An RLC circuit consists of a 150-Ω resistor, a 21.0-μF capacitor, and a 460-mH inductor connected in series with a 120-V, 60.0-Hz power supply. (a) What is the phase angle between the current and the applied voltage? (b) Which reaches its maximum earlier, the current or the voltage?

An RLC circuit consists of a 150-Ω resistor, a 21.0-μF capacitor, and a 460-mH inductor connected in series with a 120-V, 60.0-Hz power supply. (a) What is the phase angle between the current and the applied voltage? (b) Which reaches its maximum earlier, the current or the voltage?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter24: Resistive-inductive-capacitive Parallel Circuits

Section: Chapter Questions

Problem 1RQ: An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in...

See similar textbooks

Related questions

Q: A given RLC circuit (Resistor-Inductor-Capacitor) has the following components: R = 4.4 Ohms L =…

A: The reactance offered by capacitor in RLC circuit (XC) is given by: Where, The capacitance of…

Q: 2. Please find the time constant and capacitance value (C) of a simple RC circuit by using its…

A: The given curve is a discharging curve of capacitor whose equation is given as: If t=RC then the…

Q: A series RLC circuit having a resistance of 8 ohm, inductance of 50 mH and capacitance of 90 µF is…

A: We have been give an RLC circuit with, Resistance (R) = 8 Ω Inductor (L) = 50 mH = 50 * 10-3 H…

Q: Find the equivalent capacitance (µF) seen at the terminals of the circuit below. 50µF 60µF Ceq 70µF…

A: By series and parallel combination of capacitor we will find out equivalent capacitance .

Q: a) A 20 nH inductor has a seri tance of 15 2. Compute the eq parallel resistance, Rp, at 2 G b)…

Q: Ks) Obtain the steady-state voltages at the nodes of the following circuit. All capacitances are 0.1…

A: When the gate terminal of the PMOS and the NMOS is active, the transistor is short-circuited. The…

Q: 2. Please find the time constant and capacitance value (C) of a simple RC circuit by using its…

A: To solve above question, one should understand the behavior of Inductor and capacitor in DC circuit.…

Q: A series RLC circuit is constructed employing component values R = 100 Sa and L = 1.5 mH along with…

A: In this we will find Capacitance C with help of data...And find impedance and current for series…

Q: The capacitor of external defibrillator must be loaded at 1500V, in order to generate a two-phase…

A: CAPACITOR: Any two conducting surfaces separated by an insulating material is called a capacitor od…

Q: For the network shown below, the switch is closed on to position 1 when t = 0 and then moved to…

A: When switch is at ⊥when switch at t∘ = 20ms more to 2Capacitor will start dischargingV(t) = V,co')…

Q: A parallel RLC circuit containing a resistance of 1.5kΩ, an inductance of 0.15H and a capacitor of…

Q: Circuit analysis 2

Q: Consider the given circuit with vi=3V, R1=20K, Rf=50K, R2=10K, R3=20K, C=2μF. Assuming that the…

A: In this question we will find output voltage of opamp...

Q: In a series RLC circuit, the source voltage is given by vi=20cos(wt), where w=1000rad/s, the…

Q: An RIC series circuit has R = 2 ohms. L= 20 mH, and a variable capacitance Cas shown below. The…

Q: usé differential equation method to: 1. Find the initial capacitor voltage V (t0) when switch moves…

A: We need to find out voltage across capacitor in given circuit

Q: 7. The partial phasor diagram (not to scale) in the picture represents a series RLC circuit with…

Q: Consider the following RLC circuit, composed of a resistor R = 40 in series with a o capacitor C =…

Q: A series RLC circuit is connected across a 110V, variable frequency source. When the frequency is…

Q: In a series RLC circuit, if the value of the pure capacitance is decreased as one-third the value of…

Q: A series RLC circuit has resistance of 4 ohms, 100MH inductance and 70.4 micro-farad capacitance. It…

Q: For the circuit shown below, find the equivalent inductance L_eq. All inductors are given as 25 mH.

Q: A series RLC circuit has a resistance of 30 ohms, a capacitance of 10-2 Farads, an inductance of 5…

Q: An RLC series circuit is powered by a 120-V, 60-Hz supply. It contains a capacitor that has an XL of…

A: Third option is correct. The detailed solution is provided below.

Q: A coil, resistor, and capacitor are in parallel. The resistance is 1 Ω; the capacitive susceptance…

Q: 2. Please find the time constant and capacitance value (C) of a simple RC circuit by using its…

A: Graph is given as :

Q: THE FORCED RESPONSE COMPONENT OF THE CAPACITOR VOLTAGE FOR THE CIRCUIT IN FIG. IS 4 ΚΩ 2 ΚΩ 12 KQ² 1…

Q: Electrical Engineering Gcopper = 5.813×10" (Nm)', µo=4xx107 H/m, o-8.85x1012 F/m a) Find the high…

A: Given: Consider the parameters: σcopper=5.813×107 Ωm-1μo=4π×10-7 H/mεo=8.85×10-12 F/m To find: (a)…

Q: Consider the following RLC circuit, composed of a resistor R = 4N in series with a o capacitor C =…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: RLC Circuit (Vo) is 75 V and the initial current through the inductor (I,) is 30 mA... Find v(t),…

