An electric motor drives a stirrer fitted with a horizontal cylinder. The cylinder of 40 cm diameter contains a fluid restrained by a frictionless piston. During the stirring of fluid for 15 min the piston moves outward slowly by a distance of 30 cm against the atmospheric pressure of 1 bar. The current supplied to the mo- tor is 0.5 amp. from a 24-V lead-acid accumulator. If the conversion efficiency firom electrical work to mechanical work output is 90%, estimate the work done on the motor, stirrer and the atmosphere.

An electric motor drives a stirrer fitted with a horizontal cylinder. The cylinder of 40 cm diameter contains a fluid restrained by a frictionless piston. During the stirring of fluid for 15 min the piston moves outward slowly by a distance of 30 cm against the atmospheric pressure of 1 bar. The current supplied to the mo- tor is 0.5 amp. from a 24-V lead-acid accumulator. If the conversion efficiency firom electrical work to mechanical work output is 90%, estimate the work done on the motor, stirrer and the atmosphere.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A ventilation system includes a fan with a mechanical efficiency of 45% against a static pressure of 30cm WG. If the total pressure created by fan is 300m of air, what is the static efficiency?
Skg of Steam at pressure of 4.9 bar is produ- ced from water at 20c. Determine the amount of heat supplied if the Steam is o.9 dy.
A gas engine working on the constant-volume eveleave the following results during a one-kaur test run. Cylinder diameter 24 cm; stroke 48 cm; torque 770 a verage speed 220 rpm; average explosion per minute 77: mep 7.5 DD 7volume of gas used 12 m at , 2 and 770 mm of mercury pressure; lower calorific value of gas 21 inlet and outlet temperature of cooling water are 25 °C and 60 °C respectively; cooling water used 600 kg. Determine (i) the mechanical efficiency (ii) the indicated Specific gas consumption in m³/kW h and (iii) the indicated thermal efmal y. 6m3 at NTP: Draw up a heat balance for the engine on minute basis., explaining why friction power has been included in or omitted from your heat balance. NTP conditions are 760 mm of Hg and 0 °C.
please solve with explanation nad step by step
I was not sure how to write the equllibrium equations for this problem and find P.
Please solve this problem, Thank you
Answer the second problem Only
The vacuum at the steam inlet to a condenser was found to be 716 mm of Hg and the temperature of steam in the condenser is 35 o C, when barometer reads 760 mm of Hg. Find the vacuum efficiency.
aal 1Banrallng Mament 4m
can you please find solution for this question and the FBD
8. Air is compressed in a frictionless steady-flow process from 70 kN/m2, -29°C and a specific volume of 1 m³/kg to 100 kN/m² in such a manner that p(u+0.5)=constant, where v is in m³/kg. Inlet velocity is negligibly small and discharge velocity is 100 m/s. The flow rate is %3D 0.2 kg/s. Calculate the work required in kW. [ans: -5.49 kW]
A piston and cylinder machine containing a fluid system has a stirring device in the cylinder. The piston is frictionless and is held down against the fluid due to the atmospheric pressure of 101.325KPa. The stirring device is turned 10000 revolutions with an average torque against the fluid of 1.275mN. Meanwhile the piston of 0.6m diameter moves out of 0.8m. Find the net work transfer for the system.