An open cylindrical tank 30 cm, in diam. and80 cm, high partially filled with water is rotatedabout its vertical axis at a speed of 240 rpm.a. What would be the depth of water in thetank if the cylindrical tank is brought to restso that no water will be spilled out.b. At what speed would it be rotated so that1.40 liters of water will be spilled outC. At what speed would it be rotated so thatthe pressure at the center of the bottom ofthe tank is zero?

Answered: Image /qna-images/answer/6a46f27d-d9e7-4b2a-bc61-8e45dfe5dd5d.jpg

An open cylindrical tank 30 cm. in diam. änd 80 cm, high partially filled with water is rotated about its vertical axis at a speed of 240 rpm. a. What would be the depth of water in the tank if the cylindrical tank is brought to rest

An open cylindrical tank 30 cm. in diam. änd 80 cm, high partially filled with water is rotated about its vertical axis at a speed of 240 rpm. a. What would be the depth of water in the tank if the cylindrical tank is brought to rest

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cylindrical tank, filled with water and axis vertical, is open at one end and closed at the other end. The tank has a diameter of 1.2m and a height of 3.6m. It is then rotated about its vertical axis with an angular speed w. a. Determine w in rpm so that one third of the volume of water inside the cylinder is spilled. b. Determine the largest pressure developed in the tank.
L11)! 111 1........ Date No. A differential manometer is connected. at two poins A and B of two pipes as Shown on the belw figure, The pipe A Contains a liquid of sp.gr= lo5 while B contains aliquid of sp.gr=0.9. The pressure. at A and B are 9.81 X l04 N/M and 1.8 X 10u N /my respectively. Density ot mercury 13.6 g/cn². Find the difference în mercury level in the diffenential mano meter. sp.gr=Dl05 3m 2.0 Sp.gr=o9
Oil flows from a tank through 150 m of 150 mm pipe and then discharges into air as shown. If the head loss from pt. 1 to pt. 2 is 600 mm, determine the pressure needed at pt. 1 to cause 17 Liters/sec of oil to flow. El. 30 m Air, p El. 20 m Oil S = 0.84 а. 87.74 kPa b. 24.73 kPa c. 60.66 kPa d. 36.58 kPa 150m-150 mm Ø
3. A pump is discharging 12 lit/sec of water through 100mm diameter smooth steel pipe. When the pump is 700 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assuming f = 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 100 mm dia. 45.0 m 540 m
i) Which of the following statements about a straight horizontal pipe of 6 inch diameter pressurized pipe carrying water is incorrect? i) The EGL and HGL are parallel to each other. ii) The friction head is equal to the loss in pressure head. iii) The velocity head gradually decreases from the beginning to end of the pipe. iv) The EGL (or) TEL is above the HGL. Answer: ii) Water flows from a 0.75 m pipe into a 1 m pipe. If losses are neglected then the 1 m diameter pipe will most likely (i) Have higher velocity than 0.75 m pipe (ii) Be at the same pressure as the 0.75 m diameter pipe (iii) Be at a higher pressure than 0.75 m pipe (iv) Be at a lower pressure than 0.75 m pipe. Answer:
Homework 14 |A cylindrical vessel closed at the top and bo om is 300mm inn diameter, 1m long and contains water up to a depth of 0.8m. The air above the water surface is at a pressure of 60 KPa. If the vessel is rotated at a speed of 250n rpm about its ver cal axis, nd the pressure head at the bo om of the vessel at the center point and at the edge.
4.) A 75 mm diameter pipe, 2 m long is just filled with oil (sp. gr. = 0.822) and then capped, and place on horizontal position. It is rotated at 27.5 rad/sec about a vertical axis 0.5 m from one end (outside the pipe). What is the pressure in kPa at the far end of the pipe? Answer: 1865 Kpa Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
10.The 600-mm Ø pipe shown conducts water from reservoirA to a pressure turbine which discharges through another600-mm Ø pipe into the tail-race at B. The loss of headfrom A to 1 is 5 times the velocity head in the pipe andthe loss of headfrom 2 to B is 0.2 times the velocity head in the pipe. If the discharge is 700 li/s. a.Compute the hp given up by the water to the turbine. b.Compute the pressure head at 1. c.Compute the pressure head at 2.
11- In an infinite two-dimensional flow filed, a sink of strength 3/2n m/s.m is located at the origin, and another of strength 4/2n m'/s.m at (2 , 0). What is the magnitude and direction of the velocity at point (0, 2). [0.429 m/s; -68.22°]
Water flows to a circular pipe with a constant raduis of 10 cm. the speed and pressure at point A is 4 m/s and 250 000Pa respectively. a.Whatis the speed of the fluid at point B b. What is the pressure at point B which is 10m higher than point A?
An open cylindrical tank, 6 ft high and 3 ft in diameter, contains 4.50 ft of water. If the cylinder rotates about its geometric axis, (a) what constant angular velocity can be attained without spilling any water? (b) What is the pressure at the bottom of the tank at Cand D (Fig. 5-6), when a) = 6.00 rad/sec? 5.
A pump is located near the edge of the horizontal platform shown. The nozzle at A discharges water with an initial velocity of Vj = 28 ft/s at an angle of e = 50° with the vertical. Determine the range of values of the height h for which the water enters the opening BC. h в с 22 ft 6 ft