An elliptical plate, major axis 6 feet and minor axis 4 feet, is submerged vertically until its minor axis lies in the surface of the water (weight density =p Ib/fr3). Determine the appropriate integral to be used to determine the force on one side of the submerged

An elliptical plate, major axis 6 feet and minor axis 4 feet, is submerged vertically until its minor axis lies in the surface of the water (weight density =p Ib/fr3). Determine the appropriate integral to be used to determine the force on one side of the submerged

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Related questions

Q: H.W1 The beam is subjected to the linearly varying istributed load. Determine the maximum deflection…

A: Given Length = L Load, P = w0 Find Deflection

Q: magnitude of the force produced in member CD is

A: Given data; Figure shows an idealized plane truss; Force,F=300 NIt is applied at point A.…

Q: For a certain polyatomic ideal gas the value of its ideal gas constant is 0.123 kj/(kg.k).…

Q: A block having a weight of 8 lb is suspended from a spring having a stiffness k = 40 Ib/ft. If the…

Q: Find the strain Initial length=102.78 mm Change in length=0.004 mm

Q: b) Air flows through a cylindrical duct at a rate of 2.3 kg/s. Friction between air and the duct and…

A: Given: For air, The mass flow rate, m = 2.3 kg/s The inlet temperature, T1 = 450 K The inlet…

Q: Show by means of suitable diagrams the locations of I.D. and F.D. fans in cooling tower and boiler…

A: ID fans are also known as induced drafts fans. This is a type of exhaust fan that remove all the…

Q: 631. Determine the value of the couple M for the beam loaded as shown in Fig. P-631 so that the…

Q: 3.29 Calculate magnitude and location of the resultant force of water on this annular gate. 1m Water…

A: magnitude is 15.602 kN

Q: 0.6 kg of a gas mixture of N₂ and O₂ is inside a rigid tank at 2.7 bar, 70°C with an initial…

Q: H.W4 Determine the slope of the simply supported beam at A and deflection at C. E = 200 GPa and I =…

Q: the net heat input per unit length of the weld.

A: Given data; A gas tungsten arc welding operation is performed usingcurrent=650 A, voltage=10 V…

Q: 1) A 6061-T6 aluminium alloy flat, simply supported disk valve of 0.2 m diameter and 10 mm thickness…

A: following is the solution to the above problem-

Q: Find and solve at least 10 problems (5 easy and 5 hard) for Work and Energy

A: Given Work and energy To find 10 problems

Q: or the given beam: (a) Which of the following is the vertical reaction at c. [ Select] (b) Which of…

A: According to the details provided in the question, we need to calculate vertical reaction at A…

Q: A gas tungsten arc welding operation is performed using a current 140 A and arc voltage of 15 V at a…

Q: Determine the magnitude of the vertical deflection of

A: Given data; For a cantilever beam data given as; L= 2 m EI=200 N.m2 MA=2 mFind magnitude of the…

Q: 2. What is oxy-acetylene welding flux? Is there a welding rod coated already with flux? What is the…

A: Oxy acetylene welding is the welding process in which mixture of oxygen and acetylene gas is used…

Q: 12) Mention two instruments used to measure internal linear dimensions.

A: Q12) Mention two instruments used to measure internal linear dimensions.,

Q: Using the Griffith criterion, what is the strength of a piece of soda-lime-silica glass that…

A: The strength of a piece of soda-lime-silica glass is 102 MPa.

Q: Find the velocity K⋅E=23-SJ m = 2.3kg

A: Given data : Kinetic energy=K.E Mass=m To find : Velocity

Q: H.W3 Determine the slope and deflection of end A of the cantilevered beam. E = 200 GPa and I =…

Q: In order to measure an external tapered angle you must have A. The sine bar and gage blocks B. Two…

Q: Petermine the displacement W= 0-589 J F = 0-3 N

A: Given data : Force=F Work done=W Required : Displacement

Q: the reading in mm is T

A: This question is based on the concept of vernier calipers and reading.

Q: Task 1 The beam is shown in figure, determine the internal shear force and bending moment in the…

Q: 2. What is oxy-acetylene welding flux? Is there a welding rod coated already with flux? What is the…

A: Oxyacetylene welding is also known as oxy-fuel welding in this welding the process relies on the…

Q: mass flow rate of the liquid

A: Given data; Blade outer radius,r=50 mm It consumes power,P= kWN= 3000 rpm Determine mass flow rate…

Q: 5 Calculate the forces in members AC, AD, and DE for the loaded truss. Restraining link BC is…

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 30800 ksi] bars (1) and (2) are…

Q: the reading of this tool is

Q: If the gauge pre ssure in a 50-gal tank half-filled with liquid is 100 lbf/in .2, what would be the…

Q: Determine the magnitude of the vertical deflection of

A: Given data; Flexural rigidity,EI=200 N.m2Applied moment,Ma=1 mLength,l=2 mDetermine the magnitude of…

Q: 1. Using the phase diagram for compound X on the right, answer the following questions. Liquid B 285…

A: Given data The given phage diagram of compound X…

Q: partition. One compartment contains 3 kmol of N₂ at 600 kPa pressure and the other compartment…

Q: A model of an aircraft is being tested in a wind-tunnel. If the model was replaced by one that is…

Q: 5-An 80-L rigid tank contains an ideal gas mixture of 5 g of N₂ and 5 g of CO₂ at a specified…

Q: Shown in the figures (1) and (2) are trusses containing members that are made of same materials…

A: following is the solution to the above problem-

Q: Water flows at 67 C inside a 2.5 cm inside diameter tube such that hi = 3500 W/m² .C. The tube has a…

