An inside cylinder locomotive has its cylinder centre lines 1 m apart and has a stroke of 1 m. The rotating masses per cylinder are equivalent to 100 kg at the crank pin, and the reciprocating masses per cylinder to 200 kg. The wheel centre lines are 2 m apart. The cranks are at right angles. The whole of the rotating and 2/3 of the reciprocating masses are to be balanced by masses placed at a radius of 0.8 m. Find the magnitude of the balancing mass on the right most wheel. Select one:

Q: The cranks and connecting rods of a four cylinder in-line engine running at 2000 rpm are  60mm and…

A: Given that, ω=2πN60ω=2π200060ω=209.45 rad/sec,   r=60 mm=0.06 m,l=240 mm=0.24 m,m=1.5 kg,   1.…

Q: A shaft carries four masses A, B, C and D with a a magnitude of 200kg, 300kg, 400 kg and 200 kg…

A: Draw the table from given data. Let mx and my are the balanced force in x and y-directions. Plane…

Q: A shaft carries four masses A,B,C and D of magnitude 220 kg, 320 kg, 420 kg and 220 kg respectively…

A:

Q: A 3.6 m long shaft carries three pulleys, two at its two ends and third at the mid-point. The two…

A: L=3.6mmA=79kgmC=40kgCGA=3mm=0.003mCGC=5mm=0.005mmB=50kgCGB=8mm=0.008mN=300rpm=2×π×N60=2×π×30060=31.4…

Q: The figure shows a rotor with three unbalances on it. To the L and R balancing planes given in the…

A:

Q: 2.2 A 2.2-tonne racing car has a wheel base of 2.4 m and a track of 1.4 m. The centre of mass of the…

A: (a) To find: The load distribution on the wheel when the car turns left. Given: The mass of racing…

Q: 6. A shaft with 3 metres span between two bearings carries two masses of 10 kg and 20 kg acting at…

A:

Q: Problem 1 1.Four masses m1, m2, m3 and m4 are 200 kg, 300 kg, 240 kg and 260 kg respectively. The…

A:

Q: Q) A SINGLE CYLINDER HORIZONTAL ENGINE RUNS AT 120 R.P.M. THE LENGTH OF STROKE IS 400 MM. THE MASS…

A: The solution is given in next step

Q: A rotating shaft carries four masses A, B, C and D which are radially attached to it. The mass…

A: Given information: The values of the four mass: ma=7.5 kgmb=m kgmc=5 kgmd=4 kg The radial distance…

Q: A vertical bar of length L with mass of 40 kg is rotated vertically about its one end at 40 rpm.…

A:

Q: 1) Diagram below shows four masses M,E,R,S carried by a rotating shaft at radii 100, 125, 200 and…

A: There will be many forces acting on a reciprocating engine, there will also be inertial forces. The…

Q: The following data apply to an outside cylinder uncoupled locomotive: Mass of rotating parts per…

A: Given Mass rotating parts = 250 kg Mass reciprocating parts = 200 kg Crank angle = 900 Crank radius…

Q: An oversized yo-yo is made from two identical solid disks each of mass  M = 1.90 kgand radius R =…

A:

Q: Two flywheels of negligible mass and different radii are bonded together and rotate about a common…

A:

Q: |DG,| = 2|G,G,| %3D Ga ma L |DG,| = = Do mp Gp ° E T |AE| = |CD| = L L, m L, m А g = 9.81 m/s2 C

A:

Q: Q) A rotating shaft carry four unbalanced masses 12kg, 8kg, 10kg and 6kg at radii 4cm, 5cm, 6cm and…

A: Solution

Q: Regarding the gyroscope illustrated below, consider that you give a push for a brief moment on the…

A: The precessional angular velocity of shaft for gyroscopes is given by right hand screw rule. For the…

Q: A single cylinder reciprocating engine has speed 240 rpm, reciprocating mass of 50kg and crank…

A: Centrifugal Force due to a rotating mass causes imbalance, by attaching a counterweight at a…

Q: A shaft carries four masses A, B, C and D of magnitude 200 kg. 300 kg. 400 kg and 200 kg…

A:

Q: 5. A uniform solid cylinder with M 2R mass M and radius 2R rests on a M horizontal tabletop. A…

A:

Q: QI: The cutter bar of a mower is connected to the P.T.O. shaft of a tractor making 1500 stroke per…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: A wheel radius 0.4meter has mass 3kg se figure. Center of wheel goes a rope to point A, the wheel…

A:

Q: Three bodies are fixed on a shaft rotating at 500 rpm. The mass of the bodies are 3.5 kg, 2.5 kg and…

