An op amp-based high-pass filter with a cutoff frequency of 12 kHz and a passband gain of 5 is shown in (Figure 1). If the capacitor has a capacitance of 75 nF, what are the values of R1 and R2? Express your answers in ohms to three significant figures separated by a comma. Figure 1 of 1> ΑΣφ vec ? R2 R1, R2 = Ω R C Submit Request Answer Part B Complete previous part(s)

An op amp-based high-pass filter with a cutoff frequency of 12 kHz and a passband gain of 5 is shown in (Figure 1). If the capacitor has a capacitance of 75 nF, what are the values of R1 and R2? Express your answers in ohms to three significant figures separated by a comma. Figure 1 of 1> ΑΣφ vec ? R2 R1, R2 = Ω R C Submit Request Answer Part B Complete previous part(s)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 1PA: You are an electrician working in a plant. A series resonant circuit is to be used to produce a high...

See similar textbooks

Similar questions

a simple capacitor filter has an input of 40V dc. if this voltage is fed through an RC filter section (R=50 ohm, C=40 micro farras). what is the load current for a load to resistance of 500 ohm
I need some help. I am designing a bandpass filter with fl=3400 Hz and fh= 7500 Hz. Based on that I need the values for the RCL circuit, assuming that the capacitor is 1 microfarat. So, I need some help in calculate the center frequency, bandwith, Q, center frequency as well. I need clear steps and calculations. Any help will be appretiated.
I want the answer in detail and as quickly as possible please Q/ Using capacitors and resistors, design A - (band-pass filters) with Fl=105HZ and Fh=115HZ. B - Design (band-pass filters) with FI = 215HZ and Fh = 225HZ.
Design a low-pass filter using a 100 mH inductor and a single resistor R to obtain a cutoff frequency of 7500 Hz ± 2%. In your notebook, show your design procedure, including your design calculations Can you do this written out please anf thank you!
An RC low-pass filter is shown in the figure. Its purpose is to attenuate higher frequencies while allowing lower frequencies to pass through. A 960-Hz sine-wave signal with rms amplitude of Vrms = 1.9 V is fed into the filter. The values of the components are R = 120 Ω and C = 0.64 μF and Vout-rms = 1.724 V. By what angle, in degrees, does the output voltage lag the input voltage?
We will use magnitude comparator and a Quad 2-to-1 MUX. How ?
Identify the reason for a nonsinusoidal signal being distorted when it passes through a filter. -The distortion occurs because harmonics are removed or rejected, leaving a different waveshape. -The distortion occurs because harmonics are synchronized, leaving a different waveshape. -The distortion occurs because the signal is modulated, leaving a different waveshape. -The distortion occurs because harmonics are added in the filter, leaving a different waveshape.
Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 200Hz and a higher cut-off frequency of 800HZ. Fa Pau tand Pan Bard Fregarey Lon Pan High Pam Raspon Raspone Figure 1: Band Stop Filter Characteristics Assuming a capacitor, C value for both filter sections (CLP, CHP) of 0.2ur, calculate the values of the two resistors, RuP and Rup using the formula: 1. From the Low pass filter formula, Find RLp: 1 fi = 2. From the High pass filter iormula, Find Rup: 1 fu = 2nRupCuP 3. Calculate the center frequency (fe) and Bandwidth (BW): a. fc = VfL x fu b. BW = fu - fL
Design a series RLC bandpass filter as shown in the figure with lower cut-off frequency f = 400 Hz and bandwidth B = 9600 Hz %3D a) Determine the higher cut-off frequency f# b) Determine the center or resonant frequency fo in Hz and wo in rad/s and calculate the quality factor Q c) Choose C = 2 nF and find the values of R and L to meet the design specifications C No V: O
The following figure shows a system that couples an inverting band pass filter with a high pass filter. Using parameters given in the figure, derive the transfer function of Vo(s)/Vi(s) Vi Inverting band pass filter R₁ ww C₁ C₂ R₂ High pass filter C3 R3 R4 R5 Vo Hint: You could start with writing the transfer function of the two filters separately, then combine the two equations into one. Your transfer function may be written as the product of multiple filters and/or gain stages - you do not need to reduce to simplest form but you should have each piece derived somewhere.
Required information The circuit shown in the given figure is an active filter. Assume C=15 nF. Ro 4 kohm, R₁-1.2 kohm, R₂ =29.4 kohm, and R3=97.7 kohm. NOTE This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. ww www R₁ C Determine the cutoff frequencies www 20 The cutoff frequencies w₁ and 2 are X 103 and 104, 4, respectively.
Design an active lowpass filter with dc gain of 0.5 and corner frequency of 250Hz. Then draw the circuit diagram for this filter.