An electromotive force of 100 volts is applied to an RC series circuit, in which the resistance is 200 ohms and the capacitance is de10-4 farads. Determine the load q(t) of the capacitor, if q(0) = 0. Find the current i(t

An electromotive force of 100 volts is applied to an RC series circuit, in which the resistance is 200 ohms and the capacitance is de10-4 farads. Determine the load q(t) of the capacitor, if q(0) = 0. Find the current i(t

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter24: Resistive-inductive-capacitive Parallel Circuits

Section: Chapter Questions

Problem 1RQ: An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in...

See similar textbooks

Related questions

Q: Consider the R-C circuit. we idealise the emf to be constant and have zero internal resistance. We…

A: as stated, the capacitor is initially not charged. and it is conneced in series with the resistance…

Q: A coil of inductance 100 mH and resistance 800 ohm is connected in parallel with a variable The…

A: The required parameters can be calculated when the circuit reaches resonance. At resonance the…

Q: A 12 volt battery is connected to a series circuit in which the inductor is 12 henry and the…

Q: Draw the root location curves of the system given in the block diagram in the figure? R(s) K G(s)…

A: Root Locus

Q: A fault current limiter as shown in the figure, has L1 = 1 mH and a total impedance of j10 Q. If the…

A: The given circuit is as shown below,

Q: Consider an LRC series circuit with a resistance of 2.5 ohms, capacitance of 0.1 farad, an…

A: Assuming, Electromotive force, E(t)=2cost+sint Volts.and, qp(t)=0.05cost+0.2sint

Q: d) The motor of the Car is operated using a synchronous machine. The voltage of operation at time t…

Q: An electromotive force of 100 volts is applied to an RC series circuit, in which the resistance is…

Q: Task 2: Consider the electrical system in the figure below, derive a differential equation that…

Q: 200-volt electromotive force is applied to an RC series circuit in which the resistance is 1000 ohms…

Q: Consider the simple series circuit that has an inductor, a resistor, and a capacitor shown in the…

A: Given, i(t)=current in a circuit, q(t)=charge in a circuit. R=resistance, L=inductance,…

Q: Consider an inductor whose inductance varies as L(x) 0.25H/cm-z, where is the variable length of the…

Q: By applying Kirchhoff's Voltage Law to a series RL circuit, we obtain the differential equation: di…

Q: Consider the circuit shown in the figure, with ε=36.0V,R0=50.0Ω,R=150Ω andL=4.00H. (a) Switch S1 is…

Q: Consider a series circuit consisting of a resistor of RR ohms, an inductor of LL henries, and…

A: Given:-didt+RLi=1LV(t)I(0)=0AR=70ohmL=5HV(t)=10V

Q: What is the general reason why capacitor voltage is selected with a value greater than 400V (such as…

A: The capacitor is generally designed for the higher value because it reduces the voltage drop across…

Q: By applying Kirchhoff's Voltage Law to a series RL circuit, we obtain the differential equation: di…

Q: Consider an LRC series circuit with a resistance of 2.5 ohms, capacitance of 0.1 farad, an…

Q: For the circuit in the figure, initially the switch S is closed in (b), until the capacitor is…

A: Given R=75 Ω L=22 mH C=15 nF E =20 V

Q: Phasors I, and Vs The circuit represented in Figure 2 is operating in the sinusoidal steady-state.…

Q: Propose set of differential equations that fully describe the behavior of the system shown in Figure…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Draw the root location curves of the system given in the block diagram in the figure? R(s) K G(s)…

Q: Plot the graph between P vs Va in Dc shunt excitation motor

A: In dc shunt motor speed is nearly constant. The relation between power and voltage is non linear.…

Q: Q1. For the system shown in Figure (1) E. R(a) C( K₁ 2+1 D(a) Figure (1) Design the values of K, and…

A: A block diagram of closed-loop control system is given in the question. The steady state error due…

Q: Consider the circuit shown below with R=1k2, L=1mH. a. Write the differential equation for the…

A: In this question, R L circuit are given as shown in the figure. Find the differential equation…

Q: 5. RC Charging Circuit is shown in the figure. Find the differantial equation and its solution of…

A: By applying KVL, V=RI+ 1/C ∫I dt By differentitaing, 0=R dI/dt+ IC 0=R dQ/dt + Q/C dQ/dt et/RC +…

Q: 2. A sinusoidal e.m.f. 110 sin 400t volts is connected in series in a circuit with an inductance of…