A: We will have to find out the radial and angular position of the balancing mass

Q: The figure below shows, at left, a solid wheel of radius R = 0.600 m and mass 70.0 kg. Mounted…

A: Given data: The radius of the wheel is r = 0.600 m. The mass of the wheel is M = 70 kg. The radius…

Q: Problem 1: A uniform thin rod of mass m = 4.4 kg and length L = 1.2 m can rotate about an axle…

A: Given question belongs to the Engineering Mechanics subject. Can solved by using formula, 》 Net…

Q: disc density is not perfectly uniform because it not perfectly manufac disc perfectly mounted on the…

A:

Q: The structure of a football goal is shown in the figure below. The bending motion of the structure…

A: When the soccer ball hits the crossbar then apply the conservation of linear momentum, Here, vo is…

Q: A single cylinder horizontal engine runs at 120 r.p.m. The length of stroke is 400 mm. The mass of…

A: As per given question we have find the magnitude of the unbalanced force due to the balancing mass

Q: 2. Four masses m1, m2, m3 and m4 are 200 kg, 300 kg, 240 kg and 260 kg respectively. The…

A:

Q: 1) Consider the figure below. The inside radius is 0.25 m and the outside radius ís 0.4m. a) What…

A:

Q: Q4:-A rotating shaft carries four masses 176.6 N, 137.3 N, 157 N and 117 N at radii 5 cm, 6 cm, 7 cm…

A: The masses of the shaft is given as, m1=176.6 Nm2=137.3 Nm3=157 Nm4=117 N The radii of the rotating…

Q: Two thin hoops of masses m1 and m2 have radii a1 and a2, respectively. They are mounted rigidly on a…

A: Solution: It is given that two thin hoops of mass m1 and mass m2 are placed at a distance a1 and a2.…

Q: A 30kg mass is tied to a uniform rod whose mass and length are 80-kg and 8-m, as shown below. The…

A: Draw the free body diagram of the 30 kg mass: Consider the equilibrium of vertical forces:…

Q: 20. A car is moving on a curved horizontal road of radius 100 m with a speed of 20 m/s. The rotating…

A: Given data :  The radius of the curved road is r = 100 m. The speed of the car is v = 20 m/s. The…

Q: Problem No. 5 A rotating shaft carries four masses A, B, C and D rigidly attached to it; the centers…

A: When any number of masses are attached to a rotating shaft, it exerts centrifugal force on the shaft…

Q: Q2: - An aeroplane makes a complete half circle of 50 metres radius, towards left, when flying at…

A:

Q: A skier is pulled by a rope exerting a horizontal force T=0.8 kN at a distance h= 39 cm above the…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: m1 m2 m3 m4 el e2 e3 e4 alfa beta L1 L2 L3 L4 L5 (kg) (kg) (kg) (kg) mm mm mm deg. deg. mm mm mm mm…

A: There may be unbalanced forces in any system having a rotating or reciprocating element due to the…

Q: Consider a 2-cylinder inline reciprocating internal combustion engine (RICE) with a cross-plane…

A: Given data2- Cylinder inine reciprocating internal combustion engineCylinder 2 fires 2700 after…

Q: B The shaft shown in the figure rotates at a constant speed of 1500/π rpm. Three masses rotating…

A:

Q: A window cleaner is pulling himself up to a pulley that consists of two disks welded together as…

A:

Q: A shaft has three eccentrics of mass 1kg each. The central plane of the eccentrics is 50 mm apart.…

A: Given : M1 = M2 = M3 = 1 kg r1 = 20mm, r2 = 30 mm, r3 = 20 mm Let two unknown masses be MA and MB.…

Q: . Two shafts A and B whose axes are intersecting but inclined to each other at 20° are connected by…

A: Answer: The maximum torque in shaft B is 1117.55 kN•m.

Q: In reference to the figure below, if us = 0.2 at the rear drive wheels B of the 1.5 Mg vehicle with…

A:

Q: A single cylinder horizontal engine runs at 120 r.p.m. The length of stroke is 400 mm. The mass of…

A:

Q: A rotating shaft carries four masses A, B, C and D which are radially attached to it. The mass…

A: GIVEN: MA=7.5KgMC=5KgMD=4KgRA=30mmRB=38mmRC=40mmRD=35mm The axial distance between the planes of…

Q: m1 m2 m3 m4 el e2 e3 e4 alfa beta L1 L2 L3 L4 L5 (kg) (ke) (kg) (kg) mm mm deg deg. mm mm mm mm mm…

A: There may be unbalanced forces in any system having a rotating or reciprocating element due to the…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.