Q: ᴀ ᴄᴇɴᴛʀɪꜰᴜɢᴀʟ ᴘᴜᴍᴘ ᴡɪᴛʜ 76ᴍᴍ ᴅɪᴀᴍᴇᴛᴇʀ ɪᴍᴘᴇʟʟᴇʀ ᴅᴇʟɪᴠᴇʀꜱ 38ʟ/ꜱ ᴏꜰ ᴡᴀᴛᴇʀ ᴀɢᴀɪɴᴛꜱ ᴀ ᴛᴏᴛᴀʟ ʜᴇᴀᴅ ᴏꜰ 107ᴍ…

Q: A potential flow model of flow over a circular cylinder is described by the following velocity…

A: Write the expression of velocity potential. ϕ=U∞cosθr+R2r2 Calculate the velocity components.…

Q: Frid the potential energy

A: Given data : Mass=m Height=h Acceleration due to gravity=g To find : Potential energy

Q: Explain the answer and include an illustration. Why do distorted amorphous polymers have more…

A: INTRODUCTION: Polymers are distinct from other forms of materials due to their large molecular…

Q: Air with mass of 16 kg is heated at constant gage pressure of 9044 hPa from -24.0 °C to 184 °C.…

Q: At inlet, in a steady flow process, 1.5 kg/s of nitrogen is initially at reduced pressure of 2 and…

A: Given Datam˙=1.5kg/sCP=1.039kJ/kgK△T1=1.3△T2=1.7 We can take the temperature directly for difference

Q: Determine the mass fow rate of the liquid through the pump?

A: Given data; Entry of liquid into the pump is axial and exit from the pump is radial with respect to…

Q: ᴀ ᴘᴇʟᴛᴏɴ ᴡʜᴇᴇʟ ɪꜱ ᴛᴏ ʙᴇ ᴅᴇꜱɪɢɴᴇᴅ ᴛᴏ ʀᴜɴ ᴀᴛ 400ʀᴘᴍ ᴜɴᴅᴇʀ 150ᴍ ᴇꜰꜰᴇᴄᴛɪᴠᴇ ʜᴇᴀᴅ. ᴛʜᴇ ʀᴀᴛɪᴏ ᴏꜰ ᴛʜᴇ ɴᴏᴢᴢʟᴇ…

A: Given pelton wheel turbineN=400rpmH=150mdD=112η=84%=0.84speed ratio=0.55

Q: Compute the moment of area of the M diagram between the reactions about both the left and the right…

Q: Fnd the Face others = 22-5 N/mm Area = 3mm² 2

A: Given data : Area=A Stress=σ To find : Force

Q: Shown in the figures (1) and (2) are trusses containing members that are made of same materials…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
A hemispherical plate with diameter 10 ft is submerged vertically 1 ft below the surface of the water. Express the hydrostatic force against one side of the plate as an integral and evaluate it. (Round your answer to the nearest whole number. Recall that the weight density of water is 62.5 lb/ft3.)
An isosceles triangle, base 18 ft and altitude 24 ft, is immersed vertically in oil of specific gravity 0.800with its axis of symmetry horizontal. If the head on the horizontal axis is 13 ft, determine the total forceon one face of the triangle and locate the center of pressure vertically.
4. A heavy car plunges into a lake during an accident and lands at the bottom of the lake on its wheels. The door is 1.2 m high and 1 m wide, and the top edge of the door is 8.8 m below the free surface of the water. Determine the hydrostatic force on the door and its location from the free surface. 8.8m Z Lake
A barrel in the form of a frustum of a cone with a radius of 3m and 6m at the bottom and at the top respectively. It is 5m high and is 4/5 full of oil (0.83). Determine the a. Total hydrostatic force "F" acting on the wall of the barrel in kN and b. its line of action "s" from the bottom
4. Find the force on the following triangular submerged plate in water and location of its center of pressure using integration method. ----- 7m 4 m 3.25 m
A semicircular gate with a diameter of 6 ft is installed at 50º as shown below. The top of the gate is 5 ft below the water surface. Determine the resulting hydrostatic force and the location of the center of pressure on the gate.
In the Fig. is shown the cross-section of the tank full of water under pressure. The length of the tank is 2.5 m. An empty cylinder lies along the length of the tank on one of its corners as shown. Find the horizontal and vertical components of the force acting on the curved surface LMN of the cylinder
This Utah-shaped plate is submerged in oil, (s=0.94) and lies in a vertical plane. Find the magnitude and location of the hydrostatic force acting on one side of the plate. * Oil surface 1.5 m 1.5 m 4.6 m 2.6 m 3.8 m O 4.27 4.47 O 4.67 4.87
5. A 3-m-long (in the direction perpendicular to the paper) curved gate is located in the side of a reservoir. The gate forms a quarter of a circle whose radius is 2 m. Determine the magnitude of the horizontal and vertical components of the force that is required to hold the gate in place (ignore the self weight of the gate). 6 m Water X-2 2 m Gate
2- A tank containing water is shown in Fig. Calculate the total resultant force acting on side ABCD of the container and the 6 ft location of the center of pressure. IF 62.4 Ib/ft3 Y = Water B -20 ft 3- Find the total pressure and position of center of pressure FREE WATER SURFACE on a triangular plate of base 2 m and height 3 m which is 60 2.5 immersed in water in such a way that the plane of the plate -2 m- makes an angle of 60 with the free surface of the water. .3 The base of the plate is parallel to water surface and at a depth of 2.5 m from water surface.
Determine the magnitude and point of application of the horizontal and vertical compenents of the hydrostatic pressure force acting on the prismatic surface a b c d e. The surface lenght (dimension perpendicular to the figure) is 4.5 m. The unit weight of water =9.81 Kn/m3