As a design engineer you are asked to peer review the design done by another engineer at your organization. A typical reinforced concrete floor slab plan is given. Assume all members to be simply supported. The specified compressive strength of concrete is 5000 psi and Grade-60 steel is used. Unit weight of concrete can be assumed as 150 lb/ft³. B A 0.09 B2 -EQ. EQ.FEQ.- IS SEC 1 40'-0"- B1 B3 B3 Bl 2 The only dead load acting on the slab is the self-weight of the members. The live load on the slab is 100 psf. Initial cross-section and reinforcement details of beam B1 is shown. Area of steel is 4.8in2. EQ. 40'-0" B EQ. North

As a design engineer you are asked to peer review the design done by another engineer at your organization. A typical reinforced concrete floor slab plan is given. Assume all members to be simply supported. The specified compressive strength of concrete is 5000 psi and Grade-60 steel is used. Unit weight of concrete can be assumed as 150 lb/ft³. B A 0.09 B2 -EQ. EQ.FEQ.- IS SEC 1 40'-0"- B1 B3 B3 Bl 2 The only dead load acting on the slab is the self-weight of the members. The live load on the slab is 100 psf. Initial cross-section and reinforcement details of beam B1 is shown. Area of steel is 4.8in2. EQ. 40'-0" B EQ. North

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

Please give me the correct solution and answer this problem in principles of reinforced/presstresse concrete
Referenced concrete When designing the same bim Why is the load in the case of moment greater than the load in the case of shear?
2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above
j) What is the height of the concrete stress block if the area of steel is 3 in2, concrete strength is 4000 psi, f, 60 ksi, and the concrete width is 12 inches.
Sub: Advance Reinforced Concrete design. Follow the ACI 318 design code for the design. Answer the question with all details. provide the drawings with all details. Don't Copy Paste from Other Solutions please. i will Upvote You Value Óf X1= 27.65 Value Of X2= 395 1- Design the beam BC of the frame shown in Figure 1 for bending moment and shear force according to ACI 318 code requirements. The concrete cover is 30 mm. Dead load and live loads are given in Figure 1. Provide all drawings in detail. Please do check for maximum and minimum flexural requirements, maximum and minimum spacing of the shear reinforcement. f=X1 MPa, fy=X2 MPa D.L.=5 ton/m L.L.= 3 ton/m 6 m 3 m
Reinforce Concrete: Determine the design strength of the beam. Use F'c= 28 MPa, Fy = 415 MPa, b = 250 mm, d' = 60 mm, d = 400 mm, As = 7-25 mm bars, A's = 2-25 mm bars
A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 26.27 MPa and fy = 414 MPa. Calculate the nominal capacity based on the maximum steel area for a tension- controlled condition. Use the following dimensions: b = 498 mm d = 709 mm t = 152 mm web thickness - 152 mm b 1 I d
If the compressive strength of the concrete is 4 ksi and the yield strength of steel is 60 ksi, the value of that should be used in computing the design moment strength oMn for the beam section should be 23.5 in 1.5424 0.65 0.48 0.9 3#9 14 in 26 in
42. Permissible tensile strength of concrete, M150 is: A) 150kg/cm² C) 150N/mm² B) 15kg/cm D) 15N/mm2
Answer Options Correct Q.No Question/Statement Answer A Select the grade of concrete required for 1 М5 M50 M15 М80 airport runways. The load which has fixed size and location is 2 called as Environmental All answers Dead load Live load Load are wrong Top surface of the tensile Bottom The clear cover of the RCC beam is taken as Centre of surface of the Bottom of the gravity of the tensile steel vertical distance from the base of the beam to steel tensile steel beam the reinforcement reinforcement 4 Stocky column generally fails by_ Compression Tension Buckling Deflection In a one way slab the main reinforcement is provided along All answers Both long and short span Long span Short span are wrong All answers Flat slab is placed above Drop panels Column Column head are correct The maximum percentage of reinforcement in 7 RCC short column, based on practical 0.8% 4% 6% 2% difficulties is For reinforced concrete wall D4B When to columns are far, select the type of foundation Trapezoidal…
The design engineer specifies a concrete strength of 5500 psi. Determine the required average compressive strength for a. a new plant where s is unknown b. a plant where s 7.1 500 psi for 22 test results Questions and Problems 309 c. a plant with extensive history of producing concrete with s = d. a plant with extensive history of producing concrete with s 400 psi 600 psi
A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive bending moment of 78 kip, in psi (neglect steel reinforcement) B. If fc= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in lb/ft? 250 mm 80 mm 130 mm 80 mm 80 mm