Q: Consider the circuit shown in the figure, with ε=36.0V, R0=50.0Ω, R=150Ω and L=4.00H. (a) Switch S1…

A: (a): The initial current in the circuit is zero. When the switch S1 is closed at t = 0, the inductor…

Q: Q5: For the closed loop system shown in figure below, where R(s) is unit step function. (1)…

Q: The differential equation for the instantaneous charge q(t) on the capacitor in LRC-series circuit…

Q: The four arms of a bridge supplied from a sinusoidal source are configured as follows: Arm AB: A…

Q: In the circuit shown in Figure 1, find the values of R and C such that the steady-state voltage…

A: In this question we have to find the value of R and C

Q: 1500 W heating elements at an initial temperature of 15 C is connected to supply voltage of 115V.…

A: The solution can be achieved as follows.

Q: For the circuit below with input voltage V1, a step function of magnitude 15 volts at time t=0, find…

A: A circuit's transient response is a short-term change in how it operates as a result of an external…

Q: Q5/A/ Calculate the maximum and minimum current in this conditions,(1- have maximum transmission, 2-…

A: Given :Characteristic impedance=50 ΩApplied power=50 Wi) Have maximum transmission :For, maximum…

Q: When the average real power absorbed by an impedance is zero, then the impedance is: Select one: a.…

Q: A voltage source is supplying a load through a long cable. The load is consuming 250 VA at 0.82…

Q: Answer following questions: (a) At t = 5 ms, a sinusoidal current i is known to be zero and going…

Q: In Figure, suppose the switch has been closed for a time interval sufficiently long (steady state)…

Q: A 90-ohm resistor, a 32 mH inductor, and a 5 uF capacitor are connected in series across the…

Q: Refer to attached image

A: If we give supply to an uncharged capacitor then at time (t=0) it behaves like short circuit and at…

Q: E5.18 A system is shown in Figure E5.18(a). The response to a unit step, when K=1, is shown in…

A: The given system is shown below: The transfer function of the above system is,…

Q: A circuit containing a 10 Ohms resistance is in series to 250 microFarad capacitance with a source…

A: Circuit will reach steady state in 5T sec where T is time constant in seconds. For RC circuit time…

Q: For the system: G(s) 8/(5s + 44) Compute (design) a Control gain (K>0) to obtain a 8% of steady…

A: Simple problem on control system Look below for the solution once:-

Q: 5. An RC (DC) circuit consists of a Resistor with a resistance of 25000 2 and Capacitor in series…

Q: (d) Find the steady-state and peak values of the response for this gain. (e) Find the value of gain…

Q: The resistance and inductance of a coil can be obtained by connecting the coil in series with a…

Question

Differential Equation Applications

An electromotive force of 100 volts is applied to an RC series circuit, in which the resistance is 200 ohms and the capacitance is de10^-4 farads. Determine the load q(t) of the capacitor, if q(0) = 0. Find the current
i(t)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in parallel. The circuit is connected to a 240-V, 400-Hz power supply. Find the following values. XL=XC=IR=AIL=AIC=AP=WVARsL=VARsC=IT=AVA=PF=%=
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
A 250-V circuit, consisting of a resistor, an inductor and a capacitor in series, resonates at 50 Hz. Thecurrent is then 1A and the p.d. across the capacitor is 500 V. Calculate (i) the resistance (ii) theinductance and (iii) the capacitance Answer:
4. A RC series circuit is composed of a resistor of resistance 50 ohms and a capacitor of capacitance 100µF. It is suddenly disconnected from a source voltage of 12V. Determine the time it takes for the voltage across each element is equal and determine the rate of change in the current at this time.
A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
Please explain this question properly A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
Using the series circuit in Figure 3 consisting of a voltage source V, the resistor R and the fully uncharged capacitor C, how to find the value of the capacitance C considering as known data the time constant of the circuit T and the value of the resistor R? V ww R
A resistor and a capacitor are connected in series across a 150V AC supply. When the frequency is 40Hz the circuit draws 5A. When the frequency is increased to 50Hz, it draws 6A. Find the values of resistance and capacitance. Also find the power drawn in the second case.
An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current.
A capacitor "C", an inductor "L" and a switch "S" are connected in series. When the switch is open, the plate to the left of the capacitor has charge "Qo". The switch is closed the load and current vary sinusoidally with time. Represent graphically the load "Qo" and the intensity of current "I" as a function of time "t", and explain why the current leads the load by a phase difference of 90°.
What impedance vector (0- j15) Ohms represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a capacitance.