Q: 4.) A series RLC circuit with R = 3000 ohms, L = 10 H, C = 200 microfarad has a constant voltage V =…

Q: An RLC series circuit contains an unknown capacitor, an inductor with an inductance of 40 mH, and a…

A: Given data, Inductance L = 40 mH Resistance R=16 Ω Voltage V = 240 V Frequency f = 60 Hz Current i =…

Q: 2. Please find the time constant and capacitance value (C) of a simple RC circuit by using its…

A: In an electric circuit, the transients are due to energy storing elements. If the network contains…

Q: a Source hee RC cirtuit· 'vit) =) VCE) = ½(t) Tet vo)=Vo KCL at node A' ie (t)+ict)=0 PLEASE HELP ME…

Q: An RLC series circuit has R =2 ohms, L 20 mH, and a variable capacitance C as shown below. The…

A: To solve the above problem, one should have a basic idea about the working of AC circuits. The…

Q: 2. Change the values in the RLC circuit above to R = 2.5 Q, L = 25 mH, and C = 2.367 mF. Find (a)…

A: "Since, you have asked for a handwritten solution, according to our guidelines, we cannot provide…

Q: 3 F 6 F C H 3 F 4 F The equivalent capacitance is |F.

A: The given circuit is shown below: In the above circuit, the 3F and 6F capacitances are connected…

Q: In a series RLC circuit, if the value of the pure capacitance is decreased as one-third the value of…

A: Right Answer option False

Q: b) For the circuit shown, assume that the capacitor volitage and inductor current are zero at t = 0.…

A: ELECTRICAL NETWORK: When addressing a circuit problem or constructing a balanced circuit, the word…

Q: The voltage 8 sin (400t) is applied to a series RLC circuit, with R = 200 Q, L = 0.1 H, and C = 1 µF…

Q: A coil having a 240V source has a current of 10.5 A when the frequency is set to 60 Hz. When the…

Q: Given a 10V AC source at 100HZ in an RC circuit with capacitance of 220NF and resistance of 510…

Q: Consider the following RLC circuit, where vs(t) = 240 cos(wt) (V), operating at 60HZ. %3D Calculate…

Q: For the shown LC circuit, the switch closed at t=0. If C = 323 µF, L = 20 mH, and E = 200 V, then…

A: Given that E=200VL=20 mHC=323 μFt=5 ms Draw the s-doamin circuit of given circuit diagram Apply…

Q: 2. Please find the time constant and capacitance value (C) of a simple RC circuit by using its…

A: Given that R=60 kΩ The capacitor current in the RC circuit is given by the below formula,…

Q: A certain RLC circuit has a voltage of 180 volts, a resistor of 12 ohms, an inductor of 1.5 henries,…

A: Given, it is a series RLC circuit. R = 12 ohm , L= 1.5 H, C = 1/1950 F

Q: 4- Finding the Roots of the Characteristic Equation of a Parallel RLC Circuit. a) Find the roots of…

Q: In a short circuit test conducted on a circuit breaker, the maximum restriking voltage is observed…

A: Maximum re-striking voltage, Vm=160kV

Question

An RLC circuit consists of a 150-Ω resistor, a 21.0-μF capacitor, and a 460-mH inductor connected in series with a 120-V, 60.0-Hz power supply. (a) What is the phase angle between the current and the applied voltage? (b) Which reaches its maximum earlier, the current or the voltage?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
List the five capacitor replacement rules.
What frequency must be applied to a 33-mH inductor to produce an inductive reactance of 99.526 ?
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in parallel. The circuit is connected to a 240-V, 400-Hz power supply. Find the following values. XL=XC=IR=AIL=AIC=AP=WVARsL=VARsC=IT=AVA=PF=%=
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.
.A series RLC circuit contains a 4-kN resistor, an inductor with an inductive reactance (X,) of 3.5 kn, and a capacitor with a capacitive reactance (Xc) of 2.4 kN. A 120-Vac, 60-Hz power source is connected to the circuit. How much voltage is dropped across the inductor?
The figure below shows a simple RC circuit with a 3.30-μF capacitor, a 4.40-M resistor, a 9.00-V emf, and a switch. What are the following exactly 9.00 s after the switch is closed? (a) the charge on the capacitor 13.7204 UC (b) the current in the resistor 0.0110522 x Your response is off by a multiple of ten. HA (c) the rate at which the capacitor is storing energy μW (d) the rate at which the battery is delivering energy μW
Consider the parallel RLC circuit of Figure 2 with the source a 1-kHz sinusoid having an amplitude of 5 V. Regard the source voltage as having zero phase. Calculate the amplitude and phase (in degrees) of the following quantities: the current through the resistor, the current through the inductor, and the current through the capacitor. Calculate also the amplitude and phase of the current supplied by the source.
Please explain this question properly A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (I, in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1. and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. If the value of R2 =1600 Ohm then the input voltage (in volts) is: 7.5 25 110 Frequency H2 O a. 4 O b. 16 sin(9888 t) O c. 8 O d. 8 cos(6.28 f t) O e. 8 sin (6.28 R t)