed by R and L at t=7.5 ms.
Calculate the lx current using the constant voltage model for the circuit in the figure. Circuit Parameters / Vx=12 V, VD ON=800 mV, R1=1.3 k2 Vx D1 VD a. 13.354 mA O b. 10.769 mA O c. 8.615 mA O d. 15.938 mA e. 6.462 mA
1. In your own words, state Kirchhoff's Voltage and Current law? "ULA So that:
Use superposition to compute for the DC voltage levels for node B, C, and D. The dependent current source is equal to I1=hfeIb, hfe=177. What is the dc current Ib using superposition when 15V is turned on? when the 0.7V is turned on?